SEI HZ104100TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
customer service 1-800-633-5096
[e-mail]
www.seidal.com
HZ104100TX
Black Contemporary Bar
Cabinet
Assembly Instructions
PO#：
P
age 1

A
Quantity
of 1
top panel
B
Quantity
of 1
bottom panel
C
Quantity
of 1
left side panel
D
Quantity
of 1
right side panel
E
Quantity
of 2
fixed shelf panel
F
Quantity
of 1
back panel
G
Quantity
of 3
wine rack shelf panel
H
Quantity
of 4
wine rack vertical panel
I
Quantity
of 1
left door
J
Quantity
of 1
right door
K
Quantity
of 4
door shelf panel
L
Quantity
of 1
drawer front
M
Quantity
of 1
left drawer side
N
Quantity
of 1
right drawer side
O
Quantity
of 1
drawer back
Black Contemporary Bar Cabinet
Parts list
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface
like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware
according to the pictures. Using the incorrect hardware will cause damage.
Page 2
u p

P
Quantity
of 1
drawer bottom
Q
Quantity
of 4
middle glass rack
R
Quantity
of 2
side glass rack
S
Quantity
of 4
legs
T
Quantity
of 4
metal rack
1
Quantity
of 32
wood dowel
Dia 5/16” x 1-3/16”L
2
Quantity
of 32
cam bolt
3
Quantity
of 32
cam lock
4
Quantity
of 6
hinge
5
Quantity
of 86
short screw: Dia 1/8” x 1/2”L
6
Quantity
of 22
round head screw: Dia 1/8” x 1/2”L
7
Quantity
of 2
knob
8
Quantity
of 2
small bolt
9
Quantity
of 2
magnet
10
Quantity
of 1
left female slide
11
Quantity
of 1
left male slide
12
Quantity
of 1
right female slide
13
Quantity
of 1
right male slide
Page 3

14
Quantity
of 4
L bracket
15
Quantity
of 18
long screw: Dia 1/8” x 1-1/4”L
16
Quantity
of 4
medium screw: Dia 1/8” x 1”L
17
Quantity
of 4
wall bracket screw: Dia 1/8” x 5/8”L
18
Quantity
of 2
wall bracket
19
Quantity
of 2
plastic strap
20
Quantity
of 2
anchor
21
Quantity
of 4
wall screw: Dia 1/8”x 1-3/8”L
Care and cleaning i
nstructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096
Assembly Tool Required No.2 Phi
Tool List: 3/16" drill bit, drill, tape measure and pencil.
Page 4
Assembly Tool Required No.2 Phillips
Screwdriver (Not included)

Fi ure 1
Wood may scratch easily, be careful
when assembling.
Attach left female slide (10) to left
side panel (C) with short screws (5).
Tighten short screws (5) with a
phillips screwdriver.
Tip: Make sure to attach short
screws (5) in the same hole on left
female slide (10) as shown on inset.
If you have correctly attached one
screw, every other screw should
align with the holes on female left
slide (10). The front of the panel can
be distinguished by the finish.
Fi ure 2
Attach right female slide (12) to right
side panel (D) with short screws (5).
Tighten screws with a phillips
screwdriver.
Tip: Make sure to attach short
screws (5) in the same hole on right
female slide (12) as shown on inset.
If you have correctly attached one
screw, every other screw should
align with the holes on right female
slide (12).
Black Contemporary Bar Cabinet
Assembly Instructions
Page 5

Fi ure 3
Insert cam locks (3) into holes on
fixed shelf panels (E)
Screw cam bolts (2) into holes on
left side panel (C).Attach left side
panel (C) to fixed shelf panels (E)
by inserting wood dowels (1) and
cam bolts (2) into corresponding
holes until left side panel (C) and
fixed shelf panels (E) meet.
Tighten by rotating cam lock (3)
clockwise with a p
hillips screwdriver
Repeat procedure to attach right
side panel (D) to fixed shelf panels
(E)
Fi ure
4
Insert cam locks (3) into holes on
pre-assembled unit. Screw cam
bolts (2) into holes on the bottom of
top panel (A). Attach top panel (A)
to pre-assembled unit by inserting
wood dowels (1) and cam bolts (2)
into corresponding holes until top
panel (A) and pre-assembled unit
meet.
Tighten by rotating cam locks (3)
clockwise with a phillips
screwdriver.
Attach magnet (9) to top panel (A)
with round head screw (6).
Tighten screws with a phillips
screwdriver.
Fi ure
5
Insert cam locks (3) into holes on
pre-assembled unit.
Screw cam bolts (2) into holes on
the top side of bottom panel (B).
Attach bottom panel (B) to
pre-assembled unit by inserting
wood dowels (1) and cam bolts (2)
into corresponding holes until
bottom panel (B) and
pre-assembled unit meet.
Tighten by rotating cam locks (3)
clockwise with a phillips screwdriver
Attach magnet (9) to bottom panel
(B) with round head screws (6).
Tighten screws with a phillips
screwdriver.
Page 6
3
E
E
C
D
B
2
2166

