Sennheiser RS 135 User manual

Sennheiser electronic GmbH & Co. KG
Am Labor 1, 30900 Wedemark, Germany
www.sennheiser.com
Printed in China, Publ. 09/14, 560041/A01
Instruction manual
RS 135
UB_RS135-9_336x148_US_SP3_ganzeSeite.indd 1 19.08.2014 15:31:38

2
3
1
Rechargeable batteries
NiMH AAA 1.2 V
ON
OFF
VOLUME
4
5
6
ON
ON
Vol –
ON Vol +
OFF
Caractéristiques techniques / Specifications /
Technische Daten
Généralités / General / Allgemein
Plage de fréquences / Frequency
range / Frequenzbereich
926.15 MHz – 927.55 MHz
Nombre de canaux / No. of
channels / Anzahl der Kanäle
3
Émetteur TR 135 / Transmitter / Sender
Modulation / Modulation /
Modulationsart
FM, stereo
Alimentation / Power supply /
Stromversorgung
i/p: 100-240 V AC, 50-60 Hz, 0.1 A
o/p: 9 V DC, 0.34 A, 3.06 W
Consommation de courant / Power
consumption / Stromverbrauch
< 1.8 VA
Rapport signal/bruit / Signal-to-
noise ratio / Geräuschpegelabstand
> 65 dBA
Connecteur / Connector /
Anschlussstecker
RCA phono plug / 3.5 mm /
6.3 mm stereo
Poids / Weight / Gewicht 200 g
Dimensions / Dimensions /
Abmessung
85 mm x 225 mm x 133 mm
Récepteur HDR 135 / Receiver / Empfänger
Transducteur / Transducer
principle / Wandlerprinzip
open, dynamic
Couplage auriculaire / Ear
coupling / Ankopplung an das Ohr
supraaural
Réponse en fréquence / Frequency
response / Frequenzbereich
22 – 19,500 Hz
Impédance / Impedance /
Impedanz
24 Ω
DHT / THD / Klirrfaktor < 0.7 % at 1 kHz, 100 dB SPL
NPA / SPL / Schalldruckpegel 106 dB at 1 kHz, 1 Vrms
Alimentation / Power supply /
Stromversorgung
2 AAA batteries
Autonomie / Operating time /
Betriebszeit
approx. 20 hrs.
Poids / Weight / Gewicht 230 g
UB_RS135-9_336x148_US_SP3_ganzeSeite.indd 2 19.08.2014 15:31:39

2
3
1
Rechargeable batteries
NiMH AAA 1.2 V
ON
OFF
VOLUME
4
5
6
ON
ON
Vol –
ON Vol +
OFF
Caractéristiques techniques / Specifications /
Technische Daten
Généralités / General / Allgemein
Plage de fréquences / Frequency
range / Frequenzbereich
926.15 MHz – 927.55 MHz
Nombre de canaux / No. of
channels / Anzahl der Kanäle
3
Émetteur TR 135 / Transmitter / Sender
Modulation / Modulation /
Modulationsart
FM, stereo
Alimentation / Power supply /
Stromversorgung
i/p: 100-240 V AC, 50-60 Hz, 0.1 A
o/p: 9 V DC, 0.34 A, 3.06 W
Consommation de courant / Power
consumption / Stromverbrauch
< 1.8 VA
Rapport signal/bruit / Signal-to-
noise ratio / Geräuschpegelabstand
> 65 dBA
Connecteur / Connector /
Anschlussstecker
RCA phono plug / 3.5 mm /
6.3 mm stereo
Poids / Weight / Gewicht 200 g
Dimensions / Dimensions /
Abmessung
85 mm x 225 mm x 133 mm
Récepteur HDR 135 / Receiver / Empfänger
Transducteur / Transducer
principle / Wandlerprinzip
open, dynamic
Couplage auriculaire / Ear
coupling / Ankopplung an das Ohr
supraaural
Réponse en fréquence / Frequency
response / Frequenzbereich
22 – 19,500 Hz
Impédance / Impedance /
Impedanz
24 Ω
DHT / THD / Klirrfaktor < 0.7 % at 1 kHz, 100 dB SPL
NPA / SPL / Schalldruckpegel 106 dB at 1 kHz, 1 Vrms
Alimentation / Power supply /
Stromversorgung
2 AAA batteries
Autonomie / Operating time /
Betriebszeit
approx. 20 hrs.
Poids / Weight / Gewicht 230 g
UB_RS135-9_336x148_US_SP3_ganzeSeite.indd 2 19.08.2014 15:31:39

