Sunway WSU43 User manual

User Manual
WSU43
Wireless solar rear view system
SUNWAYI
100% DIY, intalls in minutes
User Manual
Version 1.0 (neutral)
NO DRILLING / NO SPLICING
No Wire / All-i n-One
Wireless
Solar Charging
Wire le ss Sola rP ower Re ar Vi si on
Low Pow er Consum ption

INTRODUCTION
Welcome
Thanks for your choosing WSU43 product, which provides
value and quality. Please read this User Manual carefully
before using the product.
Wireless SolarPower RearVision can display image behind
the vehicle and can be used when backing up or any time you
want to view behind the vehicle (even while your vehicle is in
park).
TABLE OF CONTENT 01. CONPONENTS
1. All-in-one camera with built-in battery and solar panel
2. 4.3 inch monitor
4. power cord with a Touch 5. USB cord
6. screw & plate washer &
hex/nut (4pcs)
1 2
Table of Content
01 Components ----------------------------------------2
02 Getting Started ------------------------------------3
03 Installation ------------------------------------------4
04 Monitor Mount --------------------------------------5
05 Operation -------------------------------------------5
06 Buttons & Setting ----------------------------------6
08 Information ------------------------------------------9
09 Specification ---------------------------------------10
10 Disclaimer ------------------------------------------11
11 Warranty Info --------------------------------------12
12 Trouble Shooting ---------- -----------------------13
13 Care & Maintenance -----------------------------14
07 Interface Icon --------------------------------------8
Botton for Rearview (as
standby reversing trigger)
3. holder of monitor
7. Screw & Tool

02. GETTING STARTED
Remove the whole Wireless SolarPower RearVision WSU43
packing or assembly and make sure all components are
included.
4
Charge the All-in-one camera’s built-in battery
1. Connect the supplied USB cord to the micro USB port of the
All-in-one camera.
2. Plug the USB cable into any standard USB charger with an
output rating of 500mA or higher.
3. Charge 2 to 5 hours.
Under normal use, the All-in-one camera maintains a charge
with exposure to sunlight. A battery status indicator is provided
on the monitor when the camera is in use. If you’re storing your
vehicle in a garage ( or not exposing the camera to sunlight on
a regular basis) for more than one month, you may need to
recharge it via the micro USB port.
Camera Installation
1.
Check the wireless function
1. Shake the camera in the air.
2. Touch the Monitor buttom quickly and check the image after the
monitor is powered. Or touch the “Touch for Rearview”
button on the car charge adapter to trigger the monitor to work,
check the image after the monitor is powered.
03. INSTALLATION
3
Hex Nut PM6x30mm
Plate Washer ø13xM6x1mm X4
Hex/Nut(female)ø10xM6x5.8mm X4
A
B
C
110°
Note
All-in-one camera has to be waken up from sleeping status by little
vibtation.
*
In the process of use, there is wireless interference from outside.
If no connection normally, the device will shut off automatically 10 seconds
later. Then please touch the “Touch for Rearview” button go turn it on.
*
Camera Angle
To adjust the camera angle for ideal angle
if the default angle (such as position A) is not
good, just use your fingers to hold the camera
house and move the Lens to position B, position C,
or other angle.
70°
50°
90°
A
B
C
90°
55°
55°
B
Position
35°
145°
70°
55°
55°
A
Position
125°
15°
50°
50°
55°
C
Position
0°
105°
Note
Please note when rotating the lens: hold the license plate holder with one
hand, and the outer frame of the camera with the other hand and rotate up
or down to make the best Angle.
*

