LUMENWERX RIM VERSO ACOUSTIX User manual

Slightly loosen the screws (A) on the side of the
canopy (B). Remove the canopy plate (C). Fix the canopy (B) on the junction box (D).
Use the canopy (B) as a model to mark 4 holes.
Remove the canopy. Drill holes (1/4” diameter)
following the red marks. Install #8 screw anchors(E).
Tighten the two screws to secure the canopy (B)
to the Junction box (D).
This product must be installed in accordance
with the National Electrical Code and all
applicable local codes, by a person familiar with
the construction and operation of the product,
and the hazards involved. proper grounding is
required for safety.
Ce produit doit être installé suivant le code
national de l’électricité, ainsi que tous les codes
locaux applicables, par une personne familière
avec la construction et le fonctionnement
du produit, ainsi que tous les risques qui y
sont associés. la mise à terre électrique est
obligatoire pour la sécurité.
BB
B
B
D
D
C
A
E
RIM-VERSO-ACOUSTIX-CANOPY-DRIVER-BOX-POC-INST February 13, 2020 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
IMPORTANT: Installation instructions are shown with RIMR24 and applies to all RIM VERSO NOTE: Wire dimming conductors as Class 1
WWW.LUMENWERX.COM
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
21
43 5
RIM VERSO ACOUSTIX CANOPY DRIVER BOX - POC - INSTALLATION INST.

DRIVER
+
+
-
Make electrical connections between the driver (I)
and the main power (J) with marettes (K). Notes:
Connect the green wire to your ground wire.
Make sure to have a steady hold of the fixture. So,
it is never hanging loosely from POC (Power Over
Cable) if installation is not complete. Warning :
Power must come from Single branch circuit.
Pass all aircraft cables (F) through the canopy plate
(C). Insert them into the grippers (G). Adjust the
cables by pushing the feeder tube (G).
Notes: Height adjustment of the fixture must
be done at this step. Rim 36”, 48” and 60” have 4
wires.
Use #8 screws to fasten the canopy (B) to the
ceiling.
cut the excess cable with an aircraft cable cutter
(H). Notes: Leave POC (Power Over Cable) length
of 1.5” to make the connection inside the J-box.
I
K
J
F
H
C
G
B
Make electrical connections between POC (Power Over Cable) (L) and the driver (M). Notes: Make sure
that you are connecting the negative (-) POC (as mark on the fixture with black color and a label) to
your negative wire and the positive (+) POC (as mark on the fixture with red color and a label) to your
negative wire.
M
L
(+) cable
(-) cable
(+) cable (-) cable
February 13, 2020 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
6 7 8
109
RIM-VERSO-ACOUSTIX-CANOPY-DRIVER-BOX-POC-INST
RIM VERSO ACOUSTIX CANOPY DRIVER BOX - POC - INSTALLATION INST.

C
+
+
Put canopy plate (C) back in place.
Organise the wires that will be placed inside the
canopy. Make sure that the low voltage (+)
and (-) are more than 1” away from the branch
circuit.
Secure the canopy plate (C) onto the canopy (B) by
tightening the two screws (A) on the sides. Cut the
lables (N) off the wires.
(-) cable
(+) cable
> 1’’
> 1’’
A
B
C
N
February 13, 2020 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
11 12
RIM-VERSO-ACOUSTIX-CANOPY-DRIVER-BOX-POC-INST
13
RIM VERSO ACOUSTIX CANOPY DRIVER BOX - POC - INSTALLATION INST.