Sharp AQUOS LC-37GE1E User manual

LC-37GE1E
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISION COULEUR À ÉCRAN
À CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
ENGLISHDEUTSCHFRANÇAIS
SHARP CORPORATION
SHARP ELECTRÓNICA ESPAÑA S.A.
Polígono Industrial Can Sant Joan
Calle Sena s/n
08174 SANT CUGAT DEL VALLÉS
BARCELONA (ESPAÑA)
Printed in Spain
Gedruckt in Spanien
Imprimé en Espagne
Stampato in Spagna
Gedrukt in Spanje
Impreso en España
TINS-C415WJZZ
06P07-SP-NG
LC-37GE1E OPERATION MANUAL / BEDIENUNGSANLEITUNG / MODE D'EMPLOI / MANUALE DI ISTRUZIONI / GEBRUIKSAANWIJZING / MANUAL DE MANEJO
Printed on environmentally friendly paper
Auf ökologischem Papier gedruckt
Imprimé sur papier écologique
Stampato su carta ecologica
Afgedrukt op ecologisch papier
Impreso en papel ecológico
ITALIANONEDERLANDSESPAÑOL
C415WJZZ 1
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D'EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
PIN

676.9/676,9
930.0/930,0 120.0/120,0
110.1/110,1
304.0/304,0
463.8/463,8
822.6/822,6
64.0/64,0 660.0/660,0
577.0/577,0
83.0/83,0
724.0/724,0
436.7/436,7
2°
6°
10°
10°
200.0/200,0 110.0/
110,0
200.0/200,0
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
ASA
and of the same rating as above,
which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains
plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a
safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric
shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

1
ENGLISH
OPERATION MANUAL ENGLISH
Contents.........................................................................................1
Dear SHARP customer..................................................................2
Important Safety Precautions ......................................................2
Trademarks....................................................................................2
Supplied accessories....................................................................3
Quick guide....................................................................................3
Setting the TV ...........................................................................3
TV (Front view) .........................................................................4
TV (Rear view) ..........................................................................4
Inserting the batteries................................................................5
Using the remote control unit ....................................................5
Cautions regarding the remote control unit ..........................5
Remote control unit ..................................................................6
Turning on the power................................................................7
Standby mode ..........................................................................7
Initial auto installation (Analogue) ...............................................7
Initial auto installation (DTV).......................................................7
Channel selection using the station list (Analogue).....................8
Using external equipment.............................................................9
Connecting a VCR ...................................................................9
Connecting a game console or camcorder................................9
Connecting a DVD player..........................................................9
Connecting a decoder ............................................................10
Connecting a PC ....................................................................10
Using AV Link function ............................................................10
Menu operations..........................................................................11
On-Screen Display..................................................................11
Common operations ...............................................................11
Menu operation without a remote control................................11
Picture menu ..........................................................................12
Backlight ......................................................................12
Contrast .......................................................................12
Brightness ....................................................................12
Colour ..........................................................................12
Tint ...............................................................................12
Sharpness ....................................................................12
Red ..............................................................................12
Green ...........................................................................12
Blue..............................................................................12
Colour temp. ................................................................12
Black ............................................................................12
3D-Y/C.........................................................................12
DNR (Digital Noise Reduction).......................................12
I/P setting .....................................................................12
Film mode.....................................................................13
truD(R)..........................................................................13
Quick shoot ..................................................................13
Reset............................................................................13
Sound menu...........................................................................13
Treble ...........................................................................13
Bass.............................................................................13
Loudness......................................................................13
Auto volume .................................................................13
Balance ........................................................................13
Clear voice....................................................................13
Reset............................................................................13
Connections menu..................................................................14
Decoder .......................................................................14
Input select...................................................................14
HDMI setup ..................................................................14
Supply voltage..............................................................15
AV-Link (EXT 2 only) .....................................................15
Miscellaneous...............................................................15
Setup menu............................................................................15
Channels ......................................................................15
Child lock......................................................................16
Auto format ..................................................................16
Language .....................................................................16
Factory settings ............................................................16
Miscellaneous...............................................................17
Contents
Geometry menu......................................................................17
Picture horizontal..........................................................17
Picture vertical ..............................................................17
Phase position..............................................................17
Other menu items ...................................................................18
AV mode ...........................................................................18
Status display ....................................................................18
INPUT SOURCE ................................................................18
Still image ..........................................................................18
OPC ..................................................................................18
Wide modes ......................................................................19
Analogue teletext ....................................................................20
Using analogue teletext menu............................................20
Newsflash.....................................................................20
Reveal/Conceal ............................................................20
Setup............................................................................21
DTV menu operations .................................................................22
DTV menu operation buttons ..................................................22
DTV On-Screen Display ..........................................................22
DTV common operations ........................................................22
About using the character set screen.................................23
Language................................................................................23
Programme Setup ..................................................................23
Favourite.......................................................................24
Lock .............................................................................24
Move ............................................................................24
Move To .......................................................................24
Skip..............................................................................24
Select ...........................................................................25
Erase............................................................................25
Label ............................................................................25
View .............................................................................25
Installation...............................................................................25
Auto Installation .................................................................25
Carrier Scan.......................................................................25
Carrier Setup .....................................................................26
System Setup .........................................................................26
OSD Setup ........................................................................26
Child Lock .........................................................................27
Accessories ............................................................................27
Software Version................................................................27
Software Upgrade..............................................................27
Common Interface ..................................................................28
Inserting a CA card ............................................................28
Supplying power to the antenna..............................................28
About EPG..............................................................................29
Using the EPG ...................................................................29
Using the EPG Timer .........................................................29
Using the ESG ........................................................................30
Using the digital programme list ..............................................30
Viewing a service banner.........................................................30
Using the multi audio function .................................................31
Displaying subtitles .................................................................31
Using the MHEG5 application (UK only) ..................................31
Appendix ......................................................................................32
Removing the stand................................................................32
Removing the speakers ..........................................................33
Troubleshooting......................................................................34
PC compatibility chart.............................................................35
RS-232C port specifications ...................................................35
Specifications .........................................................................37
Optional accessories...............................................................37
End of life disposal..................................................................38
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the
actual operations.
LC-37GE1E_gb_a.indd 1LC-37GE1E_gb_a.indd 1 2006/08/24 15:15:192006/08/24 15:15:19

