Sense SE-300-WT-HAND User manual

Wireless Microphones
Wireless Receiver

| PG 2
www.snapav.com
1-Year Limited Warranty
This Sense™ Product has a One-Year Limited Warranty. This warranty includes parts and labor repairs on all
components found to be defective in material or workmanship under normal conditions of use. This warranty
shall not apply to products that have been abused, modied, or disassembled. Products to be repaired under this
warranty must be returned to SnapAV or a designated service center with prior notication and an assigned return
authorization number (RA).
1
year
Table of Contents
1. Before You Get Started..................................................................................................................................................... 3
2. How It Works ........................................................................................................................................................................ 3
3. Compatible Accessories...................................................................................................................................................4
4. Rack Mounting ..................................................................................................................................................................... 5
5. Wireless Receiver................................................................................................................................................................6
6. WIreless Transmitter and Receiver Adjustments.................................................................................................... 7
7. Body-pack Transmitter ..................................................................................................................................................... 8
8. Lavalier Microphone...........................................................................................................................................................9
9. Headset Microphones...................................................................................................................................................... 10
10. Lavalier Microphone...........................................................................................................................................................11
11. Specifications ......................................................................................................................................................................12
Compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.
Caution:
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

Support: 866.838.5052
PG 3 |
Sense microphones deliver excellent sound reproduction when and where you need it most. Each micro-
phone and/or microphone accessory is designed for specific applications that serve multiple purposes,
so even if you don’t have each one of the microhpones or accessories listed, read through each descrip-
tion and you may find an idea or more helpful information that allows you to work smarter, not harder.
2. How It Works
1. Before You Get Started
There are just a few steps to take in order to have a proper setup with your Sense microphones.
Step 1. First, connect the wireless receiver to the mixer.
Step 2. Connect the two included antennas or add an antenna booster for installations where optimal
signal strength is necessary.
Step 3. Connect the power adapter to the receiver (included), and into a surge protected power outlet.
Step 4. The last necessary step is to match the frequencies on each transmitting device. This basic setup
can be repeated for multiple microphones and applied many times over.
3a
(optional)
3
4SE-300-WT-BODY
(optional)
SE-300-WT-BODY
Transmit audio from 1 or 2
channels up to 1500 feet
Handheld Mic
Distributed Audio System
Hands-free Mic
Transmitter
0 0 0 0 0
1 1 1 1 1
2 2 2 2 2
3 3 3 3 3
4 4 4 4 4
5 5 5 5 5
6 6 6 6 6
7 7 7 7 7
88888
9 9 9 9 9
10 10 10 10 10 +12+12 -12-12
00
0
1
2
3
4
5
6
7
8
9
10
OUTPUT LEVEL
SOURCE1
ECA-70MIXAMP-1-240
POWER
SOURCE2 SOURCE3 SOURCE4
ON
OFF
MIC1 MIC2 MIC3 MIC4 SOURCE BASS TREBLE
MASTER
The wireless receiver can be placed on a surface or mounted in a rack. The antennas can be mounted in
the front, rear, or extended with an antenna booster (sold separately) for wireless sound pick up from a
handheld microphone transmitter or a hands-free body pack (see below for full list of accessories). The
SE-300-WR-1CHD receives transmissions up to 1500 feet, then outputs into a distributed audio system.

