Sencor SHI 5600GD Repair manual

06/2019- 1 -Copyright © 2019, Fast ČR, a.s.
EN Hair iron
Translation of the original manual
SHI 5600GD

06/2019- 2 -Copyright © 2019, Fast ČR, a.s.
EN Hair iron
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
General warnings
■This appliance may be used by children 8 years of
age and older and by persons with physical or mental
impairments or by inexperienced persons, if they are
properly supervised or have been informed about how
to use the product in asafe manner and understand the
potential dangers.
■Children must not play with the appliance.
■Cleaning and maintenance performed by the user must
not be performed by unsupervised children.
■In the event that the power cord is damaged, have it
repaired at a professional service centre to prevent
causing adangerous situation. It is forbidden to use the
appliance if it has adamaged power cord.
Warning:
Do not use this appliance in the vicinity of water.
Warning:
Do not use this appliance near baths, showers,
washbasins or other containers containing water.

06/2019- 3 -Copyright © 2019, Fast ČR, a.s.
■When using the appliance in the bathroom, unplug it
from the socket after use by removing the plug from
the socket, as the vicinity of water poses adanger, even
when the appliance is turned off.
■To ensure additional safety, it is recommended to install
an Residual Current Device (RCD) into the electric circuit
to the bathroom with a maximum current rating of
30mA. Ask an electrician for advice.
Electrical safety
■ Before connecting this appliance to apower socket, make sure that the voltage stated on its rating label corresponds to the voltage in your power socket.
■ Connect the appliance only to aproperly grounded socket. Do not use an extension cord.
■ Do not disconnect the appliance from the power socket by pulling on the power cord. This could damage the power cord or the power socket. Disconnect the power cord from
the power socket by pulling on the plug.
■ Do not place the power cord of the appliance over sharp objects. Make sure that the power cord does not hang over the edge of atable and that it is not touching aheated or
hot surface. Do not place the power cord in the vicinity of hot surfaces.
■ Do not wind the power cord around the appliance. Regularly check the power cord for signs of damage.
■ Keep the power cord dry.
■ Never use the appliance if you have wet hands or feet. Do not connect and disconnect the power cord to and from the power socket with wet hands.
■ Do not uncover the electrical parts of the appliance. They do not contain any components repairable by the user. Have the appliance serviced by qualified persons.
■ To avoid potential injury by electrical shock, do not spray the appliance or its power cord with water and do not submerge it in water or any other liquid.
■ Do not use the appliance if it is not working correctly, if it has been damaged or has been submerged in water.
■ Always turn off the appliance and disconnect it from the power socket when you have finished using it.
■ To avoid the danger of injury by electrical shock, do not repair the appliance yourself or make any adjustments to it. Have all repairs or adjustments performed at an authorised
service centre. Tampering with the appliance during the warranty period may void the warranty.
Safety during use
■ This appliance is designed for use in households, offices and similar types of areas. Do not use it in industrial surroundings or outdoors or in rooms with high humidity, i.e.
laundries or bathrooms.
■ Do not use the appliance for any other purposes than those for which it was designed.
■ Only use the appliance with the original accessories from the manufacturer. Never use accessories, which have not been supplied with this appliance or which have not been
explicitly recommended by the manufacturer.
■ Do not expose the appliance to direct sunlight and do not place it near an open fire or appliances that are asource of heat, e.g. electric or gas stoves. Only store and use the
appliance away from flammable or volatile substances.
■ Only position the appliance on aclean, dry, horizontal and stable surface. Do not position the appliance on the edge of akitchen countertop or table, or use it on the drainboard
of akitchen sink. Likewise, do not place it on window sills.
■ Do not place any items on to the appliance and do not step or sit on it.
■ Do not use the appliance in an excessively dusty environment.
■ The appliance must not be used for styling wigs, hairpieces or synthetic hair.
■ Protect the appliance against being dropped on the floor or table, even from low heights and against items falling on it.
■ When the appliance is running, watch out for children and household pets.
■ Never leave the appliance in operation without supervision.
■ If the appliance is operating or has not fully cooled down, do not place it on soft underlays (e.g. carpets, bed linen, towels, etc.) and never cover it.
■ When the appliance is used in the vicinity of children, pay increased attention and always place the appliance out of their reach.
■ Do not place any paper or plastic items between the arms of the appliance.
■ Prevent the appliance from coming into contact with skin.
■ Never use the iron on synthetic hair or animal fur.
■ Do not carry the appliance when it is hot.
■ Always turn off the appliance and disconnect it from the power socket when not using it, when not planning on using it and when leaving it without supervision, before cleaning
or moving it.
■ Thoroughly clean dust, fats and hairdressing agents (e.g. gels, mousse, sprays, etc.) from the plates after each use – these lower the performance and lifetime of the plates.
■ Never wash the appliance under running water or submerge it in water or another liquid. No part of this appliance is designed to be washed in adishwasher.
■ Before storing always allow the appliance to fully cool down.

