Sena 50 Series User manual
1
2
Sena WiFi Adapter for 50 Series
Quick Start Guide
2.0.0
ENGLISH
USB-C
Connector
USB
Connector
Factory Reset Button
LED
Indicators
2
Sena 50 Utility App
• Download the Sena 50 Utility App to set up the WiFi
Adapter to automatically upgrade your main unit.
Android: Google Play Store > ‘Sena 50 Utility’
iOS: App Store > ‘Sena 50 Utility’
• Save time updating the rmware on the main unit with the
Sena 50 Utility App and enjoy your adventure even more!
Connection Setup
1. Open the Sena 50 Utility App.
2. Click the top left Menu button and select the “WiFi
Adapter” menu.
3. Follow the instructions on the Sena 50 Utility App to
connect the WiFi Adapter to a WiFi access point.
Note:
To change the WiFi access point, perform the Factory
Reset then repeat the steps above.
3
Upgrading the Firmware of the Main Unit
The rmware will be upgraded automatically while your main
unit is charging. If you want to manually upgrade the rmware,
change the setting on the Sena 50 Utility App.
Note:
Do not disconnect the WiFi Adapter while upgrading the
rmware. The product may be damaged.
LED Description
Charging Status
Firmware Upgrade Status
WiFi Status
4
Charging Status
Disconnected
Charging (The main unit is powered off.)
Fully charged
Note:
Charging (The main unit is powered on.)
To upgrade the rmware, power off the main unit.
Firmware Upgrade Status
Disconnected or no rmware upgrade available
Upgrading rmware
Firmware upgrade completed
WiFi Status
Disconnected from an WiFi access point
Searching for WiFi access point
Connected to an access point
5
Powering On
Insert the USB Connector into a USB charger port that is
connected to a power source.
Note:
1. Any 3rd party USB charger (5 V/1 A) can be used with
WiFi Adapter if the charger is approved by either the
FCC, CE, IC or other locally approved.
2. Do not connect the WiFi Adapter to a USB port on
your PC.
Connecting to the Main Unit
Insert the USB-C Connector into the main unit’s USB-C port.
Note:
If you leave the main unit on when connecting it, the
charging LED on the WiFi Adapter will blink red slowly.
5
Sena Technologies, Inc.
Customer Support: sena.com
Factory Reset
If you want to restore the WiFi Adapter to the factory default
settings, you can easily reset the unit:
1. Gently insert a paperclip into the pinhole on the back of
the unit and lightly press the Factory Reset Button.
2. The WiFi Adapter will automatically restart with the three
LEDs on.
Note:
The WiFi Adapter will be restored to factory default
settings which include the WiFi conguration setup, the
rmware setup and the language setup.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment should be installed and operated with minimum distance 20cm between
the radiator and your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICE-003.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
L'appareil a été évalué pour répondre aux exigences générales d'exposition RF.
L'appareil peut être utilisé dans des conditions d'exposition fixes / mobiles.
La distance de séparation minimale est de 20 cm.
Table of contents