2
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of trouble-
free operation of your product, please read the Important Safety Precautions carefully before using this product.
Dear SHARP customer
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub,
swimming pool and in a wet basement.
• Do not place vases or any other water-filled containers on this product.
The water may spill onto the product causing fire or electric shock.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause
the product to fall, resulting in serious personal injuries as well as damage to the product. Use only
a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product.
When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only
the mounting hardware recommended by the manufacturer.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops,
excessive force and uneven floor surface can cause the product to fall from the cart.
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or
block these vents and openings since insufficient ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they
can block ventilation openings. This product is not designed for built-in installation; do not place the
product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or impact
applied. If the LCD panel is broken, be careful not to be injured by broken glass.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
• To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• There is power consumption always if main plug is connected.
• Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high
voltage and other dangerous conditions. Request a qualified person to perform servicing.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a
fixed point of blue, green or red.
This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two
people holding it with two hands — one hand on each side of the TV.
Important Safety Precautions
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC.”
• The “HD ready” Logo is a trademark of EICTA.
Trademarks
• truD is a registered trademark of Micronas in Germany and other countries.
LC-37GE1E_gb_a.indd 2LC-37GE1E_gb_a.indd 2 2006/08/24 15:15:222006/08/24 15:15:22

3
Supplied accessories
Remote control unit
(g1)
AC cord (g1)
Pages 5 and 6
Product shape varies in
some countries.
Page 3
• “AAA” size battery (g2)..........Page 5
Cable clamp (g1)
Page 3
Cable tie (g1)
Page 3
3 RCA to 15-pin D-sub
adapter (g1)
Page 9
• Operation manual (This publication)
Quick guide
Setting the TV
Standard DIN45325
plug (IEC 169-2)
75 qcoaxial cable
Antenna
Connect the antenna cable from your antenna-/cable socket or the (room-/roof) antenna for antenna input terminal on the
back of your TV set to receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good reception conditions. Passive and active room antennas are offered
commercially. In an active antenna its power is supplied via the antenna input terminal.
The supply voltage (5V) must be correspondingly set under “Supply voltage”. (Page 15)
* Ferrite Core
The Ferrite Core should be permanently attached and never removed from the AC cord.
Setting the TV on the wall
• This TV should be mounted on the wall only with the wall mount bracket available from SHARP. (See page 37.)
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the LCD Colour TV requires special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting
or mounting that results in accident or injury.
• You can ask a qualified service personnel about using an optional bracket to mount the TV to the wall.
AC cord
Product
shape
varies
in some
countries.
Cable clamp
Cable tie
Place the TV close to the
AC outlet, and keep the
power plug within reach.
Ferrite
Core *
Before making any
connections, press
down on the upper
hooks and remove the
rear terminal covers
towards you.
LC-37GE1E_gb_a.indd 3LC-37GE1E_gb_a.indd 3 2006/08/24 15:15:222006/08/24 15:15:22

4
TV (Front view)
Quick guide
TV (Rear view)
NOTE
• Only if you use an
active terrestrial
antenna, select “yes
(5V)” under “Supply
voltage”. (Page 15)
AC INPUT terminal
OPC sensor
Remote control sensor
B (Standby/On) indicator
OPC indicator
a(Power button)
MENU button
i(l/k)
(Volume buttons)
P(s/r)
(Programme [channel] buttons)
SLEEP indicator
EXT 2 (AV) terminal
EXT 3 terminals
Headphone jack
EXT 1 (RGB) terminal
EXT 5 (HDMI/AUDIO)
terminals
Antenna input terminal
(DVB-T 5V=/80 mA)
OUTPUT (Audio)
terminals
EXT 4 terminals
RS-232C terminal
COMMON INTERFACE
slot
EXT 6 (HDMI) terminal
LC-37GE1E_gb_a.indd 4LC-37GE1E_gb_a.indd 4 2006/08/24 15:15:262006/08/24 15:15:26

5
Quick guide
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
chemical leakage in old batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find
any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
30° 30°
Remote control sensor
5 m
Press and slide the battery cover to open it.
Insert two supplied “AAA” size batteries.
• Place batteries with their terminals corresponding
to the (e) and (f) indications in the battery
compartment.
Close the battery cover.
1
2
3
Inserting the batteries
Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control
unit and sensor may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The
heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor
of the TV is under direct sunlight or strong lighting. In such case, change
the angle of the lighting or TV, or operate the remote control unit closer to
the remote control sensor.
LC-37GE1E_gb_a.indd 5LC-37GE1E_gb_a.indd 5 2006/08/24 15:15:272006/08/24 15:15:27

