Sencor SOC 1100SL Repair manual

- 1 - 05/2020 Copyright © 2020, Fast ČR, a.s.
EN Electric Sonic Toothbrush
Translation of the original manual
SOC 1100SL
SOC 1101RD
SOC 1102TQ

- 2 - 05/2020 Copyright © 2020, Fast ČR, a.s.
EN Electric Sonic Toothbrush
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
■ Toothbrushes may be used by children and persons with reduced
physical or mental capabilities or with a lack of experience and
knowledge, if they are supervised or have been instructed to
use the appliance in asafe manner and understand the potential
dangers.
■ Children must not play with the appliance. Cleaning and
maintenance performed by the user must not be performed by
unsupervised children.
■ In the event that the power cord is damaged, have it repaired
at aprofessional service centre to prevent causing a dangerous
situation. It is forbidden to use the appliance if it has adamaged
power cord.
■ The parts of the appliance that need to be mounted or stood
upright, must be mounted or stood upright in such a way that
they cannot fall into water.
■ The appliance must only be powered using asmall safe voltage
corresponding to the markings on the appliance.
■ Only use the supplied original charging stand to charge the
toothbrush. Before connecting the charging stand to a power
socket, make sure the voltage stated on its rating label corresponds
to the voltage in your power socket.

- 3 - 05/2020 Copyright © 2020, Fast ČR, a.s.
■ This toothbrush serves to clean teeth and gums. Do not use it for purposes
other than those for which it was designed.
■ The toothbrush and its charging stand is intended for use in indoor areas. Do
not expose it to the eects of the outdoor environment, extreme temperatures,
direct sunlight or locate it in the vicinity of an open ame, heating elements
and other equipment or appliances that could be potential sources of heat.
■ Always locate the charging stand on an even and stable surface. Ensure that
the power plug contacts do not come into contact with water or moisture.
■ In the event that the charging stand is submerged in water, rst disconnect
it from the power socket and only then take it out of the water and dry it out
thoroughly.
■ Charge, use and keep the toothbrush at room temperature. Do not submerge
it in hot water.
■ For hygiene reasons, atoothbrush head should be used by only asingle user.
Regularly replace the toothbrush head every 3 months or sooner if it shows
signs of wear. Use only original replacement toothbrush heads.
■ When the toothbrush is used by children, supervise them while they are
brushing their teeth until they acquire the proper tooth brushing technique.
■ In the event that dental work or oral surgery was performed in the past two
months, consult the use of asonic toothbrush with your dentist.
■ In the event that gum bleeding occurs when the toothbrush is used and if
bleeding persists even after aweek of its use, contact your dentist.
■ In the event that using the toothbrush causes unpleasant or painful feelings,
stop using the toothbrush and consult this situation with your dentist.
■ In the event that you have apacemaker or another implanted device, consult
the use of the toothbrush with your doctor or manufacturer of the implant.
■ Perform cleaning and maintenance according to the instructions in chapter
Cleaning and maintenance.
■ Disconnect the charging stand from the power socket by gently pulling the
plug of the power cord, and not the power cord itself. Otherwise, this could
damage the power cord or the socket.
■ Do not make any modications to the toothbrush or its charging stand.

- 4 - 05/2020 Copyright © 2020, Fast ČR, a.s.
■ In the event that the toothbrush, charging stand or its power cord are damaged
in any way, do not use it. The power cord on the charging stand cannot be
replaced. In the event that it is damaged, the charging stand must be disposed
of and replaced with anew one. For replacement of acharging stand that is
damaged or has adamaged power cord and for all repairs of the toothbrush,
contact an authorised service centre. Do not repair the toothbrush yourself.
By tampering with the product you risk voiding your legal rights arising from
unsatisfactory performance or quality warranty.

