SES-imagotag Hermes RAN2.0 Assembly instructions

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
Hermes
RAN2.0
Hardware Installation Manual
Latest changes: 30.08.2021

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
Introduction
The Hermes RAN2.0 is a new Hermes design based on a 3-wire bus for power and data which
is built into an aluminium rail. Rail displays are using mechanical contact to connect to the
bus.
The Rail Controller includes a radio component to receive and send wireless transmissions to
the Access Point. The radio is based on Bluetooth Low Energy (BLE) technology and is
operating in the 2.4 GHz ISM band. The protocol implementation is called “RAN2.0”
Table of content
Introduction............................................................................................................................................. 2
Components ............................................................................................................................................ 3
Hardware Setup....................................................................................................................................... 4
Safe handling of lithium batteries........................................................................................................... 7

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
Components
•Rail - aluminium rail + 3-wire bus
•Rail Controller –“bridge” between radio and 3-wire bus of the rail
•Rechargeable battery pack
•Rail Displays –E-ink displays
•BLE Access Point –transmitter device
Figure 1 –Rail, Rail Controller, Rechargeable Battery Pack, Rail Displays
Figure 2 - Rail Displays
Figure 3 - Rail Controller & Rechargeable Battery Pack
Figure 4 - BLE Access Point

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
Hardware Setup
1) Plugging Rail Controller into Rail
Figure 5 - Plug Rail Controller into Rail
Figure 6 - Plugged Rail with Rail Controller

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
2) Supplying Rail with power (plugging Rechargeable Battery Pack)
Figure 7 - Rail with Rail Controller and Rechargeable Battery Pack
Figure 8 - Connect Rail with Rail Controller and Rechargeable Battery Pack
Figure 9 - After connecting, the LED of the Rail Controller flashes in green color

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
3) Plugging Rail Displays into the Rail
Figure 10 - Plugging Rail Displays into Rail
Figure 11 - Plugging Rail Displays into Rail
Figure 12 - LED of Rail Displays flashing green when a new Rail Display is plugged to the Rail

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
Safe handling of lithium batteries
•Li—ion Battery (18650) had passed the test UN 38.3 and are classified as non-
dangerous good.
•Do not allow undiluted product or large quantities of it to reach ground water course
or sewage system
•Auto-ignition temperature 130°C
•CB-test reports for used batteries and battery pack itself in progress.
Integrated battery overcharge / discharge protection circuits
WARNING:
Battery may explode or catch fire if misused.
Do not disassemble, incinerate, or expose to high temperature above 212°F (100°C).
Keep away from children.
For further information scan QR-code.
Certification
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION TO USERS
Changes or modifications not expressly approved by the party responsible for
compliance could void the user`s authority to operate the equipment.
FCC rules apply to the following products: HMS RD1/160 (Model: HRDX-0160-Y) , HMS
RD1/220 (Model: HRDX-220-Y), HMS RC1 (Model: HRCX-BT01-Y)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.

SES-imagotag GmbH I Kalsdorfer Straße 12 I A-8072 Fernitz/Mellach - AUSTRIA
FB: FN350927w I HG : Graz I UID : ATU65936017
T. [phone] I F. [phone] I E. [email protected] I www.ses-imagotag.com
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
L’metteur/rcepteur exempt de licence contenu dans le prsent appareil
estconforme aux CNR d’Innovation, Sciences et Dveloppement conomique
Canadaapplicables aux appareils radio exempts de licence. L’exploitation est
autoriseaux deux conditions suivantes:
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radiolectrique subi, mme si
lebrouillage est susceptible d’en compromettre le fonctionnement.
IC standards apply to the following products: HMS RD1/160 (Model: HRDX-0160-Y) , HMS
RD1/220 (Model: HRDX-220-Y), HMS RC1 (Model: HRCX-BT01-Y)