06/2019- 4 -Copyright © 2019, Fast ČR, a.s.
SHI 5600GD
A
12
11
13
14
15
B
2
3
4
5
1
6
16
2
13
4
5
7
6
8
9
10
A

06/2019- 5 -Copyright © 2019, Fast ČR, a.s.
A
12
11
13
14
15
B
2
3
4
5
1
6
16
2
13
4
5
7
6
8
9
10
B
C
C

- 6 - 06/2019Copyright © 2019, Fast ČR, a.s.
EN Hair iron
User'smanual
■ Prior to using this appliance, please read the user'smanual thoroughly, even in cases,
when one has already familiarised themselves with previous use of similar types of
appliances. Only use the appliance in the manner described in this user’smanual.
Keep this user'smanual in asafe place where it can be easily retrieved for future use.
In the event that you hand this appliance over to somebody else, make sure to also
include this user'smanual.
■ We recommend saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for at least the
duration of the legal liability for unsatisfactory performance or quality. In the event
of transportation, we recommend that you pack the appliance in the original box
from the manufacturer.
■ Carefully unpack the appliance and take care not to throw away any part of the
packaging before you find all the parts of the appliance.
DESCRIPTION OF THE APPLIANCE AND ACCESSORIES
A1 Ironing plates
A2 Attachment mounting grooves (on
both sides of the iron)
A3 Anti-slip plate
A4 Display
A5 Increase temperature button
A6 Decrease temperature button
A7 Main power switch
A8 Arm lock
A9 Swivel power cord end
A10 Hanging loop
A11 Brush attachment
A12 Comb attachment
A13 Hair oiling attachment
A14 Hair undulation attachment
A15 Cleaning cloth
A16 Bottle with hair oil
B1 Attachment unit
B2 Slide-out hair oil tank
B3 Plug
B4 Filling opening
B5 Maximum oil level
B6 Optimal oil level
PURPOSE OF USE AND FEATURES OF THE HAIR IRON
■ The hair iron is intended exclusively for straightening, undulating and styling
human hair. It must never be used for styling wigs, hairpieces, synthetic hair or for
straightening animal fur.
■ The iron is equipped with an automatic safety shut-off function, that turns it off after
60minutes of inactivity.
■ The surface of the ironing plates is coated with titanium and enables operating
temperatures from 100 °C to 230 °C. The temperature can be controlled in
10°Cincrements.
APPLICATION
TURNING ON AND SETTING THE TEMPERATURE
■ Connect the iron to apower socket. The display A4 will show OFF.
■ Press button A7. The appliance will beep, the default temperature of 180°C will be
lit on the display and the iron will start heating up.
■ The temperature can be adjusted in 10-degree increments in the range from
100°Cto 230°Cusing buttons A5 (+) andA6 (-).
■ Holding down button A5 (+) for longer than 3 seconds, will automatically skip to
atemperature of 230°C.
Note:
If "888" appears on the display, this indicates that there is amalfunction of
the heat sensor or iron. If this happens, disconnect the iron from the power
grid and contact aservice centre.
TEMPERATURE LOCK FUNCTION
■ This function prevents accidental changes to the temperature while the iron is being
used. Activate the function by holding down button A6 for longer than 3seconds.
The text LOC will appear on the display and the set temperature will be locked, i.e.
no button will react when pressed.
■ Deactivate the function by holding down button A6 for longer than 3seconds. The
text LOC will disappear.
AUTOMATIC SHUT-OFF FUNCTION
■ If no action is taken after turning on the iron, i.e. no button is pressed, then for safety
reasons, the iron will turn off automatically after 60minutes of inactivity. It will start
again after button A7 is pressed.
Attention:
The automatic shut-off is intended only for cases, where you
forget to turn off the iron using button A7. Do not use the
automatic shut-off to intentionally turn off the iron.
TEMPERATURE DEPENDING ON HAIR TYPE
■ The suitable temperature for straightening hair depends on the hair structure.
Depending on the type of hair, an incorrectly selected temperature may cause the
hair to dry out, become brittle or in the worst case to burn. Therefore, first try ironing
at alow temperature (100°C) and set ahigher temperature only when necessary.
■ The information contained in the following table is for reference purposes only. It
may differ depending on hair type.
Hair type Temperature
Fine, damaged, discoloured, highlighted or dyed hair 100 °Cto 150 °C
Normal, lightly wavy hair 150 °Cto 190 °C
Very heavy, curly, unyielding hair 190 °Cto 230 °C
USING THE ATTACHMENTS
ATTACHING AND REMOVING THE ATTACHMENTS
■ Attachments A11 to A14 are an excellent aid for styling your hair and can be
combined as necessary.
■ Simply slide the selected attachment into the groove A2 in the arms of the iron all
the way in,see fig. C. ATTENTION – one type of attachment must always be inserted
on the same side of the iron, i.e. the top and bottom attachment must correspond.
The only exception are attachments A14, which are inserted into the grooves so that
they cover the top side of each arm of the iron.
■ After use, simply slide the individual attachments out of the grooves A2.
Attention:
Argan oil can only be used according to the procedure
described in this user'smanual.
Only apply argan oil to hair using the tank in the attachment,
never apply it directly.
USING THE HAIR OILING ATTACHMENT
■ The hair oiling attachment A13 consists of aholder B1 and aslide-out tank B2. To fill
the tank, it is necessary to slide it out of the holder.
■ Flip open the plug B3 and, through the filling opening B4, fill the tank with the
supplied argan oil or with your own hair oil with which you have the best experience.
It is not recommended to fill the tank up to mark B6.
Attention:
Prior to sliding attachments on or off, the iron must be turned
off and cooled down.
■ After filling the tank, thoroughly wipe away any spilled oil and slide it back into the
holder.
Note:
When storing attachments A13 with tanks containing oil, place them in
such away that the part with the filter from which oil comes out is pointing
upwards. Otherwise, oil will leak out and can soil the location where the
attachment is stored.
PROCEDURE FOR IRONING HAIR
■ Wash your hair thoroughly, dry it completely and brush through thoroughly so that
it is smooth and without knots.
■ Separate this prepared hair using clips into equally wide strands (about 5cm wide).
■ Start to iron the back part of the head at the lower strands of hair – at the root place
the strand of hair between the plates and gently press the handle of the iron. With
asliding motion pull the iron all the way to the ends of the hair.
■ Repeat the procedure for the same strand of hair until you achieve the desired
appearance.
■ Continue in the same way with the remaining strands of hair (first on the front part
of the head and ending at the sides).
■ Before the final combing, allow the hair to fully cool down.
Attention:
Do not touch the ironing plates or the attachments - there
is adanger of burns!
Do not leave the iron in the one spot for longer than
5seconds as hair could be burnt.
Use the iron only on healthy hair. Do not use the iron on oily,
stuck together or sweaty hair. On perm or coloured hair only
use the iron infrequently.
Tip:
Adjust the speed of movement of the iron on the hair strands according
to their character (fine hair is more sensitive to a hot surface and
requires asignificantly shorter ironing time than stronger hair).
TURNING OFF THE IRON
■ When you have finished ironing, turn off the iron by holding down button A7.
Abeep will be made and the display will show OFF.
■ Disconnect the iron from the power socket.
Attention:
Allow the iron and attachments to fully cool down before
storing!