- 5 - 05/2020 Copyright © 2020, Fast ČR, a.s.
A
1
2
3
4
6
5
7

- 6 - 05/2020 Copyright © 2020, Fast ČR, a.s.
B
C
45°

- 7 - 05/2020 Copyright © 2020, Fast ČR, a.s.
EN
Electric Sonic
Toothbrush
User'smanual
Prior to using this appliance, please read the user’smanual thoroughly,
even in cases, when one has already familiarised themselves with
previous use of similar types of appliances. Only use the appliance in the
manner described in this user’smanual. Keep this user’smanual in asafe
place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty
card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend
that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE TOOTHBRUSH AND ITS ACCESSORIES
A1 Toothbrush head*
A2 Ergonomically-shaped anti-slip
handle
A3 Button for turning the toothbrush
on and o and setting the
vibration speed (max. 41 000
vibrations per minute)
A4 LED indicator
signals the operation or charging
of the toothbrush
A5 Charging stand
A6 Power cord
A7 Travel case
*Note:
2 toothbrush heads are included.
ATTACHING AND REMOVING THE TOOTHBRUSH HEAD
Make sure that the toothbrush is turned o before attaching or removing
atoothbrush head A1.
Attach the toothbrush head A1 by sliding it on to the handle A2 from
above. Make sure that there is astrong connection of both parts.
Remove the toothbrush head A1 by pulling it o away from the handle
A2.
CHARGING THE TOOTHBRUSH
This toothbrush has a built-in Li-Ion battery that enables cordless
operation.
Make sure that the toothbrush is turned o before charging it.
Locate the charging stand A5 on an even and stable surface and plug
the power cord A6 into apower socket (100–240 V).
Put the toothbrush on to the stand A5 from above, see gure B. The LED
indicator A4 will be lit red. This signals the charging process. When the
battery is fully charged, the LED indicator A4 will be lit blue. After fully
charging, disconnect the charging stand A5 from the power socket.
Note:
Allow the toothbrush to charge for at least 15 hours before first use
and after not using it for along time.
If you are charging the toothbrush for the first time or if you have
not used it for along time, it may take up to 10 minutes before the
LED indicator A4 lights up.
A fully charged toothbrush will provide approximately 180 hours
of operation. If you brush your teeth twice a day for 2 minutes, the
toothbrush will last for 45 days without needing to be recharged.
HOW TO ACHIEVE THE LONGEST POSSIBLE BATTERY
LIFETIME
To ensure the longest possible lifetime of the battery, we recommend:
– Store, use and charge the battery at room temperature. Excessively
high temperatures may negatively aect its lifetime.
– do not unnecessarily leave the battery fully charged or completely
at for too long.
– do not keep the battery permanently fully charged.
– do not fully discharge the battery.
USING THE TOOTHBRUSH
Make sure that the toothbrush is properly assembled before using
it. Wet the toothbrush bristles and apply the toothpaste. Turn on the
toothbrush by pressing button A3.
1. CORRECT BRUSHING TECHNIQUE
We recommend to start by brushing the right half of the upper dental
arch from the outer side. When brushing, proceed from back to front.
Place the toothbrush bristles on to the teeth at an angle of 45° in line with
the gum, see gure C. Using short slow motions, move the toothbrush
to the other teeth. Once the outer side of the upper right dental arch
is brushed, move the toothbrush to the inner side of the dental arch.
Again, proceed from back to front. Adjust the toothbrush angle to the
tooth arrangement. When brushing the inner side of the front teeth of
the upper dental arch, hold the toothbrush handle A2 vertical so that
the tip of the toothbrush head A1 points upwards. Finally, brush the
upper tooth surfaces.
In the same way, brush the right half of the lower dental arch, the left
half of the lower dental arch and nally also the left half of the upper
dental arch. When brushing the inner side of the front teeth of the lower
dental arch, hold the toothbrush handle A2 vertical so that the tip of the
toothbrush head A1 points downwards.
2. SPEED SETTING
To increase the vibration speed, hold down button A3 for 3 seconds.This
can be done repeatedly until the desired speed is achieved. The change
in the speed setting is indicated by ashort ash of the LED indicator A4.
Another way to increase the speed is to hold down button A3 for
along time. The speed will increase gradually. The increasing speed is
indicated by the ashing LED indicator A4. When the maximum speed
level is achieved, the whole setting cycle will repeat from the beginning.
Release button A3 when the desired speed is achieved.
The set vibration speed is stored in memory.
Initially, until one becomes accustomed to the new way of brushing their
teeth, it is recommended to set alower speed.
3. 4PACER FUNCTION
The toothbrush has a timer function that momentarily pauses the
toothbrush every 30 seconds until it turns o automatically, thereby
informing the user that it is time to start brushing the next part of your
teeth. This will ensure that all the dental quadrants are brushed for the
same amount of time.
4. AUTOMATIC SHUT-OFF TIMER
The automatic shut-o timer automatically turns the toothbrush o after
2 minutes of operation. This is the tooth brushing time recommended by
dentists for the sonic toothbrush.
When you have nished using it, make sure that the toothbrush is
turned o and clean it according to the instructions contained in chapter
Cleaning and maintenance.Then put it back on to the charging stand A5
or into the case A7. Before putting it into the case A7, it is necessary to
remove the head A1 from the toothbrush handle A2.
CLEANING AND MAINTENANCE
For hygiene reasons, regularly clean the toothbrush after every use.
Make sure that the toothbrush turned o before cleaning it.
Thoroughly rinse the toothbrush head A1 under lukewarm running
water to remove any toothpaste or other remains. If whitening pastes
are used when brushing teeth, it is recommended to apply adrop of
soap on to the toothbrush head A1 and then thoroughly wash it under
running lukewarm water.
Rinse the toothbrush handle A2 under running lukewarm water and
then dry it.
In the event that the charging stand A5 is soiled, wipe it with aclean
dampened cloth and then wipe dry. Make sure that the plug on the
power cord A6 does not come into contact with water or moisture.
The travel case A7 may be wiped with adampened cloth or washed
under lukewarm running water. Then dry it thoroughly.
For cleaning, do not use abrasive cleaning products, thinners, etc.
Otherwise the surface of the appliance may be damaged.
REPLACING THE TOOTHBRUSH HEAD
Regularly replace the toothbrush head A1 every 3 months or sooner if it
shows signs of wear. Use only original replacement toothbrush heads.
Replacement toothbrush heads are available from you vendor both in
online and brick&mortar stores.
STORAGE
When not using the toothbrush for an extended period of time,
disconnect the charging stand A5 from the power socket and put the
toothbrush into the case A7.
Store the case A7 with the toothbrush and the charging stand A5 in
adry, clean place.

