SHARKWARD Sk601A User manual
-3-
Microwave Sensor Microwave Sensor
SK601A instruction SK601A instruction
The light can be set to stay ON for any period of time between approx.10sec(turn fully
anticlockwise) and a maximum of 12min(turn fully clockwise). Any movement detected
before this time elapse will re-start the timer. It is recommended to select the shortest
Note: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period has
elapsed.
it fullyanti-clockwise to select dusk-to-dawn operation at about 10 lux. Turn it fully
clockwise to select daylight operation at about 2000lux. The knob must be turned fully
clockwise when adjusting the detection zone and performing the walk test in daylight.
10sec~12min
10~2000LUX
please do not adjust the sensitivity to maximum, to avoid the product does not
work normally caused by wrong motion.Because the sensitivity is too high easily
wrong motion by interference of power grid & electrical equipment.All those lead
the product does not work normally ! When the product does not work normally,please
try tolower thesensitivity appropriately, and then test it.
When use this product, please adjust the sensitivity to an appropriate position you need,
detect the wrong motion by wind blowing leaves & curtains, small animals, and the
Time setting
Light-control setting
The chosen light response threshold can be infinitely from approx. . Turn10~2000Lux
In different cases, the sensitivity of the lights has certain deviation.
time for adjusting the detection zone and for performing the walk test.
-4-
TROUBLESHOOTING
Malfunction Cause Remedy
wrong light-control setting selected Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
Check zone setting
the sensor not mounted for detecting
movement reliably
Securely mount enclosure
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
movement
rapid movements are being suppressed
to minimize
malfunctioning
the
zone you have set is too small
Check zone setting
detection
or
Note: please don’t adjust the three functional buttons to excess. That is because the three functional
buttons were connected to the components directly, there is a small stopper in each of
the three components, when you adjust the buttons from start to end, the excessive turn
will damage the stopper
，
and lead to the 360°non-stop turn around. The adjust range limit
is 270°, please do pay attention to this.
The load work without any
The load will not work despite
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
Warning !
1. Being installed in the rocking object will lead to misoperation.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed place.
The following situation will lead to misoperation
-2-
Warning!
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and
turn off the light automatically when you leave off. You can set the closing delay time to meet your needs.
For example, you may adjust the TIME knob to select the delay time 12min when you think you will come
back in 10mins. The TIME knob is as follow (Keep away from the detecting zone after adjusting the testing
time or that the detecting time will be inaccurate when any moving object is detected again by the product).
The product can not work normally if there is
metal material behind the Installed place.
LUX
SENS TIME
Microwave Sensor Microwave Sensor
SK601A instruction SK601A instruction
-1-
SK601A
If you want to detect small zone‚you can just adjust the sense knob SENS to the range that you
need (You may need to adjust some times untill you think it is suitable).If you want that the light can
be turned on when the circumstance luminance is under some value, you can just adjust the knob LUX
(The working luminance knob) to select the luminance value (You may need to adjust some times untill you
think it is suitable).
Detection range setting(sensitivity)
Detection range is the term used to describe the radii of the more or less circular
turn the detection control fully anticlockwise to select minimum detection range
(approx.1m radii), and fully clockwise to select maximum detection range (approx.
8m radii).
with middle figure and moves at a speed of 0.6~1.5m/sec. if person’s stature, figure and
moving speed change, the detection distance will also change.
1~8m
detection zone produced on the ground after mounting the sensor light at a height of 2.5m,
Note: the above detection range is gained in the case of a person who is between 1.6m~1.7m tall
Non-metal material
When the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
SENSOR INFORMATION
Height of installation2.5~3.5M
(Height of installation2.5M)
Min:1m
Max:8m
2.5-3.5m
Sensing distance adjustment range
Min:1m
Max:8m
UTILIZING FIELD AND INTRODUCTION
SK601A is a moving object sensor that can detect range of 360°and it’s working frequency is 5.8G.
The advantage of this product is stable working state (stable working temperature: -15°C~+70°C), SK601A
adopts a microwave sensor (high-frequency output <0.2mW), so that it is safe and performs better than
infrared sensor.