6
Remote control unit
Quick guide
12
3
4
7
9
10
15
16
12
8
5
6
11
14
17
13
18
19
21
27
29
30
22
23
25
24
28
26
20
1 B(Standby/On)
(Page 7)
2 m(Teletext)
TV: Display the analogue teletext.
(Page 20)
DTV: Select DTV data broadcasting
and TELETEXT. (Page 31)
3 k(Reveal hidden Teletext)
(Pages 20 and 21)
4 [(Subtitle for Teletext)
TV/External: Subtitle on/off. (Page 21)
DTV: Display the subtitle selection
screen. (Page 31)
5 3(Freeze/Hold)
(Page 21)
6 1(Subpage)
(Page 21)
7 –
Set the channel in TV and DTV mode.
Enter the desired numbers or letters.
Set the page in Teletext mode.
8 A(Flashback)
Press to return to the previous image
in normal viewing mode.
9 DTV
Press to access DTV mode while
watching other input sources, and
vice versa.
(Will not work if you were watching
DTV immediately before turning off
the TV. In this case first select any
other input source except DTV using
the bbutton.)
10 2(Sound mode)
Select the sound multiplex mode.
(See below.)
11 e(Mute)
Sound on/off
12 i(k/l) (Volume)
Increase/decrease volume.
13 LIST
DTV: Display the programme list.
14 DTV MENU
DTV: Display DTV Menu screen.
17 SLEEP
Set the sleep timer on (in units of 30
min. up to max. 2hr. 30min) and off.
(If the “Time and date” screen is
displayed, enter the time and date as
explained on page 17, and set the
sleep timer again.)
18 v(Top/Bottom/Full)
Set the area of magnification in
analogue teletext mode. (Page 21)
19 b(INPUT SOURCE)
Select an input source.
(TV, DTV, EXT1, EXT2, EXT3, EXT4,
EXT5, EXT6) (Page 18)
20 EPG
DTV: To display EPG (Electronic
Programme Guide) screen.
ESG
DTV: To display ESG (Electronic
Service Guide) screen.
RADIO
DTV: Switch between RADIO and
DTV mode.
21 AV MODE
Select a video setting. (Page 18)
22 SURROUND
Surround effects on/off.
23 P (r/s)
Select the channel.
In analogue TV mode, external input
sources (EXT 1 - 6) can also be
selected.
24 p(Display information)
(Pages 17, 18, 29 and 30)
25 MENU
MENU screen on/off. (Page 11)
26 a/b/c/d(Cursor)
Select a desired item on the setting
screen.
OK
Execute a command within the menu
screen.
Display the station list in analogue
mode and the programme list in DTV
mode.
27 RETURN
Return to the previous menu screen.
28 Colour (Red/Green/Yellow/Blue)
TELETEXT: Select a page. (Page 21)
The coloured buttons are used to
select correspondingly to the coloured
items in the menu screen.
29 OPC
To switch the Optical Picture Control
on and off. (Page 18)
30 f(Wide modes)
Select the wide mode. (Page 19)
Selectable items
Stereo, Mono!
Dual-channel Sound 1, Dual-
channel Sound 2, Dual-
channel Sound 1+2, Mono!
NICAM, Mono!
Signal
Stereo
Bilingual
Monaural
NOTE
• When no signal is input, the sound mode will display “Mono”.
• “Mono!” indicates that you have manually changed to FM mono.
Selectable items
Stereo, Mono!
Dual-channel Sound 1,
Dual-channel Sound 2,
Dual-channel Sound 1+2
Mono
Signal
Stereo
Bilingual
Monaural
NICAM TV broadcasts selection A2 TV broadcasts selection
EUsing 2 on the remote control unit
DTV mode:
Press 2to open the multi audio screen. (Page 31)
Analogue TV mode:
Each time you press 2, the mode switches as illustrated in the following
tables.
15 END
Exit the menu screen.
16 truD
Demonstrate the truD effects in a dual
screen format. (Page 13)
LC-37GE1E_gb_a.indd 6LC-37GE1E_gb_a.indd 6 2006/09/29 11:00:062006/09/29 11:00:06

7
Quick guide
Turning on the power
Press a on the TV.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when ais
turned off.
• In DTV input mode, if the power is turned off immediately
after a setting change from the menu screen, the new
setting or channel information may not be memorised.
Initial auto installation (Analogue)
When the TV powers on for the first time after
purchase, the initial auto installation (Analogue) is
invoked. Follow the menus and make the necessary
settings one after another.
NOTE
• To reconfigure the initial auto installation settings, go to
“Channels” and run “Search wizard” from the Setup menu.
(Page 15)
Setting the on-screen display language
1Press a/b/c/dto select the desired language
listed on the screen.
2Press OK to enter the setting.
Setting the country (“Location of TV set” screen)
1Press a/b/c/dto select your country or area
listed on the screen.
2Press OK to enter the setting.
•
An overview of settings to be used for auto search displays.
Press OK to start the search.
• The TV searches for, sorts and stores all the
receivable TV stations according to their settings and
the connected antenna.
• To abort the initial auto installation in progress, press
END.
When the auto sorting is completed, the item
“Decoder” displays. Press c/dto select “EXT
1” or “EXT 2”, and then press OK.
• Make sure to select the terminal (EXT 1 or 2) to which
the decoder is connected.
A message appears indicating that the first
installation is successfully completed. Press
OK, if necessary.
• If a recording device with AV-Link is connected to
EXT 2, the TV automatically starts transferring the
station list data to the recording device.
1
2
3
4
5
Standby mode
Press Bon the remote control unit when the TV is on.
• The TV enters standby mode and the image on the screen
disappears.
• The
Bindicator on the TV changes from green to red.
• To completely turn off the power to the TV, unplug the AC
cord from the AC outlet. However, do not unplug the AC
cord unless otherwise instructed.
Off
Display status indicator
Power off
Initial auto installation (DTV)
Digital Video Broadcasting is a transmission scheme.
It is much more than a simple replacement for existing
analogue television transmission. DVB provides more
stations, clearer picture quality and other services
displayed on the screen. It also allows a range of new
features and services including subtitles and multiple
audio tracks.
To watch DTV broadcasts, follow the procedures below
to scan all available services in your area.
NOTE
• Make sure to perform Initial auto installation
(Analogue) outlined in the preceding section as well,
even if you intend to view only DTV broadcasts.
Press DTV (or b, then a/bto select “DTV”,
and then press OK) to access the DTV mode.
Press DTV MENU and the DTV Menu screen
displays.
Press c/dto select “Installation”.
Press a/bto select “Auto Installation”, and
then press OK.
If you have already set the PIN, enter it here. If
not, enter the factory preset PIN “1234”.
• See page 16 for setting PIN.
• A confirmation message displays. Press c/dto
select “Yes”, and then press OK to start the search.
The TV starts scanning all available DTV and
radio services in your area.
NOTE
• The language and country settings used in this operation
are the settings you have already set while executing
the Initial auto installation (Analogue). If you want to
reconfigure the country setting, for instance after moving
to another country, conduct “Search wizard” from the
Analogue Menu again. (Page 15)
• The DTV services are searched and stored according to the
channel number information embedded in the TV signal (if
available). If the information is not available, the services are
stored according to the order in which they were received.
If you would like to sort the order, it is possible to arrange it
as explained in page 24.
• To cancel the scan in progress, press END.
• You cannot select any DTV-related menu items unless “Auto
Installation” has been completed.
1
2
3
4
5
Green
Red The TV is in standby mode.
The TV is on.
LC-37GE1E_gb_a.indd 7LC-37GE1E_gb_a.indd 7 2006/08/24 15:15:312006/08/24 15:15:31

