Sensio SE9072HD User manual

HD LED
LINKABLE STRIP
LIGHT - 600mm
CODE: SE9072HD
Components
Important safety information
Tools required
INSTALLATION
INSTRUCTIONS
IMPORTANT: please read these instructions before commencing installation and retain for future reference.
1 x SE9072HD LED
Linkable Strip Light
2 x Fixing Brackets
1 x Connector Cable
1 x Fitting Instructions
Please read these instructions carefully before attempting to install
this product. It is advisable to keep these instructions in a safe place
for further reference.
We recommend that you consult a qualified electrician.
All electrical installations must be carried out in accordance
with current IEE wiring regulations (BS7671).
These products must not be modified, if any modifications are
made, it may invalidate the warranty and may render the product
unsafe. These LED lights operate low voltage (24V).
Do not wire the individual LED light fittings directly to the mains.
This product is for indoor use only. Keep out of moisture and use
only in dry rooms.
• If in doubt installation must be carried out by a qualified
electrician.
• Install on smooth flat surface(s) only.
• The Wattage of this product is 7.1W. Make sure that
the LED driver used with these fittings has an adequate
max wattage.
• We recommend using the SE40555 15W 24V LED Driver with this
fitting. You will be able to run a maximum of 2 fittings per driver.
Alternatively, use the SE40556 30W 24V LED Driver. A maximum
of 4 fittings can be run from this driver.
Safety instructions
1. Before commencing installation or maintenance, isolate the main
electrical supply for the appropriate circuit at the fuse board.
2. This product requires a 24V LED driver which is only
suitable for connecting to a 240V 50Hz supply.
3. The light should be mounted onto a secure surface.
4. Position lights where they will not be exposed to steam
or splashes etc.
5. Suitable for furniture lighting.
6. When the lamp expires the fitting must be replaced.
7. Class III safety extra low voltage (SELV).
Waste Electrical & Electronic Equipment (WEEE)
The Symbol on the product, or on the document accompanying the product, the crossed out
wheelie bin symbol, indicated that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic waste.
Power DrillPZ1 Screw Bit10mm
Drill Bit
Pencil

Installation
Operation
Maintenance & Care
A. SE40520. The HD LED
Linkable Strip Light Sensor
Switch can be used as an
optional switching method
for the SE9072HD. The
light fittings then connect
back to the driver via the
sensor switch. Sold
separately.
HD LED LINKABLE
STRIP LIGHT - 600mm
• Ensure that the power is disconnected prior to cleaning.
• To keep the finish of this product, wipe over with soft cloth periodically.
• Do not use harsh chemical solvents, it may dis-colour or damage the finish.
7
Finally wire the LED driver to 240V mains supply
or 13A plug top.
5
Multiple SE9072HD fittings can be
interlinked together to form a continuous
run of light.
Once brackets are in place,
push the SE9072HD unit
into the brackets.
Connect the Lincus cable into the side of
the SE9072HD unit.
3 4
Screw brackets securely.
2
Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustration purposes only, Sensio has the right to change any information
without prior notice. Make sure you check all hole cut outs before work commences.
2
6
Plug the white connector on the end of the
Lincus lead into the 24V LED driver distributor
block. Beware not to exceed the wattage of the
LED driver, the max wattage will be displayed
on the 24V LED driver and on the light unit
fitting it will display the wattage requirement.
Mark-up and drill the holes in the
cabinet for the fixing brackets.
1
A