SEI FA580800TX User manual

FA580800TX
Antique Gold Brush Leaf Motif
Wall Mount Fireplace
Assembly Instruction
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
©
©©
©Southern Enterprises Inc. All Right Reserved.

Tool List: 1/4" drill bit, drill, tape measure and pencil.
FA580800TX
Antique Gold Brush Leaf Motif Wall Mount Fireplace
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Screws shown actual size. Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study
the screw diagrams below (SHOWN ACTUAL SIZE). You may receive extra
hardware with your unit.
Suggested tools: Phillip head screw driver, power drill, ¼” drill bit, 24”
level, and a tape measure. Unit needs to be hung on wall stud for more
security and stability.
(1) Fireplace assembly
1 PC
(2) Fuel canister holder
3 PCS
(3)Candle holder
1 PC
(4)Plastic wall anchor
4PCS
1 extra included
(5) Phillip head screw
4PCS
￠
￠￠
￠4mm ×1-3/4″
1 extra included
Care and Cleaning Instructions:
Before using , wipe with a clean , dry cloth.
Periodically apply furniture wax to renew
The finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Do not return product to store. Please call
manufacturer for assistance, questions or
parts.
Assembly Tool Required
No.2 Phillips Screwdriver

FA580800TX
Antique Gold Brush Leaf Motif Wall Mount Fire
Assembly Instructions
DANGER
PLEASE USE IN WELL VENTILATED AREA
The fireplace will have open flames and will generate heat.
Make sure to keep all combustible items away from the fireplace when the gel fuel is
burning.
DO NOT touch the fireplace when the gel fuel is burning.
Not recommended for use on wall paper or wood paneled walls due to risk of
discoloration over time.
1. Locate the fireplace on a solid
wall and at a comfortable height
off the floor, normally eye level.
2.Measure the wall and mark the
fireplace width and height. See
Figure 1.
Figure 1 – Installation Measurements
Eye Level
27
2727
27"
""
"
22-1/2"

Phillip head screw
Anchor
3. Measure the wall and mark the
location of the center of each of
the three screw mounting holes.
See Figure 2.
Using the level, make sure that all
three marks are level on the wall.
It’s highly recommended that
middle screw is inserted into a
wall stud.
4. Using the power drill and
1/4″drill bit, drill three 1/4″holes
through the wallboard at the
mounting hole marks.
NOTICE
Make sure not to drill into
electrical wiring or plumbing
pipes.
5. Insert one of the furnished
plastic anchors into each of the
three 1/4″holes. See Figure 3.
Make sure that the wall anchor is
flush with the wall.
NOTE: It may be necessary to
use a small hammer to gently tap
the anchor into place.
6. Using the phillip head
screwdriver, install one Phillip
Head Screw into each of the
anchors. See Figure 3. Turn the
screw in until there is a gap of
1/4″between the head of screw
and the wall surface.
Figure 2 – Screw Hole Location
Figure 3 – Wall Anchor Installation
2
1-5/8
7
-
1/8"
Drill three 1/4" holes
into wall
6
-
3
/8"
14
-
1/4
1/4" Gap
1/4" Hole

7. Install the fireplace (1, Figure
4) onto the three mounting
screws using the mounting holes
(2, Figure 4). The proper and
secure mounting of the fireplace
is when the top edge of each of
the mounting holes is resting
securely on the mounting screw
(3, Figure 4).
NOTICE
Using the level, check to make
sure that the fireplace is
horizontally level and vertically
plumb (straight up and down).
8. Remove the three fuel canister
holders (2,Figure 5) from the
fireplace and install one gel fuel
canister(1, Figure 5) into each of
the holders.
NOTICE
Make sure to remove the gel fuel
canister paper label (4,Figure 5)
before installing the canister into
the holder.
Shake the gel fuel canister before
installing it into the canister
holder.
Figure 4 – Install Fireplace
Figure 5 –Fuel Canister Holder and Gel Fuel Canister
2
3
1

Figure 6 – Fuel Canister Installed
9. Install the gel fuel holders into
the fireplace into the appropriate
mounting hole (3, Figure 5) in the
fireplace.
10. Following the instructions on
the gel fuel canister, remove the
lid (2,Figure 6) from the gel fuel
canister (1,Figure 6), and using a
long match, light the fuel in each
of the canister. Candle holder can
be used to extinguish fire.

DANGER
PROLONGED USE OF THE GEL FUEL IN THE FIREPLACE WILL CAUSE THE FIREPLACE
TO BECOME HOT AND POTENTIALLY CAN CAUSE BURNS IF TOUCHED.
DO NOT BURN MORE THAN THREE CANISTERS OF FUEL AT ONE TIME.
BEFORE LIGHTING THE FUEL, MAKE SURE THAT THE PAPER LABEL IS REMOVED
FROM EACH OF THE GEL FUEL CANISTERS.
USE LONG MATCHES TO LIGHT EACH CANISTER OF FUEL.
DO NOT TOUCH THE CANISTERS WITH BARE HANDS UNTIL THE FLAME HAS BEEN
EXTINGUISHED FOR 20 MINUTES.
DO NOT BURN ANYTHING EXCEPT THE SPECIFIED CANISTERS OF GEL FUEL IN THE
FIREBOX.
KEEP CHILDREN AWAY FROM THE FIREPLACE WHEN IN USE.
KEEP FLAMABLE OBJECTS, SUCH AS CURTAINS OR DRAPERYS, AWAY FROM THE
FIREPLACE WHEN THE GEL FUEL HAS BEEN IGNITED.
MAKE SURE THE CUSTOMER DOES NOT PLACE ANY DECORATIVE ITEMS ON TOP OF
THE UNIT AT ANYTIME.
DO NOT TOUCH THE UPPER PART OF THE UNIT WHILE IT IS STILL IN OPERATION.
THE CANDLE HOLDER ACTS AS A COVER TO PUT OUT FIRE IF ONE WISHES TO STOP
THE FLAME.
NEVER LEAVE BURNING GEL FUEL UNATTENDED.
CARE INSTRUCTION: WIPE DOWN UNIT AND CANDLE HOLDER WITH SOFT DAMP
CLOTH.
WHEN USING THE CANDLE HOLDER PLEASE MAKE SURE THAT THE CANNISTER
HOLDERS ARE IN PLACE.

We'd love to hear from you! Email us photos of our products in your home at
[email protected] and we might feature it on our site or use it to model one of our
inspirational photos.
“PARTS WILL BE SENT IF AVAILABLE FROM SEI”
Parts Replacement Form
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/ Website/ Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
2915 Merrell Road
Dallas, Texas 75229