8
Press a/b/c/dor - to select the
desired station in the station list, and then press
OK to tune in the station.
• Press Blue to sort the list according to “Alphabetical”
or “Numerical”.
• Refer to the following table for how each numeric
button is assigned a set of characters.
To delete, move, and rename stations from
the station list
While in the station list, press Yellow (Change
stations).
EDelete
Select a station to delete, and then press Red
(Delete). Mark more stations with a/b/c/dor
- , if desired. Confirm with OK or cancel
with Red.
EMove
Select a station to move, and then press Yellow
(Move). Mark more stations with a/b/c/dor
- , if desired. Press OK to finish marking.
Press a/b/c/dor - to select the
position to move to. Confirm with OK or cancel
with Yellow.
• Make sure to select the appropriate block of channels
or destination when moving.
ERename
Select a station to rename, and then press Blue
(Rename). Press any of the numeric buttons
- to select the desired character. Remember
to press and toggle the numeric button quickly,
for the transition to the next digit is rather quick.
Repeat until the new name is fully spelt out.
Confirm with OK or cancel with Blue.
• The name can be up to 8 characters.
2
Quick guide
Channel selection using the station
list (Analogue)
This section explains how to change/delete/
move/rename stations using the analogue
Station List. If you are watching DTV, refer
to the “Using the digital programme list”
section. (Page 30)
You can also select the desired channel from station
list instead of using - numeric buttons or P(r/
s).
In analogue TV mode, press OK when no other
menu screen is active.
1
Station list Numerical
0
1
2
3
4
DTV
EXT1
EXT2
EXT3
EXT4
EXT5
EXT6
VIDEO
ARD
ZDF
SAT.1
RTL
5
6
7
8
9
10
11
12
13
14
15
16
VOX
S-RTL
N-TV
DSF
9LIVE
PRO7
RTL2
WDR 3
BR
HR
MDR 3
KIKA
Entering characters using the - buttons
Assigned characters and numbers
Buttons
W, X, Y, Z, 9
0
1, k, l, . (dot), (space)
A, B, C, 2
D, E, F, 3
G, H, I, 4
J, K, L, 5
M, N, O, 6
P, Q, R, S, 7
T, U, V, 8
LC-37GE1E_gb_a.indd 8LC-37GE1E_gb_a.indd 8 2006/08/24 15:15:312006/08/24 15:15:31

9
VIDEOS-VIDEOL-AUDIO-R
AV OUTPUT
Using external equipment
Setting the input source
To view external source images,
select the input source using bon
the remote control unit. (Page 18)
NOTE
• The cables marked with * are
commercially available items.
• TV-OUT from EXT 1 outputs DTV
image when DTV is selected as the input.
Otherwise it constantly outputs analogue TV image.
• MONITOR OUTPUT from EXT 2 outputs audio only when
EXT 4, 5 and 6 is selected as the input.
Connecting a VCR
You can use the EXT 2 terminal when connecting a
VCR and other recording equipment.
If your VCR supports TV-VCR advanced AV Link
systems, you can connect the VCR using the fully-
wired SCART cable.
NOTE
• If the above is your connection, make sure to select
“EXT 2” under the menu item “Decoder” when you
run the Initial auto installation (Analogue) (Page 7) or
when changing the setting later (Page 14).
• TV-VCR advanced AV Link systems may not be compatible
with some external sources.
VCR Decoder
SCART cable* SCART cable*
EXT 2 (recommended)
VIDEOS-VIDEOL-AUDIO-R
AV OUTPUT
Connecting a DVD player
You can use the EXT 3, 4, 5 (HDMI) or 6 (HDMI)
terminals when connecting to a DVD player and other
audiovisual equipment.
DVD player
EXT 3
A game console, camcorder and some other
audiovisual equipment are conveniently connected
using the EXT 3 terminals.
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
Connecting a game console or
camcorder
Game console Camcorder
or
S-video cable*
Composite
video cable*
AUDIO cable*
EXT 3
or
AUDIO cable*
S-video cable*
Composite
video cable*
YPB
(CB)
PR
(CR)
COMPONENT
EXT 4
ø 3.5 mm stereo minijack cable*
Component
cable*
3 RCA to 15-pin
D-sub adapter
(Supplied)
DVD player
NOTE
• EXT 3: The S-VIDEO terminal has priority over the VIDEO
terminals.
NOTE
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
DVD player
HDMI-DVI conversion
adapter/cable*
When using an HDMI-DVI
conversion adapter/cable,
input the Audio signal here.
If not, use EXT 6.
EXT 5
DVD player
HDMI cable*
EXT 6
INPUT SOURCE
TV
DTV
EXT1
EXT2
EXT3
EXT4
EXT5
EXT6
LC-37GE1E_gb_a.indd 9LC-37GE1E_gb_a.indd 9 2006/08/24 15:15:352006/08/24 15:15:35