Sensing angle adjustment range
360
SPECIFICATIONS
Installation site:Indoors, ceiling mounting
HF system:5.8GHz CW radar, ISM band
Reach: 1-8m(radii.) adjustable
Time setting:10 sec. to 12min.
Light contro:10~2000Lux
Power consumption:approx.0.9W
Transmission power ：<10mW
Detection angle:360°
Working temperature:-15°C~+70°C
NOTE:
th
the high-frequency output of this sensor
is <0.2mW- that is just one 5000 of the transmission
oven.
power of a mobile phone or the output of a microwave
Power source: 12V/DC 24V/DC
110-130V/AC 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Transmission power<0.2mW
It can be installed inside of product that is made of glass and plastic because that these materials make little
effect to microwave. Connect the product as shows below: you can change a common light to an automatic
UTILIZED IN CEILING LIGHT
Connect N, L with power;
Connect N, L’ with load.
Electrical load
Security alarming system
The intelligent lighting system
NLN
L’
Power
L
NL’
N
This product can be utilized in more fields than the above examples.
You can also install a SK601A in the ceiling directly to control an aisle. There is no problem.
APPLICATION PLACES
In shell chassis Cover cover into buckle
According to customer's need selected.
I 44
P
C oncise modeling,and the shell
increases the IP CODE.
light.
82mm
76mm
90mm
41.5 m m 39.0 m m
NLN
L’
Rated load:
1000W/5A,Max,tungsten(cosφ=1)(220-240V/AC)
300W/2.5A,Max,fluorescent(cosφ=0.5)(220-240V/AC)
600W/5A,Max,tungsten(cosφ=1)(100-130V/AC)
150W/2.5A,Max,fluorescent(cosφ=0.5)(100-130V/AC)
-3-
Microwave Sensor Microwave Sensor
SK601A instruction SK601A instruction
The light can be set to stay ON for any period of time between approx.10sec(turn fully
anticlockwise) and a maximum of 12min(turn fully clockwise). Any movement detected
before this time elapse will re-start the timer. It is recommended to select the shortest
Note: after the light switches OFF, it takes approx. 4sec before it is able to start detecting
movement again. The light will only switch on in response to movement once this period has
elapsed.
it fullyanti-clockwise to select dusk-to-dawn operation at about 10 lux. Turn it fully
clockwise to select daylight operation at about 2000lux. The knob must be turned fully
clockwise when adjusting the detection zone and performing the walk test in daylight.
10sec~12min
10~2000LUX
please do not adjust the sensitivity to maximum, to avoid the product does not
work normally caused by wrong motion.Because the sensitivity is too high easily
wrong motion by interference of power grid & electrical equipment.All those lead
the product does not work normally ! When the product does not work normally,please
try tolower thesensitivity appropriately, and then test it.
When use this product, please adjust the sensitivity to an appropriate position you need,
detect the wrong motion by wind blowing leaves & curtains, small animals, and the
Time setting
Light-control setting
The chosen light response threshold can be infinitely from approx. . Turn10~2000Lux
In different cases, the sensitivity of the lights has certain deviation.
time for adjusting the detection zone and for performing the walk test.
-4-
TROUBLESHOOTING
Malfunction Cause Remedy
wrong light-control setting selected Adjust setting
load faulty Change load
The load will not work
mains switch OFF Switch ON
The load work always
continuous movement in the detection
zone
Check zone setting
the sensor not mounted for detecting
movement reliably
Securely mount enclosure
identifiable movement
movement occurred, but not identified
by the sensor(movement behind wall,
movement of a small object in immediate
lamp vicinity etc.)
Check zone setting
movement
rapid movements are being suppressed
to minimize
malfunctioning
the
zone you have set is too small
Check zone setting
detection
or
Note: please don’t adjust the three functional buttons to excess. That is because the three functional
buttons were connected to the components directly, there is a small stopper in each of
the three components, when you adjust the buttons from start to end, the excessive turn
will damage the stopper
，
and lead to the 360°non-stop turn around. The adjust range limit
is 270°, please do pay attention to this.
The load work without any
The load will not work despite
3. Being installed in the place where the traffic is busy will lead to misoperation.
4. It will lead to misoperation when there are sparks produced by some equipment nearby.
Warning !
