- 6 - 05/2020
Copyright © 2020, Fast ČR, a.s.
EN Electric Sonic
Toothbrush
User'smanual
■ Prior to using this appliance, please read the user’smanual thoroughly, even in cases, when
one has already familiarised themselves with previous use of similar types of appliances. Only
use the appliance in the manner described in this user’smanual. Keep this user’smanual in
asafe place where it can be easily retrieved for future use.
■
We recommend saving the original cardboard box, packaging material, purchase receipt
and responsibility statement of the vendor or warranty card for at least the duration of the
legal liability for unsatisfactory performance or quality. In the event of transportation, we
recommend that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE TOOTHBRUSH AND ITS ACCESSORIES
A1 Toothbrush head*
A2 Ergonomically-shaped handle
A3 On/Off button of the toothbrush
A4 Button for setting the brushing mode
Depending on the selected mode, the
speed is set to 31000, 41000 or 48 000
vibrations per second.
A5 Brushing mode setting LED indicators
A6 Operation or charging of the
toothbrush LED indicator
A7 Charging stand
A8 Power cord
A9 Travel charger case without sterilisation
chamber
Supplied with model SOC 3200SL.
A10 Travel charger case with sterilisation
chamber
Supplied with model SOC 3210SL,
SOC 3311BK andSOC 3312WH.
A11 USB cable
*Note:
2 toothbrush heads are included.
DESCRIPTION OF THE TRAVEL CASE WITHOUT STERILISATION
CHAMBER
B1 Lid
B2 Toothbrush head storage space
One or two toothbrush heads can be
stored in this space.
B3 Toothbrush handle storage space
B4 Charging unit
B5 USB micro port
DESCRIPTION OF THE TRAVEL CASE WITH STERILISATION
CHAMBER
C1 Lid
C2 Toothbrush head storage space
C3 Sterilisation chamber
C4 Toothbrush head storage space
C5 Toothbrush handle storage space
C6 Charging unit
C7 USB micro port
ATTACHING AND REMOVING THE TOOTHBRUSH HEAD
■
Make sure that the toothbrush is turned off before attaching or removing atoothbrush
head A1.
■ Attach the toothbrush head A1 by sliding it on to the handle A2 from above.
■ Take off the toothbrush head A1 by pulling it away from the handle A2.
CHARGING THE TOOTHBRUSH
■ This toothbrush has abuilt-in Li-Ion battery that enables cordless operation.
■ Make sure that the toothbrush is turned off before charging it.
1. IN THE CHARGING STAND
■ Locate the charging stand A7 on an even and stable surface and plug the power cord A8
into apower socket (100–240 V).
■
Put the toothbrush on to the stand A7 from above, see figure D.When charging, LED indicator
A6 is lit red and LED indicators A5 gradually light up and turn off. When the battery is fully
charged, the LED indicator A6 will be lit blue and LED indicators A5 will turn off. After charging,
disconnect the charging stand A7 from the power socket.
Note:
Allow the toothbrush to charge for at least 15 hours before first use and after not
using it for along time.
If you are charging the toothbrush for the first time or if you have not used it for
along time, it may take up to 10 minutes before the LED indicator A6 lights up.
■ Afully charged toothbrush will provide approximately 180 hours of operation. If you brush
your teeth twice aday for 2 minutes, the toothbrush will last for 45 days without needing
to be recharged.
2. IN THE TRAVEL CHARGER CASE
■ Place the travel case A9 or A10 on adry even surface. Open the lid B1 or C1 and insert the
toothbrush handle A2 into space B3 or C5 so that the end of the charging unit B4 or C6
slides into the toothbrush handle A2. The lid B1 or C1 may be left open or it may be closed.
■
To supply power to the charger case A9 or A10 from an external USB interface, e.g. your
computer, powerbank, etc., connect the USB micro port B5 or C7 to an external USB interface
using USB cable A11.
■
When the travel case A9 or A10 is connected to acharging power source, the charging process
will start. With travel case A10, which is fitted with asterilisation chamber C3, you may sterilise
the toothbrush head A1 during the charging process. Sterilisation may only be performed
with the lid C1 closed. More detailed information about using the sterilisation chamber C3
is provided in chapter Toothbrush head sterilisation.
■
After finishing charging, disconnect the travel case A9 or A10 from the external USB interface.