10
Using external equipment
NOTE
• The cables marked with * are commercially available items.
• The PC input terminals are DDC1/2B-compatible.
• Refer to page 35 for a list of PC signals compatible with the
TV.
• Macintosh adaptor may be required for use for some
Macintosh computers.
• When connecting to a PC, the correct input signal type is
automatically detected.
This TV incorporates four typical AV Link functions
for smooth connections between the TV and other
audiovisual equipment.
One Touch Play
While the TV is in standby mode, it automatically turns
on and plays back the image from the audiovisual
source (e.g. VCR, DVD).
TV Standby
When the TV enters standby mode, the connected
audiovisual equipment (e.g. VCR, DVD) enters standby
mode as well.
WYSIWYR (What You See Is What You
Record)
When the remote control unit of the connected VCR
has the WYSIWYR button, you can automatically start
recording by pressing the WYSIWYR button.
Preset Download
Automatically transfers the channel preset information
from the tuner on the TV to the one on the connected
audiovisual equipment (e.g. VCR) via the EXT 2
terminal.
NOTE
• Refer to operation manuals of each external equipment for
the details.
• Only works when the audiovisual equipment is connected
to the EXT 2 terminal on the TV with AV Link via a fully
wired SCART.
• The use of the AV Link function is only possible if the TV-
set has enforced a complete auto-installation with the
connected audiovisual equipment (Page 7, initial auto
installation).
The availability of the AV Link function depends on
the audiovisual equipment used. Depending on the
manufacturer and type of equipment used, it is possible
that the described functions may be completely or partially
unusable.
Using AV Link function
Connecting a PC
Use the EXT 4 terminals to connect a PC.
PC
ø 3.5 mm stereo minijack cable*
RGB cable*
PC
RGB/DVI conversion cable*
ø 3.5 mm stereo minijack cable*
EXT 4
EXT 4
Connecting a decoder
You can use the EXT 1 terminal when connecting a
decoder and other audiovisual equipment.
NOTE
• If the above is your connection, make sure to select
“EXT 1” under the menu item “Decoder” when you run
the Initial auto installation (Analogue) (Page 7) or when
changing the setting later (Page 14).
Decoder
EXT 1
SCART cable*
LC-37GE1E_gb_a.indd 10LC-37GE1E_gb_a.indd 10 2006/08/24 15:15:382006/08/24 15:15:38

11
Menu operations
On-Screen Display
Example
Item highlighted in yellow
• This indicates the item currently selected.
Item displayed in white
• This indicates an item can be selected.
NOTE
• Some menu items do not appear as explained in this
manual depending on the selected parameter, input mode
or the type of signal received.
• The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
Common operations
Press MENU and the TV menu screen displays.
Press c/dto select the desired menu, and
then press OK.
Press a/bto select the desired menu item.
Press OK to proceed if necessary.
1
2
3
Menu operation without a remote control
This function is useful when there is no remote control
within your reach.
Adjusting frequently adjusted items
Press MENU briefly to display the direct control
screen.
• You can adjust the following items: “INPUT
SOURCE”, “Brightness”, “Contrast”, “Wide modes”
and “Service”.
• “Service” is the item reserved only for service
personnel.
Select the item by pressing Pr/s.
Select or adjust by pressing ik/l.
NOTE
• The direct control menu screen will disappear if left
unattended for several seconds.
1
2
3
Picture
TV menu
Sound
SOFT
Backlight
Contrast
Brightness
Colour
Tint
Sharpness
more ...
0
3
-12
9
0
3
Connections
High
off
off
off
Interlace
off
off
no
Mid-High MiddleColour temp.
Black
3D-Y/C
DNR
I/P setting
Film mode
offtruD(R)
Quick shoot
Reset
• Press
a/bto select “more ...” and then press OK, if
the item you want to adjust is not displayed.
Press c/dto select the desired item or move
the item to the desired position. Press OK if
necessary.
Press RETURN repeatedly to return to the
last menus, or press END or MENU to exit the
menu.
4
5
Picture
TV menu
Sound
SOFT
Backlight
Contrast
Brightness
Colour
Tint
Sharpness
High
off
off
off
Interlace
off
off
no
Mid-High Middle
0
3
-12
9
0
3
Colour temp.
Black
3D-Y/C
DNR
I/P setting
Film mode
offtruD(R)
Quick shoot
Reset
Connections
Current AV
mode is
shown here.
(Page 18)
LC-37GE1E_gb_b.indd 11LC-37GE1E_gb_b.indd 11 2006/08/24 15:16:102006/08/24 15:16:10