1. Being installed in the rocking object will lead to misoperation.
2. The shaking curtain which is blown by wind will lead to misoperation, please select the suitable installed place.
The following situation will lead to misoperation
-2-
Warning!
This product will be faithfully waiting for you. It will turn on the light automatically when you pass by, and
turn off the light automatically when you leave off. You can set the closing delay time to meet your needs.
For example, you may adjust the TIME knob to select the delay time 12min when you think you will come
back in 10mins. The TIME knob is as follow (Keep away from the detecting zone after adjusting the testing
time or that the detecting time will be inaccurate when any moving object is detected again by the product).
The product can not work normally if there is
metal material behind the Installed place.
LUX
SENS TIME
Microwave Sensor Microwave Sensor
SK601A instruction SK601A instruction
-1-
SK601A
If you want to detect small zone‚you can just adjust the sense knob SENS to the range that you
need (You may need to adjust some times untill you think it is suitable).If you want that the light can
be turned on when the circumstance luminance is under some value, you can just adjust the knob LUX
(The working luminance knob) to select the luminance value (You may need to adjust some times untill you
think it is suitable).
Detection range setting(sensitivity)
Detection range is the term used to describe the radii of the more or less circular
turn the detection control fully anticlockwise to select minimum detection range
(approx.1m radii), and fully clockwise to select maximum detection range (approx.
8m radii).
with middle figure and moves at a speed of 0.6~1.5m/sec. if person’s stature, figure and
moving speed change, the detection distance will also change.
1~8m
detection zone produced on the ground after mounting the sensor light at a height of 2.5m,
Note: the above detection range is gained in the case of a person who is between 1.6m~1.7m tall
Non-metal material
When the sensor is installed inside the ceiling floor,
the sensitivity to light will be invalid.
SENSOR INFORMATION
Height of installation2.5~3.5M
(Height of installation2.5M)
Min:1m
Max:8m
2.5-3.5m
Sensing distance adjustment range
Min:1m
Max:8m
UTILIZING FIELD AND INTRODUCTION
SK601A is a moving object sensor that can detect range of 360°and it’s working frequency is 5.8G.
The advantage of this product is stable working state (stable working temperature: -15°C~+70°C), SK601A
adopts a microwave sensor (high-frequency output <0.2mW), so that it is safe and performs better than
infrared sensor.
Sensing angle adjustment range
360
SPECIFICATIONS
Installation site:Indoors, ceiling mounting
HF system:5.8GHz CW radar, ISM band
Reach: 1-8m(radii.) adjustable
Time setting:10 sec. to 12min.
Light contro:10~2000Lux
Power consumption:approx.0.9W
Transmission power ：<10mW
Detection angle:360°
Working temperature:-15°C~+70°C
NOTE:
th
the high-frequency output of this sensor
is <0.2mW- that is just one 5000 of the transmission
oven.
power of a mobile phone or the output of a microwave
Power source: 12V/DC 24V/DC
110-130V/AC 220-240V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Transmission power<0.2mW
It can be installed inside of product that is made of glass and plastic because that these materials make little
effect to microwave. Connect the product as shows below: you can change a common light to an automatic
UTILIZED IN CEILING LIGHT
Connect N, L with power;
Connect N, L’ with load.
Electrical load
Security alarming system
The intelligent lighting system
NLN
L’
Power
L
NL’
N
This product can be utilized in more fields than the above examples.
You can also install a SK601A in the ceiling directly to control an aisle. There is no problem.
APPLICATION PLACES
In shell chassis Cover cover into buckle
According to customer's need selected.
I 44
P
C oncise modeling,and the shell
increases the IP CODE.
light.
82mm
76mm
90mm
41.5 m m 39.0 m m
NLN
L’
Rated load:
1000W/5A,Max,tungsten(cosφ=1)(220-240V/AC)
300W/2.5A,Max,fluorescent(cosφ=0.5)(220-240V/AC)
600W/5A,Max,tungsten(cosφ=1)(100-130V/AC)
150W/2.5A,Max,fluorescent(cosφ=0.5)(100-130V/AC)
Table of contents