- 8 - 05/2020 Copyright © 2020, Fast ČR, a.s.
TECHNICAL SPECIFICATIONS
Toothbrush
Battery...........................................................................................Li-Ion / 3.7 V/ 800 mAh
Operating time when fully charged .............................................up to 180 minutes
Noise level ............................................................................................................... 65 dB(A)
Protection class level against damaging entry of water.................................. IPX7
Charging stand
Input ....................................................................................100−240 V~, 50-60 Hz, 1.4 W
Electrical shock protection class......................................................................................II
Protection class level against damaging entry of water.................................. IPX7
The declared noise emission level is 65 dB(A), which represents alevel Aof
sound power with respect to areference sound power of 1 pW.
Explanation of technical terminology
Safety class for electrical shock protection:
Class II – Electrical shock protection is provided by double or heavy-duty
insulation.
Protection class level against damaging entry of water:
IPX7 – The appliance is protected against damaging entry of water when
submerged at adepth of 1 metre for 30 minutes.
Changes to text and technical parameters are reserved.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your
municipality.
REMOVING THE BATTERY AT THE END OF THE
PRODUCT'SLIFETIME
Prior to disposing of the product or handing it over at aspecialised collection
facility, it is necessary to ensure that the built-in battery is removed. Allow
the battery to discharge before removing it. To remove the battery, proceed
as follows. Wrap the toothbrush handle A2 into an unneeded piece of cloth
and place it on an even, stable surface. Using asmall hammer, hit the handle
from the side afew times in the vicinity of the LED indicator A4. Rotate the
handle A2 and repeat this procedure until the bottom cover is released from
the handle A2. After releasing the cover, remove it and take out the built-in
battery. Battery removal may also be performed at an authorised service
centre. In the event that the product has been disassembled for the purpose
of ecological disposal then it must not be reassembled.
BATTERY DISPOSAL
The battery contains environmentally damaging substances
and therefore does not belong in standard household waste.
Hand it over for proper disposal at respective collection
locations.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that
used electric or electronic products must not be added to
ordinary municipal waste. For proper disposal, renewal and
recycling hand over these appliances to determined
collection points. Alternatively, in some European Union
states or other European countries you may return your
appliances to the local retailer when buying an equivalent
new appliance.
Correct disposal of this product helps save valuable natural resources and
prevents potential negative eects on the environment and human health,
which could result from improper waste disposal. Ask your local authorities
or collection facility for more details.
In accordance with national regulations penalties may be imposed for the
incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or
supplier for the necessary information.
Disposal in other countries outside the European Union
This symbol is valid in the European Union. If you wish to dispose of this
product, request the necessary information about the correct disposal
method from the local council or from your retailer.
This product meets all the basic requirements of EU directives
related to it.