12
Picture menu
Various picture-related settings can be optimised.
TitleB
Menu operations
NOTE
• Items with * can be adjusted and reset for each individual
AV mode.
• Items with ** appear only when “PC (RGB)” for EXT 4 is
selected under “Input select”.
• Press a/bto select “more ...” and then press OK, if the
item you want to adjust is not displayed.
Backlight*
Dims or brightens the screen.
Contrast*
The contrast settings depend on the brightness of the
room. The brighter the surroundings the higher the
contrast should be set.
Brightness*
Set the brightness so that the black areas of the picture
only appear black.
Colour*
Set the colour intensity according to your personal
taste. The colours should appear natural which is best
recognizable from the colour of peoples’ faces, for
example.
Tint
Set the tint so that the colours appear natural. This can be
judged from the colour of peoples’ faces, for example.
Sharpness*
Adjust the sharpness to obtain the desired image
definition.
Red**
Adjust red colour intensity.
Green**
Adjust green colour intensity.
Blue**
Adjust blue colour intensity.
High: White with bluish tone
Mid-High: Intermediate tone between High and Middle
Middle: Natural tone
Mid-Low: Intermediate tone between Middle and Low
Low: White with reddish tone
Item
off: No detecting
Standard: Normal adjustment
Fast: Set the optimum image quality for fast-moving
images.
Slow: Set the optimum image quality for slow-moving
images.
Item
Picture
TV menu
Sound
SOFT
Backlight
Contrast
Brightness
Colour
Tint
Sharpness
more ...
0
3
-12
9
0
3
Connections
Colour temp.*
Adjust the colour temperature to give the best white
image.
Interlace: Display finely detailed images for TV or video,
etc.
Progressive: Display smooth images for still images or
graphics, etc.
Item
PC only
PC only
PC only
Black
For easier viewing, change the viewing depth by
selecting a level for automatically adjusting the dark
portion of an image.
3D-Y/C
Provide high quality images with minimal dot crawl and
cross colour noise by detecting changes in the image.
NOTE
• 3D-Y/C may not operate depending on the input signal
type or noisy input signal.
• 3D-Y/C has even more effect on composite video signals
(CVBS).
DNR (Digital Noise Reduction)
Produce a clearer image. (off, High, Low)
I/P setting
Adjust the image and input signal can give you a more
beautiful picture.
NOTE
• The I/P setting is set to “Progressive” when Film mode is
“on”.
LC-37GE1E_gb_b.indd 12LC-37GE1E_gb_b.indd 12 2006/09/29 11:00:372006/09/29 11:00:37

13
Menu operations
Sound menu
Various sound-related settings can be optimised.
NOTE
• Items with * can be adjusted and reset for each individual
AV mode.
• Press
a/bto select “more ...” and then press OK, if the
item you want to adjust is not displayed.
Treble*
For weaker or stronger treble
Bass*
For weaker or stronger bass
Loudness
Boosts low and high frequencies to give added punch
to playback even at a low volume level.
Auto volume
The volume may vary when receiving stations with
different standards or when switching from station to
station or during commercial breaks. You can reduce
these differences in volume by activating Auto volume.
Switch off the automatic function for the reception of
music programmes and live broadcasts for a better
sound.
Balance
Set the balance to achieve equal volume from the right
and left sides.
Clear voice
This function emphasises speech voice against the
background noise for more intelligibility. It is not
recommended for music sources.
Reset
Select if you wish to reset all sound-related items to the
factory presets.
TV menu
Sound
SOFT
Treble
Bass
more ...
0
4
Connections
Film mode
Automatically detects a film-based source (originally
encoded at 24/25 frames/second, depending on the
vertical frequency), analyses it and then recreates each
frame for film-like picture quality.
truD(R)
“truD(R)” ensures you steady motion instead of edgy
movements and juddering. It further improves the
image quality by enhancing contrast and sharpness
with advanced video algorithms. When entering the
“truD(R)” menu, you can only switch the juddering
correction on/off. The picture quality adjustments such
as enhanced contrast and sharpness is always on.
NOTE
• Press truD on the remote control unit to show truD
demonstration in a dual screen format.
• This effect is greater on fast moving images such as film
contents.
• If “truD(R)” is activated the items “I/P setting” and “Film
mode” will not be displayed in the menu screen.
• “truD(R)” will not be displayed in the menu screen
depending on the type of signal received (HD signal, etc.).
Quick shoot
Improve LCD response when viewing fast-moving
images. The effect is greater at low room temperatures
(at or below 15˚C).
NOTE
• Quick shoot may cause image noise. If this occurs, set the
function to “off”.
Reset
Select if you wish to reset all picture-related items to
the factory presets.
LC-37GE1E_gb_b.indd 13LC-37GE1E_gb_b.indd 13 2006/08/24 15:16:142006/08/24 15:16:14

14
Menu operations
Connections menu
TV menu
HDMI setup
Supply voltage
AV-Link
Miscellaneous
SetupConnections
Input select
Decoder
no (0V)
EXT 2
Decoder
Make sure to select the terminal (EXT 1 or 2) to which
the decoder is connected.
NOTE
• This setting will be reflected in the “Decoder stations”
function under “Miscellaneous”. (Page 15)
Input select
For setting the signal type of external equipment
NOTE
• If no (colour) image displays, try to change the other
signal type.
• Check the operation manual of the external equipment for
the signal type.
• TV, DTV, EXT3, EXT5 and EXT6 are not displayed in Input
Select.
• If both CVBS and RGB signals are input to EXT 1 using a
SCART cable, the TV may output an RGB signal even though
you have designated CVBS for the respective terminal. This
happens due to the setting of your external equipment.
HDMI setup
HDMI (High-Definition Multimedia Interface) terminal
selection.
Press MENU and the TV menu screen displays.
Press c/dto select “Connections”, and then
press OK.
Press a/bto select “HDMI setup”, and then
press OK.
Press a/b to select “EXT5” or “EXT6”, and
then press OK.
Press a/bto select the desired item.
Press c/dto select the desired setting.
1
2
3
4
5
6
NOTE
• Refer to your external equipment operation manual for the
signal type.
• Items with * may be greyed out depending on the type of
signal input from the external equipment.
• Item marked ** is only available when EXT5 is selected.
Input source
EXT 1
EXT 2
EXT 4
Signal type
Y/C, CVBS, RGB
Y/C, CVBS
PC (RGB), COMPONENT
Selectable
items Description
RGB/YCbCr
4:4:4/YCbCr 4:2:2
ITU601/ITU709
Normal/
Enhanced
Enable/Disable
Digital/Analogue
Signal type*
Colour
matrix*
Dynamic
range*
Auto view
Audio
select**
Select the video signal type
from the HDMI terminal.
Select the internal colour
space conversion method
when an RGB signal is
input.
Select the signal amplitude
range. Usually, select
“Normal”.
Set whether or not to use
Wide mode based on
signal recognition, including
an HDMI signal.
Select “Digital” for audio
signal via the HDMI
terminal. Select “Analogue”
for audio signal via the
AUDIO jack.
HDMI setup
items
LC-37GE1E_gb_b.indd 14LC-37GE1E_gb_b.indd 14 2006/08/24 15:16:152006/08/24 15:16:15

