Sensio SE791090 User manual

1 x RGB
REMOTE
CONTROL
CODE: SE791090
INSTALLATION
INSTRUCTIONS
IMPORTANT: Please read these instrucons before commencing installaon and retain for furture reference.
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the crossed out wheelie
bin symbol, indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collecon point for the recycling of electrical and
electronic waste.
Components Tools required
1 x Remote Control 1 xRemote Holder 1 x adhesive pad Ruler Pencil Screw Driver Power Drill
Please read these instrucons carefully before aempng to install this
product. It is advisable to keep these instrucons in a safe place for
future reference.
We recommend that you consult a qualified electrician. All
electrical installaon must be carried out in accordance with
current IEE wiring regulaons (BS7671).
These pThese products must not be modified, if any modificaon are made, it
may invalidate the warranty and may render the product unsafe.
This product should be used indoors.
Important Safety Informaon
Safety Instrucons
• If in doubt installaon must be carried out by a qualified
electrician.
• Install on smooth flat surface(s) only.
• The SE791050 RGB receiver required to run this remote
control can be used with 24V RGB Flexible Strip only.
Maximum 60W. Do not exceed the maximum waage.
1. Before commencing installaon or maintenance, isolate the main electrical supply for the appropriate circuit at the fuse board.
2. This product should be mounted onto a secure surface.
3. Never exceed the total output of the LED driver used with your lights.
4. Suitable for furniture lighng.
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustraon purposes only, Sensio had the right to change any informaon without
prior noce. Make sure you check all hole cut outs before work commences.
REQUIRED:
1 x SE791050
RGB Receiver
2 x screws
1 x instrucons


 
D
•
•
1 x RGB REMOTE CONTROL

•
•
•
To match the slave receiver to the transmitter:
Connect the RGB Flexible strip cable to the
junction box on your receiver. 
Connect the JB4 connector of the receiver to
your driver, turn the power on and then
press the test button.
The indicator light will turn on. The remote will
exit the matc hing setting mode after 1 minute of
inactivity and the indicator light will turn off
 
  •
•
•
The light on the receiver will flash on and
off. Your remote and receiver are paired.
If the light does not flash, repeat step1 -5. 
To match a master receiver to the transmitter:
Revisit a central receiver which has already
been paired (power should be on & lights off) 
Press and hold the on/off button on the
remote control for 10-15 seconds.




•  � 
 

- 
Connect to the power and press the test
button for 5 seconds.
If the indicator light flashes after 5
second, your receiver is connected. If not,
please repeat steps 6-8.
Mount the holder for the controller onto the
wall using either screws or adhesive pads.
Then insert the controller into the holder. 
 


The transmitter
can control
multiple Receivers
within the remote
range of15m. 7 /
/�
I uo �/ • t

_
  / )
   I
 /�.
�/
Maintenance & Care
Ensure that the power is disconnected prior to cleaning.
To keep the finish of this product,wipeover with soft cl oth periodically.
Do not use harsh chemical solvents, this may discolouror damage the
finish.
Sensio House, Unit 7, Speedwell road, Whilwood, Castleford, West Yorkshire, WFlO 5PY
www.sensio.co. u k
-
Operating the Controller:
On/off: Press once to turn on, press
again to turn off. Colour wheel:
Rotate to select desired colour
fade mode button: The lamp colour
will gradually change.
Flash mode button: The lamp
colour will rapidly change
Memory function: When turned on,
the controller will return to
the last setting prior to shut off.
Brightness adjustment:Hold down
Fade mode button and rotate
colour wheel to change
brightness.
Colour change speed adjustment:
Hold down the Flash mode button
and rotate colour wheel clockwise
to decrease the colour change
speed, or turn anti clockwise to
increase the colour change speed.
Technical drawings for illustration purposes only. Sensio have the right to change any
information without prior notice. Make sure you check out all hole cut outs before work
commences.