05. OPERATION
Using the RearVision WSU43
1. Switch your 12-volt DC power port on with your ignition, the monitor wil
start work accordingly, the video signal will be sent from camera and will
be displayed on the monitor.
The image is set to time out in 30 seconds. However if you wish to shut the image
off manually, just touch the “Touch for Rearview” Button on the monitor again
anytime to stop at once.
2. If you want to see the backup image when driving your car , just touch the
“Touch for Rearview” Button on the top of monitor (see figure 1), or touch
the “Touch for Rearview” button of the cigarette lighter adapter(see figure 2).
3. When the vehicle is shut off, power is removed from the monitor
and the monitor will shut off automatically, and the camera will
stop work.
Note:
After you have been staying inside vehicle quietly (eg. sleeping) with vehicle
engine stopping, you want to see the backup image but only put your
vehicle key on the ACC -ON position (no starting the engine), there will have
no image on the monitor after touching the starting button.
So you have to give the vehicle a light vibration (such as re-open and shut
vehicle door, or tap somewhere lightly), then touch “Touch for Rearview”
button to start work.
If you want the RearVision WSU43 to keep working after 30 seconds (for
example, you cannot finish reversing your vehicle during 30 seconds), you
have to touch the “Touch for Rearview” button on the monitor or the
cigarette lighter adapter for another 30 seconds.
*
*
6
05. OPERATION04. MONITOR MOUNT
1. Two way to mount the monitor
1) Stick on the dash board: Fix holder bracket A
(see figur 1) to the install position of monitor via
screw tool, choose and clean a right place on the
dash board, tear the paper of the monitor holder’s
sticky tape, put and press the holder on the dash
board.
2) Socket on the window shield: Fix holder bracket B
(see figur 2) to the monitor via screw tool, choose
and clean a right place on the window shield. With
the suction lever in the released position, press the
suction cup against the windshield. Press the suction
lever toward the suction cup to lock the mount.
To adjust the angle of monitor, loosen the collar on
the ball joint, retighten in the desired position.
06. BUTTON & SETTING
Function of the monitor backup buttons
1. The middle button:
Short Press to enter monitor menu setting.
Long Press (press and hold for 3 seconds) to confirm the chosen
item in the menu setting interface.
BUTTONS
5
Figure 2
Touch
for rearview
Figure 1
Touch
for rearview
2. Plug the monitor cigarette lighter, then socket power cord into a
12-volt DC power port.
Figure 1
Figure 2

87
2. The Up button:
Short Press to change/add parameter value at the menu
setting interface.
3. The Down button:
Short Press to change/decrease parameter value at the
menu setting interface.
Short Press DOWN button to switch the Parking Guide
Lines display modes (Display or No display).
Menu Operations:
While the monitor is showing the backup camera image, short press
the middle button to enter the main menu interface, and 4 options
are available (Including Pairing, Image Parameters, Image Mirror,
Software Information).
Image Parameters(Brightness, Contrast, Color) setting interface
are shown bellow:
Brightness/Contrast/Color settings are similiar. Take Brightness as
an example,when brightness is chosen, press UP or DOWN button
on the interface to adjust the brightness as shown bellow:
Select “Image Mirror”, press UP or DOWN button on the interface
to mirror the image.(It is best to have a video image displayed
when making this selection).
Select “Software Information”, press UP or DOWN button to display
the software version information.
10
06. BUTTON & SETTING 06. BUTTON & SETTING
Signal strength Solar charging
Camera battery capacity
Signal strength Solar charging
All-in-one Camera battery capacity
07. INTERFACE ICON
Notice:
All MENU adjustment needs to be completed within 30 seconds, otherwise
it will automatically shut down.
*

08. INFORMATION
109
09. SPECIFICATION
CAMERA
Operational Current(when transmitting): <280mA
Sleeping Current: <0.06mA
Pixels: 960×576
View Angle: 110˚
Image Sensor: 1/3'’ CMOS
Image Quality: Max 30 fps
Camera Assembly: IP 65
TRANSMITTER
Frequency: 2406 ~ 2475 MHz
Transmission distance: ˃328 ft. (˃100 m)
Working Temperature: 14˚~ 122˚F (-10˚~ 50˚C )
MONITOR
LCD Display Screen Size: 4.3 inches
Power Cord Fuse: 1A
Operation Current: <150mA
Effective Pixels: 480×272
Battery Icon is on the top right corner of the screen, indicates the
relative capacity of the built-in lithium battery of the All-in-one camera
when a video image is present.
Signal strength of the received image is on the top left corner of the
screen when a video image is present.
Red Indicator Light
When the monitor is powered on and still stay standby mode, the
Red indicator Light doesn’t work. When touching the
“Touch forReview” button, the Light will blink quickly.
When the monitor works, the light will extinguish.
All-in-one Camera
The Camera & Video transmitter are built-inside the US license plate,
and is equipped with the built-in rechargeable lithium battery, which
is connected with the solar panel.
A USB charging port is provided to charge the battery initially prior
to mounting on your vehicle, as well as to recharge if needed. When
charged fully, the battery will last for several months under average
use with NO SUNLIGHT (average use is defined as 5 times per day).
When the monitor is turned on, work command is sent to the camera,
upon receive this signal, the camera will work from standby mode at
once, and send image video to the monitor for 30 seconds.