- 7 - 06/2019Copyright © 2019, Fast ČR, a.s.
CLEANING AND MAINTENANCE
Attention:
Clean the ironing plates and attachments only after they
have fully cooled down!
No part of the iron may be submerged in water or washed
under running water!
■ To clean the outside parts of the iron and the ironing plates, use, for example, the
supplied cloth A15 dipped in lukewarm water. Do not use aggressive cleaning
agents, paint thinners or solvents. Using these solutions could damage the surface
of the product. The surface of the iron plates does not need any further cleaning.
■ Attachments can be cleaned under running water. Prior to storing or using them
again, allow them to dry completely or wipe them dry.
STORAGE
When not using the iron for an extended period of time, do the following:
■ Clean the iron as described in chapter Cleaning and maintenance.
■ Place the iron in asafe, dust-free, clean and dry place that is out of reach of children.
■ If you wish to secure the arms against opening, press button A8.
TECHNICAL SPECIFICATIONS
Rated voltage range .................................................................................................... 100−240 VAC
Rated frequency........................................................................................................................50/60 Hz
Rated power.......................................................................................................................................55 W
Temperature range.........................................................................................................100 to 230°C
Electrical shock protection class........................................................................................................ II
EXPLANATION OF TECHNICAL TERMINOLOGY
Safety class for electrical shock protection:
Class II – Electrical shock protection is provided by double or heavy-duty
insulation.
We reserve the right to change text and technical specifications.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. For proper disposal, renewal and recycling hand over
these appliances to determined collection points. Alternatively, in
some European Union states or other European countries you may
return your appliances to the local retailer when buying an equivalent
new appliance.
Correct disposal of this product helps save valuable natural resources
and prevents potential negative effects on the environment and human health, which
could result from improper waste disposal. Ask your local authorities or collection
facility for more details.
In accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
This product meets all the basic requirements of EU directives related to
it.