| PG 4
www.snapav.com
SE-300-WT-BODY
Hand-Held Wireless Transmitter and Microphone
The SE-300-WT-HAND (sold separately) transmits connected micro-
phones via wireless signal in corporate presentations, houses of
worship, audio/video conferencing, and more. The hand-held wireless
transmitter includes colored endcaps, batteries, and a mic stand
adapter.
3. Compatible Accessories
Single Ear Headset Microphone
The SE-500-SEH-T (sold separately) is recom-
mended for speakers in corporate presentations,
houses of worship, audio/video conferencing, etc.
Double Ear Headset Microphone
For animated speakers, the stability and flexibility
of the SE-500-DEH-T (sold separately) is ideal for
use in corporate presentations, houses of worship,
audio/video conferencing, etc.
Lavalier Microphone
The traditionally worn SE-300-LAV-BLK (sold with
body-pack transmitter or sold separately) lavalier
microphone is perfect for corporate presentations,
houses of worship, audio/video conferencing, and
more.
Body-Pack Transmitter
Pair the SE-300-WT-BODY (sold separately) with any of the following three
Sense microphones to wirelessly transmit excellent sound reproduction
back to the wireless receiver. The hands-free body-pack tranmitter includes
batteries and a lavalier microphone.

Support: 866.838.5052
PG 5 |
Antenna Booster
Raise your signal strength by 10dB with the SE-ANT-BM. Mount
the antennas to a wall or ceiling for an even greater signal pickup.
Extend it further with the B-ANT-EXT-20M (also sold separately).
Single Rack Mount
The single rack mount is included with Wireless Receiver. Secure
the SE-300-WR-1CHD with 4 screws and secure the mount to the
rack with 4 more screws. If desired, thread the antennas to the
front rack ears.
Installation with Single Rack Mount
• Verify no cords are attached to the receiver. Turn over
the rack adapter and receiver. Insert the receiver into the
desired rack adapter slot.
• Align, insert, and thread 4 included M3 screws into the 4
mounting holes of the rack adapter and receiver.
• Mount the rack adapter to the rack by threading 4 M3 rack
screws (not included) into the rack holes.
4. Rack Mounting

| PG 6
www.snapav.com
Annotations
1. Power On/O switch
2. Up button (frequency adjustment)
3. Down button (frequency adjustment)
4. Set button (frequency adjustment)
5. LCD display
6. Volume control
7. DC socket for power adapter
8. AF output, 3mm jack socket (AF UNBAL.)
9. Balanced XLR socket
10. Antenna input socket
11. Antenna
12. AF signal level
13. RF signal level
14. Diversity display (A or B antenna)
15. Battery gauge of the transmitter
16. Channel Display
13
12
5. Wireless Receiver
Front Panel
13
12
Back Panel
14 15
16
LCD Display

Support: 866.838.5052
PG 7 |
The most important step is pairing the wireless receiver and transmitter’s frequency. The wireless
receiver, body-pack transmitter, and hand-held wireless transmitter’s setup menus function identically.
Each device has a SET, UP, and DOWN button to make adjustments to the frequency, group, sensitivity,
or pickup gain.
Frequency Pairing
Match the frequency on both the transmitter and the reciever for wireless communication.
• Push the SET button once to select between frequency / group / sensitivity / RF outputs.
• Push the UP or DOWN button to adjust the setting of a menu.
• Press and hold SET for 3 seconds to activate that frequency.
• Once you see “MHz” blinking, you are ready to select your desired frequency by using the UP and
DOWN buttons.
• Push SET again to save the setting.
Group Adjusting
Multiple microphones can transmit on the same frequency using matching groups.
• Press SET for 3 seconds, the group (G) will flash on the LCD display.
• Push UP or DOWN to select a desired group.
• Push SET again and the Channel (CH) will flash.
• Push UP or DOWN to select the desired channel.
• Push SET again to save the setting.
Sensitivity Adjusting
Optimize sound pick up by adjusting the sensitivity. Caution: Increasing sensitivity can cause system
feedback.
• Press the SET button twice to select the sensitivity by holding it down for 3 seconds, releasing, and
pressing again for 1 second. The display will show “Sensit”.
• Use the UP and DOWN buttons to make the necessary adjustments.
• Push SET again to save the setting.
RF Outputs
To adjust the transmission gain, select between low or high. For extended battery life, select “rF Lo”.
• Push the SET button several times until the “rF Lo” or “rF Hi” flashes.
• Push UP to choose “Hi” for high transmitting power (50mW) and push DOWN to choose “Lo” for
transmitting power (10mW).
• Push SET again to save the setting.
6. WIreless Transmitter and Receiver Adjustments
SE-300-WR-1CHD SE-300-WT-BODY SE-300-WT-HAND