15
Supply voltage
Antennas with an integrated amplifier need a supply
voltage on the antenna line. (Page 3)
AV-Link (EXT 2 only)
With this function you can transfer the station data of
the TV (such as station preset number/name/channel/
frequency) to the recorder if the recorder is set up for
AV-Link. This function is available only for conventional
analogue stations.
Press MENU and the menu screen displays.
Press c/dto select “Connections”, and then
press OK.
Press a/bto select “AV-Link”, and then press OK.
Select “Start transmission”, and then press OK.
• The TV transfers the station list to the AV-Link
recorders connected to EXT 2.
Miscellaneous
E Decoder stations
Encrypted stations should be labelled as decoder
stations, so that they can be decoded automatically by
the connected decoder.
1
2
3
4
Menu operations
EManual adjustment of AV standard
Ask your dealer which standard to select for specific
AV equipment (if it is not recognised automatically).
Select the appropriate external terminal (EXT 1- 3) and
its AV standard as advised.
E Allow switching voltage
If this function is activated and you switch to an AV
device (connected to EXT 1 or 2) that delivers switching
voltage to playback, its picture and sound will be
reproduced immediately at all TV presets. (This function
is available only for analogue TV and DTV mode.)
Setup menu
You can search for stations automatically or manually
as well as set the menu language, time and date, child
lock, on-screen displays, etc.
Channels
The menu contains the automatic station search and
the manual station settings. You can re-sort stations,
enter and change station names, and delete stations.
E Search wizard
Use this menu to search for stations automatically once
certain settings have been made. (See page 7, Initial
auto installation (Analogue) for details.)
Press MENU and the TV menu screen displays.
Press c/dto select “Setup”, and then press
OK.
Press
a/bto select “Channels”, and then
press OK.
Press
a/bto select “Search wizard”, and then
press OK.
• You will get a table for the auto station search.
If necessary select “Change search settings”,
and then press OK. Otherwise skip to step 8.
Press a/b/c/dto select your country or area
listed on the screen, and then press OK.
Indicate whether you wish to have “all” stations
or “new ones only” searched for using c/d,
and then press OK.
Select the desired TV/colour standard, and then
press OK.
Specify from which station position onwards the
stations are to be stored, and then press OK.
Press a/bto select “Start search”, and then
press OK.
NOTE
• The station search may take some time.
• Do not make any entries or switch off the set during this
time.
• When the search has ended you will be shown the found
and stored stations sorted in numerical order.
• After the station search has been completed, close the
table by pressing END.
1
2
3
4
5
6
7
8
TV menu
Child lock
Auto format
Language
Factory settings
Miscellaneous
on
Geometry
Channels
Setup
Items
Select decoder
station(s)
Sound encoding
Description
Press OK to mark an encoded station. The
marking can be removed from a station that
has already been marked by pressing the same
key.
For reception of encoded audio signals select
either “always” if these are always encoded or
“Automatic” if these are sometimes encoded.
For audio signals which are always uncoded,
select “never”.
LC-37GE1E_gb_b.indd 15LC-37GE1E_gb_b.indd 15 2006/08/24 15:16:162006/08/24 15:16:16

16
Menu operations
EManual tune
Use the manual tune option when receiving TV signal
whose TV/Colour standard deviate from the one
specified already. However, this requires detailed
knowledge.
Press MENU and the TV menu screen displays.
Press c/dto select “Setup”, and then press
OK.
Press a/bto select “Channels”, and then
press OK.
Press a/bto select “Manual tune”, and then
press OK.
Now enter the necessary setting parameters for
each menu item.
• For “Channel” and “Frequency”, you can initiate the
search by pressing Blue (Search) or simply enter the
number if you know it.
• For items “TV stand.” and “Col. standard”, you must
first press OK (Adopt) to confirm the change.
When you have finished the adjustments, press
Red (Store) to store the new settings.
Next, select the channel position to store the
new settings. Press Red to overwrite the current
station or Blue to insert the new channel.
1
2
3
4
5
6
7
Channel: You can enter the channel number directly here.
Press c/dto move between the receiving channel
modes.
Frequency: You enter the frequency directly using the
numeric buttons. For fine tuning, use the c/dbuttons.
Fine tuning may be necessary for analogue channels or
for recorder playback via the antenna connection.
Name: You can enter an 8-character channel name. Refer
to page 8 for the character input method.
TV stand.: Ask your dealer which standard to select for
specific channels or AV equipment. (B/G, I, L, D/K)
Col. standard: Ask your dealer which standard to select
for specific channels or AV equipment. Selectable colour
standard varies depending on the selected TV standard.
(Auto, PAL, SECAM)
Item
EChange stations
You can move stations, enter or change station names,
and delete stations. The operation is the same as
explained in page 8, “To delete, move, and rename
stations from the station list”.
Child lock
With the child lock you can bar access to all stations
immediately or daily for a certain time period.
To use this function, you have first to define your PIN.
NOTE
• To view a locked channel, you must enter the PIN. (See
page 27 for locking channels from viewing in DTV mode.)
• The TV power will be turned off if no PIN is entered for
several seconds.
ELock immediately
You can lock out all stations immediately by selecting
“yes”. The lock is effective immediately and effective
whenever you turn on the TV.
ELock daily
Here, enter the daily time period, for which your TV set
is to be locked.
EChange PIN
This allows you to change your PIN.
NOTE
• When in analogue TV mode, the current PIN becomes
invalid if you choose “no” for both “Lock immediately” and
“Lock daily”.
• As a precautionary measure, make a note of your PIN
on the back of this operation manual, cut it out and
keep it in a safe place that children cannot reach.
• See page 34 if you lose or forget your PIN.
Auto format
When Auto format is switched on, the TV recognises
the wide picture mode for Cinemascope or widescreen
films and adjusts itself accordingly.
NOTE
• Use Wide modes if an image does not switch to the desired
screen format.
• When 4:3 picture format (i.e., “Normal”) is manually
selected using the Wide modes function, the Auto format
function is temporarily disabled. Select another input
source or reset the TV power to restore the Auto format
function, and the 4:3 picture format will be automatically
selected depending on the transmitted signal.
Language
You can select a language from the Setup menu. Select
from among 13 languages. (Dutch, English, Finnish,
French, German, Greek, Italian, Polish, Portuguese,
Russian, Spanish, Swedish, Turkish)
Factory settings
Call up the predefined sound and picture factory
settings. Unlike the “Reset” options provided in the
Picture and Sound menus, this will reset all parameters
to the default value all across the various input modes
and AV mode options.