1
Package contents
HDR 135 headphones
TR 135 transmitter with
audio connection cable
NT9-3A power supply unit (US version)
NiMH rechargeable batteries, AAA size, 1.2 V
Adapter, 2 RCA sockets to 3.5 mm jack plug
Adapter, 1/4“ (6.3 mm)
Manual Instruction manual
Safety Guide

2
The diagrams corresponding to the chapter
headings can be found on the fold-out page.
Preparing the transmitter for use
The transmitter is prepared for wall mounting (recess at the
rear of the transmitter). The required mounting material
(screws and plugs) is not included in the delivery.
1
Connecting the transmitter to an audio output of
your audio source
왘Choose a suitable place near your audio source (e.g. TV,
stereo or home cinema system). Avoid placing the trans-
mitter close to metal objects such as shelf bars, rein-
forced concrete walls, etc. as this can decrease the trans-
mitter’s range.
왘Connect the transmitter‘s audio connection cable:
• directly to the RCA sockets (outputs) of your audio
source, making sure to connect the red RCA plug to the
red RCA socket R, or
• to the supplied RCA/3.5 mm adapter for connection to
a 3.5 mm headphone socket, or
• to the supplied RCA/3.5 mm adapter and 1/4“ (6.3 mm)
adapter for connection to a 1/4“ (6.3 mm) headphone
socket.
왘Set the volume for the headphone output of your audio
source to a medium level. If the headphone output volu-
me is set too low, the transmitter automatically switches
off.
Some TVs have a function that mutes the TV loud-
speakers when you connect a transmitter. If neces-
sary, change this setting via the operating menu of
your TV.
Connecting the transmitter to the power supply system
왘Connect the power supply unit to the socket at the rear
of the transmitter. Plug the power supply unit into a wall
socket. The transmitter switches on and the ON/OFF LED
lights up green.

3
Preparing the headphones for use
2
Opening the battery compartments
왘Turn the ear pads in the direction of the arrow until you
overcome a slight resistance and lift them off the ear
cups.
3
Inserting and replacing the rechargeable batteries
CAUTION
왘Only use NiMH rechargeable batteries, never
use standard batteries!
왘Insert the supplied rechargeable batteries. Secure the ear
pads to the ear cups.
왘Charge the rechargeable batteries for at least 24 hours
prior to first time use. Subsequent charging time de-
pends on the previous operating time and is up to
18 hours max.
왘Place the headphones on the charging cradle of the trans-
mitter. The red CHARGE LED lights up, indicating that the
batteries are being charged. The CHARGE LED remains lit
even when the rechargeable batteries are fully charged.
Using the headphone system
4
Switching on the audio source
왘Switch on the audio source. The transmitter automatical-
ly switches on and off together with the audio source. The
ON/OFF LED lights up green.
5
Switching on the headphones/adjusting the volume
왘First, set the volume on the headphones to a low level.
왘Switch on the headphones and set the volume to the de-
sired level.
왘Switch off the headphones after use to avoid discharging
the batteries.

4
6
Optimizing the reception
왘Adjust the receiver channel with the TUNE control on the
headphones.
However, if reception is subject to interference:
왘Change the transmission channel by setting the switch at
the bottom of the transmitter to another position and re-
adjust the receiver channel with the TUNE control on the
headphones. Some electronic devices (e.g. televisions)
can cause interference to your wireless headphone sys-
tem. If this happens, increase the distance between the
transmitter and the interference source.
Specifications and additional information
왘Specifications are included on the inside
cover page.
왘Visit our website at www.sennheiser.com.