HOW TO ACHIEVE THE LONGEST POSSIBLE BATTERY LIFETIME
■ To ensure the longest possible lifetime of the battery, we recommend:
– store, use and charge the battery at room temperature. Excessively high temperatures
may negatively affect its lifetime.
– do not unnecessarily leave the battery fully charged or completely flat for too long.
– do not keep the battery permanently fully charged.
– do not fully discharge the battery.
USING THE TOOTHBRUSH
■
Make sure that the toothbrush is properly assembled before using it. Wet the toothbrush
bristles with water and apply the toothpaste.Turn on the toothbrush by pressing button A3.
1. CORRECT BRUSHING TECHNIQUE
■ We recommend to start by brushing the right half of the upper dental arch from the outer
side. When brushing, proceed from back to front. Place the toothbrush bristles on to the
teeth at an angle of 45° in line with the gum, see figure E. Using short slow motions, move the
toothbrush to the other teeth. Once the outer side of the upper right dental arch is brushed,
move the toothbrush to the inner side of the dental arch. Again, proceed from back to front.
Adjust the toothbrush angle to the tooth arrangement.When brushing the inner side of the
front teeth, hold the toothbrush handle A2 vertical so that the tip of the toothbrush head
A1 points upwards. Finally, brush the upper tooth surfaces.
■
In the same way, brush the right half of the lower dental arch, the left half of the lower dental
arch and finally also the left half of the upper dental arch. When brushing the inner side of
the front teeth of the lower dental arch, hold the toothbrush handle A2 vertical so that the
tip of the toothbrush head A1 points downwards.
2. SETTING UP THE BRUSHING MODE
■
Repeatedly press button A4 to switch between the modes: CLEAN (standard brushing),WHITE
(whitening), POLISH (polishing), MASSAGE (massaging) and SENSITIVE (gentle brushing).
LED indicator A6 is lit during operation. The mode setting is indicated by the respective LED
indicator A5.The last setting is saved to memory. This means that the next time the toothbrush
is started, it will run in the mode that was set previously.
■
CLEAN mode is intended for standard tooth brushing. WHITE mode is intended for more
intensive tooth brushing (whitening). POLISH mode is intended for tooth polishing. MASSAGE
mode is acombination of tooth brushing and gum massaging. SENSITIVE mode is intended
for brushing sensitive teeth.
3. 4PACER FUNCTION
■
The toothbrush has atimer function that momentarily pauses the toothbrush every 30 seconds
until it turns off automatically, thereby informing the user that it is time to start brushing
the next part of your teeth. This will ensure that all the dental quadrants are brushed for
the same amount of time.
4. AUTOMATIC SHUT-OFF TIMER
■
The automatic shut-off timer automatically turns the toothbrush off after 2 minutes of
operation.This is the tooth brushing time recommended by dentists for the sonic toothbrush.
■
When the toothbrush is turned off, the LED indicators A5 and A6 will flash afew times
and then turn off.
■ When you have finished using it, make sure that the toothbrush is turned off and clean it
according to the instructions contained in chapter Cleaning and maintenance. Then put it
back on to the charging stand A7 or into the case A9 or A10. Before putting it into the case,
it is necessary to remove the head A1 from the toothbrush handle A2.
CLEANING AND MAINTENANCE
■ For hygiene reasons, regularly clean the toothbrush after every use.
■ Make sure that the toothbrush is turned off before cleaning it.
■
Thoroughly rinse the toothbrush head A1 under lukewarm running water to remove
any toothpaste or other remains. If whitening pastes are used when brushing teeth, it is
recommended to apply adrop of soap on to the toothbrush head A1 and then thoroughly
wash it under running lukewarm water. Remove the toothbrush head A1 from the handle
A2 at least once per week and clean it under running water in the location where it is
attached to the handle A2.
■ Rinse the toothbrush handle A2 under running lukewarm water and then dry it.
■
In the event that the charging stand A7 is soiled, wipe it with aclean dampened cloth and then
wipe dry. Ensure that the power plug contacts do not come into contact with water or moisture.
■
You may wipe the travel case A9 or A10 using adry or alightly dampened cloth and then dry
it carefully. Do not spray the travel case A9 or A10 with water, do not rinse it under running
water or submerge it in water.
■ For cleaning, do not use abrasive cleaning products, thinners, etc. Otherwise the surface of
the appliance may be damaged.