Fi ure 6
Attach legs (S) to pre-assembled
unit by hand.
Attach middle glass racks (Q) and
side glass rack (R) to
pre-assembled unit with wood
dowel (1) and long screws (15).
Tighten long screws (5) with a
phillips screwdriver.
Fi ure 7
Attach wine rack vertical panel (H)
and wine rack shelf panel (G)
together as shown.
Fi ure 8
Insert pre-assembled wine rack to
the unit from the back as shown.
Page 7
R

Fi ure 9
Attach back panel (F) to the
backside of pre-assembled unit with
round head screw (6).
Tighten screws with a phillips
screwdriver.
Tip: Make sure the arrow on back
panel (F) is pointing up.
Fi ure 10
Attach metal rack (T) to left door (I)
and right door (J) with short screws
(5).
Attach knob (7) to left door (I) &
right door (J) with small bolts (8).
Tighten screws and small bolt with a
phillips screwdriver.
Fi ure
11
Insert cam locks (3) into holes on
door shelves (K).
Screw cam bolts (2) into holes on
pre-assembled doors.Attach door
shelves (K) to pre-assembled doors
by inserting wood dowels (1) and
cam bolts (2) into corresponding
holes until door shelves (K) and
pre-assembled doors meet.
Tighten by rotating cam locks (3)
clockwise with a phillips
screwdriver.
Repeat steps for the second door.
Page 8
F
up
6
6
6
66
6
6
6
6
6
6
7
8
I/J
T
T
22

Fi ure 12
Attach L brackets (14) to
pre-assembled doors with screws
(5).
Tighten screws with a phillips
screwdriver.
Fi ure 13
Attach hinges (4) to the sides of the
pre-assembled unit with short
screws (5).
Tighten screws with a phillips
screwdriver.
5
4
4
4
555
4
55
5
5
5
5
5
5
Page 9

Fi ure 14
Attach the left drawer side (M) and
right drawer side (N) to drawer
back panel (O). Make sure to line
up the grooves on panels (O, N,
and M). Secure panels (O, N, and
M) with medium screws (16).Insert
drawer bottom panel (P) into the
corresponding grooves of drawer
back panel (O) and left drawer side
(M) and right drawer side (N).
Insert cam locks (2) into predrilled
holes on left drawer side (M) and
right drawer side (N).
Screw cam bolts into holes on the
backside of drawer front (L),
Attach drawer front (L) to
pre-assembled drawer box by
inserting cam bolts (2) into
corresponding holes until drawer
front (L) and pre-assembled drawer
box meet.
Tighten by rotating cam locks (3)
clockwise with a phillips
screwdriver.
Fi ure
15
Attach left male slide (11) and right
male slide (13) with short screw (5)
to pre-assembled unit.
Tighten screws with a phillips
screwdriver.
2
5
55
Page 10

Fi ure 16
Insert drawer box into the unit.
Please check to make sure the
drawer box male slides are inserted
into side panel’s female slides.
Fi ure 17
Attach wall bracket (18) to the back
panel using wall bracket screw
(17). Tighten wall bracket screw
(17) using a phillips screwdriver.
Mark two desired locations on the
wall and drill two 3/16" holes. Insert
plastic anchors (20) into the two
holes on the wall as shown, you will
need a hammer help you.
Then attach the wall bracket (18) to
the wall using wall screws (21).
Tighten wall screws (21) using a
phillips screwdriver.
w a ll
1 8
2 1
2 0
1 7
1 8
1 8
2 1
2 0

Fi ure 18
Move this item close to the wall and
tie both wall brackets (18) with
plastic strap (17) as shown in
diagram.
Anti-tipping hardware must be
used for this product to avoid
tipping and injury.
Fi ure
1
9
Your black contemporary bar
cabinet is ready for use.

Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are
not responsible for any damages due to product modification(s). If damages or missing parts are not reported within
90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central time if
you have product issues or email us at [e-mail]. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with
product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 12
Page 11