5
Manufacturer declarations
Warranty
Sennheiser electronic GmbH & Co. KG gives a warranty of
24 months on this product.
For the current warranty conditions, please visit our website
at www.sennheiser.com or contact your Sennheiser partner.
Before putting the device into operation, please observe the
respective country specific regulations!
Statements regarding FCC and Industry Canada
FCC Declaration of Conformity (DoC)
We, Sennheiser Electronic Corporation
One Enterprise Drive • Old Lyme •
CT 06371 • USA
Tel: [phone]
Fax: [phone]
declare the above device comply with the requirements of Federal Communications Commission.
This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: Greg Beebe
SENNHEISER
Model No:
RS 135
This device complies with Part 15 of the FCC rules and RSS-
210 of Industry Canada. Operation is subject to the follow-
ing two conditions: 1) This device may not cause harmful in-
terference, and 2) This device must accept any interference
received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules and RSS-210 of Industry Canada. These lim-
its are designed to provide reasonable protection against
harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency en-
ergy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television

6
reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit diffe-
rent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
Changes or modifications made to this equipment not ex-
pressly approved by Sennheiser electronic Corp. may void
FCC authorization to operate this equipment.
CAN ICES-3 (B)/NMB-3(B)
RF Radiation Exposure Information
Since the radiated output power of this device is far below
the FCC / IC radio frequency exposure limits, it is not subject-
ed to routine RF exposure evaluation as per Section 2.1093
of the FCC rules and RSS-102 of Industry Canada.
This device meets FCC/ IC RF exposure guidelines for an
uncontrolled environment. The transmitter of this device
should be installed and operated at least 20 cm away from
the user’s body. Use of other accessories not verified by the
manufacturer may not ensure compliance with FCC / IC RF
exposure guidelines.
This transmitter must not be co-located or operated in con-
junction with any other antenna or transmitter.
In compliance with:
USA
FCC ID: DMORS03ABUS
Canada IC: 2099A-TR120II CAN ICES-3 (B)/NMB-3(B)

2
3
1
Rechargeable batteries
NiMH AAA 1.2 V
ON
OFF
VOLUME
4
5
6
ON
ON
Vol –
ON Vol +
OFF
Caractéristiques techniques / Specifications /
Technische Daten
Généralités / General / Allgemein
Plage de fréquences / Frequency
range / Frequenzbereich
926.15 MHz – 927.55 MHz
Nombre de canaux / No. of
channels / Anzahl der Kanäle
3
Émetteur TR 135 / Transmitter / Sender
Modulation / Modulation /
Modulationsart
FM, stereo
Alimentation / Power supply /
Stromversorgung
i/p: 100-240 V AC, 50-60 Hz, 0.1 A
o/p: 9 V DC, 0.34 A, 3.06 W
Consommation de courant / Power
consumption / Stromverbrauch
< 1.8 VA
Rapport signal/bruit / Signal-to-
noise ratio / Geräuschpegelabstand
> 65 dBA
Connecteur / Connector /
Anschlussstecker
RCA phono plug / 3.5 mm /
6.3 mm stereo
Poids / Weight / Gewicht 200 g
Dimensions / Dimensions /
Abmessung
85 mm x 225 mm x 133 mm
Récepteur HDR 135 / Receiver / Empfänger
Transducteur / Transducer
principle / Wandlerprinzip
open, dynamic
Couplage auriculaire / Ear
coupling / Ankopplung an das Ohr
supraaural
Réponse en fréquence / Frequency
response / Frequenzbereich
22 – 19,500 Hz
Impédance / Impedance /
Impedanz
24 Ω
DHT / THD / Klirrfaktor < 0.7 % at 1 kHz, 100 dB SPL
NPA / SPL / Schalldruckpegel 106 dB at 1 kHz, 1 Vrms
Alimentation / Power supply /
Stromversorgung
2 AAA batteries
Autonomie / Operating time /
Betriebszeit
approx. 20 hrs.
Poids / Weight / Gewicht 230 g
UB_RS135-9_336x148_US_SP3_ganzeSeite.indd 2 19.08.2014 15:31:39

Sennheiser electronic GmbH & Co. KG
Am Labor 1, 30900 Wedemark, Germany
www.sennheiser.com
Publ. 06/15, 560041/A02
Notice d‘emploi
Instruction manual
Bedienungsanleitung
RS 135
UB_RS135-9_336x148_US_SP3_ganzeSeite.indd 1 19.08.2014 15:31:38