| PG 8
www.snapav.com
1
2
3
4
5
6
7
8
9
10
11
SE-300-WT-BODY
1. LCD display
2. Battery tray
3. Set button: set the
configuration of the
bodypack transmitter
4. Up button: To select settings
5. Down button: To select
settings
6. Power switch/mute
7. 4-pin Mini-XLR mic. input
8. Antenna
9. Belt Clip
10. Battery status display
11. Group & Channel
Features
The SE-300-WT-BODY transmits sound via wireless signal used for corporate presentations, houses of
worship, audio/video conferencing, video, film and sound reinforcement, or other applications where
low-profile, discreet placement is preferred.
• Phase-locked Loop (PLL) synthesized tuner ensures reliable performance
• Powered by 2 x AA batteries with 12 hrs. battery life
• Equipped with 4-Pin Mini XLR connector
• LCD display with channel and battery life indicator
• The “lock-on” function prevents tampering and RF interruption
• Extended dynamic range and smooth frequency response
Installation Tips & Guidelines
After placing batteries inside the SE-300-WT-BODY and attaching the microphone, pair the wireless
frequency with the wireless receiver. Refer to section 5 for full instructions on how to pair the frequency.
Annotations
7. Body-pack Transmitter (Sold Separately)

Support: 866.838.5052
PG 9 |
1
2
3
1. LCD Panel
2. Main display
3. Battery Indicator
Open the bottom of the microphone to access the LCD panel.
Features
The SE-300-WT-HAND transmits connected microphones via wireless signal and is typically used for
corporate presentations, houses of worship, audio/video conferencing, video, film and sound reinforce-
ment, etc.
• Phase-locked Loop (PLL) synthesized tuner ensures reliable performance
• Powered by 2 x AA batteries with 12 hrs. battery life
• LCD display with channel and battery life indicator
• Advanced circuitry ensures stable signal transmission
• Extended dynamic range and smooth frequency response
• Noise mute and tone-key squelch
• Internal antenna design
Installation Tips & Guidelines
To place or replace batteries inside the SE-300-WT-HAND by taking the following steps.
Annotations
Loosen the microphone head
counter-clockwise.
Push both battery tray buttons
to release the battery.
Insert 2 AA batteries.
Push the battery tray
back into the housing.
Thread the microphone
back on by twisting the
head clockwise.
Once you have re-attached the microphone head, pair the wireless frequency with the wireless receiver’s
frequency. Refer to section 5 for full instructions on how to pair the frequency.
8. Handheld Microphone (Sold Separately)
SE-300-WT-HAND

| PG 10
www.snapav.com
• Adjust the gooseneck of
the mic so that it is about
1/2” away from the mouth.
• Do not bend the boom
past a 20° angle.
Sense attachable headset microphones have an intuitive installation and work great for corporate
presentations, houses of worship, audio/video conferencing, and other applications where low-profile,
discreet placement is preferred.
• Connect the 4 pin mini-
XLR cable into the “MIC
IN” of the body pack.
• Attach the detachable
cable clip to wherever
feels comfortable, such
as your back or collar,
keeping the cord out of
the way.
Installation Tips & Guidelines
Features
• Low-profile design provides unobstrusive
pickup
• Durable, flexible material allows for custom fit
• Highly sensitive, omni-directional capsule
• Natural skin tone blends in seamlessly
• Collar clip adds stability
9. Headset Microphones
Single Ear Headset Microphone
To countour the Single Ear Headset Microphone
for your face, gently bend the earpiece into a
shape that securely grasps the ear. Then gently
bend the boom so that it follows the face and the
microphone is positioned close the the mouth.
Double Ear Headset Microphone
To contour the Dual Ear Headset Microphone for
your face, you will need to adjust the size and bend
it into the proper shape. Loosen the adjustment
screws, pull the headset to the correct size, then
re-tighten the screws to lock the positions in
place. Next, gently bend the headset in various
locations to create the ideal fit.