17
Menu operations
TV menu ->Setup
Time and date
Miscellaneous Channels Child lock
On-screen displays
No signal off Enable Disable
E Time and date
When you receive teletext, the correct date and time
setting is picked up automatically by the set.
If you do not receive teletext, you should set the “Date”
and “Time” manually. Also you have additional items
you can adjust as outlined below.
NOTE
• Time and date information configured manually cannot be
overridden automatically by the set.
• If the power to the set is cut off (disconnection of AC
cord, power outage, etc.), the auto time acquisition mode
through teletext reactivates.
Miscellaneous
ENo signal off
When set to “Enable” the TV will automatically enter the
standby mode if there is no signal input for 6 minutes.
NOTE
• When a TV programme finishes, this function may not
operate.
• This function is not available in DTV mode.
EOn-screen displays
Here you can determine which on-screen displays are
to be shown by pressing pon the remote control.
Geometry menu
You can set the geometry values of the picture such as
picture position and phase relation. The adjustments
are stored independently for each input mode.
Picture
TV menu
Picture horizontal
Picture vertical
Phase position
0
0
0
Geometry
Picture horizontal
Sets the horizontal picture position by moving the
picture left and right.
Picture vertical
Sets the vertical picture position by moving the picture
up and down.
Phase position
Adjusting the phase relation ensures a picture without
flicker and noise. (Available only for RGB signal)
PC only
Items
On-screen display
time
Sound mode
Time
Description
Sets the duration of the TV status and station
name display.
• This setting also affects other TV screens.
(Volume, Surround, etc.)
Sound mode display on/off (“yes”/“no”)
Time information display on/off (“yes”/“no”)
Items
Time
Date
Beginning of
daylight-saving
time
End of daylight-
saving time
Description
If you receive a station with teletext after
switching on your TV set, the time and date are
automatically registered. In the case of some
stations, the date may have to be entered
manually. For stations without teletext, enter the
time (00:00 to 23:59) and the date (day.month.
year) using the numeric buttons on the remote
control.
See the above item “Time”.
Enter the date for the beginning of daylight-
saving time if it deviates from the date
calculated automatically.
Enter the date of the end of daylight-saving
time if it deviates from the date calculated
automatically.
LC-37GE1E_gb_b.indd 17LC-37GE1E_gb_b.indd 17 2006/08/24 15:16:172006/08/24 15:16:17

18
Menu operations
Other menu items
Some of the useful features can be directly called up by
pressing assigned buttons on the remote control.
NOTE
• You can adjust the factory presets given in “STANDARD”,
“SOFT”, “ECO” and “DYNAMIC”.
• You can assign different AV mode to each external input
source.
STANDARD: For a highly defined image in a normally
bright room
SOFT: Creates a softer image.
ECO: Reduces power consumption.
DYNAMIC: For a clear-cut image emphasising high
contrast for sports viewing.
USER: Allows the user to customise settings as desired.
You can set the mode for each input source.
AV mode
AV mode gives you five viewing options to choose from
to best match the system environment, which can vary
due to factors like room brightness, type of programme
watched or the type of image input from external
equipment.
Press AV MODE.
• The AV mode menu
displays.
Press AV MODE or a/b
while the AV mode menu
displays on the screen.
• As you toggle down
the options, each is
immediately reflected on the screen. No need to
press OK.
1
2
AV mode
SOFT
ECO
DYNAMIC
USER
STANDARD
INPUT SOURCE
Use the INPUT SOURCE screen to select/check the
external equipment connected to the terminal(s) on the
back of the TV.
To watch images from
external AV equipment,
press b. (Page 9)
• To close the INPUT SOURCE
screen, press b again.
Press a/b to select the
corresponding terminal, and
then press OK.
1
2
Status display
Press
p,a status display appears for a few
seconds.
2 ZDF Mono
13:51
• In the top line you can see the name of the
programme. See page 17 for how to customise the
settings for the status display.
INPUT SOURCE
TV
DTV
EXT1
EXT2
EXT3
EXT4
EXT5
EXT6
Item
Still image
You can freeze a motion picture on the screen.
Press 3.
Press 3again to exit still image.
NOTE
• This function may not be available depending on signal
condition.
1
2
OPC
Automatically adjusts the brightness of the screen.
Press OPC on the remote control unit to switch
the Optical Picture Control on and off.
NOTE
• When set to “on”, the TV senses the surrounding light and
automatically adjusts the backlight brightness. Make sure
no object obstructs the OPC sensor, which could affect its
ability to sense surrounding light.
• Under the factory default condition, OPC becomes active
when you select “ECO” for the AV mode.
• OPC turns off whenever an adjustment is made to the
“Backlight” setting.
• OPC can be adjusted and reset for each individual AV
mode.
LC-37GE1E_gb_b.indd 18LC-37GE1E_gb_b.indd 18 2006/08/24 15:16:182006/08/24 15:16:18