10. DISCLAIMER 11. WARRANTY INFO
WSU43 Wireless SolarPower RearVision is intended to assist
responsible driver, but it doesn’t relieve a driver from full
responsibility for operation of the vehicle. It is the driver’s sole
responsibility to avoid contact with any objects, animals, especially
persons. By installing and/or using WSU43 Wireless SolarPower
RearVision, you agree that you are solely responsible for the
operation of your vehicle, the Rear Vision supplier is not
responsible for any property damage, personal injury, or loss of life
that may result from the operation of your vehicle.
All express or implied warranties for this product are limited to one
(1) year. The supplier is not liable for damage arising from the use,
misuse, or operation of product including but not limited to loss of
time, invonvenience, loss of use of your product property damage
caused by your product or its failure to work, or any other incidental
consequential damages including personal injury.
During the warranty period, defective units will be repaired or
replaced (with the same or a comparable model) at supplier’s
option, without charge to the purchaser with dated proof of
purchase. Units returned without dated proof of purchase will be
considered out of warranty, therefore are not covered by the
described Limited Warranty. We will not assume responsibility for
loss or damage incurred in shipping.
Service Under Warranty
Units will be repaired at “out-of-warranty” service rates when:
1. The unit’s warranty has expired.
2. A dated proof of purchase is not supplied.
3. The unit has been returned without its serial number.
4. The unit has been misused, abused, modified, installed
improperly, or had its housing removed.
Service Out-of-Warranty
WARRANTY INFO
WARRANTY INFO
WSU43 Wireless SolarPower RearVision product is warranted to
the original purchaser for a period of one(1) year from the date of
original purchase against all defects in materials and workmanship,
when purchased from a supplier. This limited warranty is void if the
unit is abused, misused, modified, installed improperly, or if the
housing and/or serial numbers have been removed. There are no
express warranties covering this product other than those set forth
in this warranty.
Notice:
Some USA states or local government may have regulations or laws
that restrict the use of anything that might impair the clear view of a
license plate. Check local laws for explanation.
*
1211

13. CARE & MAINTENANCE
12. TROUBLESHOOTING
♦ If the monitor doesn’t turn on when power is applied:
1. Check to make sure the power source is active (if your cigarette lighter is
switched with vehicle ignition, your monitor will only work when the vehicle
is running or the key in the ON position).
2. Check to make sure the fuse and power cord are in working order.
1. The battery in the camera may be depleted and require recharging.
♦ If the monitor doesn’t display images within a few
seconds of touching the starting button:
2. In the process of use, there is wireless interference from outside. so if you
can't turn on the product over 15 seconds after touching the botton , please
touch the Touch for Rearviw botton again to turn it on.
Check that the camera lens is clean from road grime, snow, or ice.
♦ If the video image is poor:
Recharge the battery in the camera.
♦ If the video image does not last 30 seconds:
Don’t clean or wipe the All-in-one Camera with solvents or
chemical materials. If necessary, remove dirt or stains using
a soft cloth dampened with a mild detergent solution.
Cleaning
Fuse Replacement
1. Turn the cap on the tip of the power plug counterclockwise
(no tools needed).
2. Remove the cap, center pin and fuse.
3. Replace the fuse with a new 1-am fuse.
4. Replace the center pin and cap. Turn the cap clockwise.
The Wireless SolarPower RearVision is designed to provide years
of service. The RearVision WSU43 should be recycled or safely
disposed of at a local recycling center.
Disposal
14
♦ If no image after touching “Touch for Rearview”Botton
in quiet (no vibration at all) environment, such as testing
the WSU43 in office or laboratory.
Vibrate the camera, touch the powered Monitor “Touch for Rearview” button
quickly (not over 3 minutes from vibration) to wake up the sleeping camera,
make it enter standby status and receive the command from the monitor.
Notice:
Under the actual situation of installation, test, and use of vehicle, the
environment is different totally. Little vibration must happen when open
vehicle door, people touching the vehicle, even the engine work.
So the camera will stay at standby status.
*
13

FCC Statement
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician
for help
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions (1)this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
15
14.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.