Support: 866.838.5052
PG 11 |
• Attach lavalier microphone to a tie, lapel, or whereever is suitable and about 6-10” away from your face.
• Plug the female, 4-pin mini-XLR cable connector into the “MIC IN” of the body pack.
Installation Tips & Guidelines
Features
Sense lavalier microphones have an intuitive installation and work great for corporate presentations, houses
of worship, audio/video conferencing, video, film and sound reinforcement, and other applications where
low-profile, discreet placement is preferred.
• Low-profile design provides unobtrusive pickup
• Omni-directional pickp pattern for various appli-
cations
• Wide dynamic range and frequency response for
excellent sound reinforcement
• Included clip for securing to clothing.
10. Lavalier Microphone (included with Body-Pack)
Important Note: Due to the distance between the talker’s mouth and the microphone, lavaliere micro-
phones are not designed for use in spaces where the talker is being reinforced in the same room - such
as training rooms. Using them in these applications will often result in feedback due to the higher gain
necessary for proper pickup. For these applications, the single ear hook and double ear hook micro-
phones are recommended.

| PG 12
www.snapav.com
11. Specifications
Rev: 150127-1545
SE-300-WR-1CHD
Frequency Preparation PLL Synthesized Control
Carrier Frequency Range 502-960 MHz
S/N Ratio >105dB
T.H.D <0.6%@1KHz
Audio Output Level -12dB
Controls Power On/O, Frequency Up/Down, Lock-on,
AF Output Impedance 600Ω
Squelch Pilot Tone & Noise Mute
Operation Voltage 12-18 VDC, 200mA
Output Connector 1 XLR Balanced Socket
1/4" unbalanced phone jack
Dimensions 212.3mm(W) * 38.3mm(H) * 144mm(D)
Antennas Dual Half-wave
Included Accessories 1U Rack Ears w/ Antenna Mounts, Power Supply
SE-300-WT-BODY SE-300-WT-HAND
Frequency Preparation PLL Synthesized Control PLL Synthesized Control
Carrier Frequency Range 502-960 MHz 502-960 MHz
RF Outputs 10mW / 50mW 10mW / 50mW
Output connector 4-pin mini-XLR (M) -
Stability ±10KHz ±10KHz
Frequency Deviation ±48KHz ±48KHz
LCD Display Frequency, Battery Level, Sensitivity Frequency, Battery Level, Sensitivity
Controls Power On/O, Mode Setting, AF Level,
Frequency Up/Down, Lock-on Mode
Power On/O, Mode Setting, AF Level,
Frequency Up/Down, Lock-on Mode
Spurious Emissions <50 dBC <50 dBC
Audio Frequency Response 50-18,000 Hz 50-16,000 Hz
Battery (2) AA 1.5V (2) AA 1.5V
Included Accessories Lavalier Mic, Batteries Colored Endcaps, Batteries, Mic Stand
Adapter
SE-500-SEH-T, SE-500-DEH-T SE-300-LAV-BLK
Connector 4-pin mini-XLR (F) 4-pin mini-XLR (F)
Frequency Response 60-15,000Hz 60-15,000Hz
Polar Pattern Omni-directional Omni-directional
Sensitivity (at 1KHz) -64±3 dB* (0.63mV) -60±3 dB* (1mV)
Impedance 1.8kΩ2.2kΩ
Max. SPL for 1% THD 130dB 130dB
SE-ANT-BM
Carrier Frequency Range 470-870 Mhz
Antenna Gain 1.8 dBi
Booster Gain 10 (+2, -1) dB
Coverage Angle 360°
Operation Volate 12-18v
Rating Indoor/Outdoor (not waterproof)