SELF SPTK-0001LVT User manual

SPTK
SPTK

INSTRUCTION MANUAL
SERIES: SPTK
1
www.self-electronics.com
2
www.self-electronics.com
SPTK-0201MTA
(ARM-SPTK)
1/8”(2.5)
2-1/16”(52.5) 12-7/16”(316)
2-3/4”(70)
11-4/16”(286.5)
11
Dimensions: (inches/mm)
-
Shelf bracket of SPTK
with 2" output cable + HAA250G socket.
9/16”(14)
1-7/16”(37) 1-3/8”(34.8)
7/8”(22)
1/4”(5.8)
7/16”(11.5)
SPTK-0102CA
(ADP-SPTK)
Dimensions: (inches/mm)
The adaptor of SPTK
Max output 2A.
9/16”(14)
1-5/8”(13.2)1/2”(13.2)
1’(26)
with 59" cable + PDL plug.
SPTK-0101CA
(IC-SPTK-59)
(TC-SPTK)
Dimensions: (inches/mm)
Input cable of SPTK
-
Top cap of SPTK
9/16”(14)
1-5/8”(13.2)1/2”(13.2)
1’(26)
ATTENTIONS
Read these instructions completely and carefully.
3/8”(10.2)
9/16”(14)
15/16”(24.2)
1-7/16”(37)
7/16”(10.9)
Dimensions: (inches/mm)
SPTK-0001LVT
(SPTK-95)
The track of SPTK
Length(inch) 66-15/16”(1700)
• Read the instruction carefully before installation，non-observance of this instruction may cause damage to the fixture or hurt
to human body. The installation must be carried out by a qualified electrician in accordance with local or national codes.
• Cut off the power supply before installation, maintenance or cleaning.
• Regularly check the light source , the LED power supply, the cord and other accessories. If any part is damaged, the product
should not be used.
• Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation.
Do not leave any other open holes in an enclosure of wiring or electrical components.
• Keep this instruction manual handy for future use.
• The light source of these product are non-changeable light diodes(LED).
Do not disassemble the product, as the light diode can cause damage to the eyes.
WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If
not qualified, do not attempt installation. Contact a qualified electrician.
WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings.
WARNING - Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of
LED retrofit kit. Check for enclosed wiring and components.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CAUTION - To reduce the risk of fire, do not install in a compartment smaller by L1 inches by 15-3/4 inches by 15-3/4 inches.
AVERTISSEMENT - Afin d’éviter tout risques d’incendie, ne pas installer dans un compartiment plus petit par L1 inch, par
15-3/4 inch, par 15-3/4 inch.
L1 see form①.
Use only with SELV power supply or Class 2 power supply (For USA market)
• Track system for low voltage, max 12V, 4A or 24V, 4A
• For adaper, max. output current 2A
• Max. Fuctional load is not greater than 30kg per layer

www.self-electronics.com
4
www.self-electronics.com
3
Tools:
Tape Measure
2
3
4
5
Track installation:
Electrical Safety Gloves
1
2
3
Driller
Install the power track of SPTK.
Install the wall panel.

Shelf installation: Wiring:
www.self-electronics.com
6
www.self-electronics.com
5
2
1
1
2
Install the shelf bracket onto shelf. Install shelves onto power track one by one.
Install endcap of SPTK.
Connect the adaptor of SPTK with LED light.

www.self-electronics.com
8
www.self-electronics.com
7
SELF Electronics Co.,Ltd.
No. 1345 JuXian Road, Ningbo Hi Tech Park, Ningbo, China 315103
21/07/2021
Power on
3
5
4
Install the input cable of
SPTK into power track.
Connect to LED power supply.
Quantity of the layer no more than 5 pcs per system,
Max. Fuctional load is not greater than 30kg per layer.
Caution: