Sharp Notevision PG-D45X3D User guide

MODEL
PG-D50X3D
PG-D45X3D
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments .............................. 2
RS-232C Specifications and Commands ........... 4
Setting up the Projector Network Environment ... 9
1. Connecting the Projector to a Computer ...........10
2. Setting an IP Address for the Computer ............11
3. Setting up a Network Connection for the
Projector.......................................................13
Controlling the Projector via LAN ..................... 15
Controlling the Projector Using Internet Explorer
(Version 5.0 or later)......................................15
Confirming the Projector Status (Status)................16
Controlling the Projector (Control)..........................16
Setting and Adjusting the Projector
(Settings & Adjustments) ..............................17
Setting the Security (Network – Security)...............17
Making General Settings for the Network
(Network – General).....................................18
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ..........................18
Setting Error Items and Destination Addresses
to which E-mail is to be Sent when an
Error Occurs (Mail – Recipient Settings) ......19
Setting Error Items and the URL that are to be
Displayed when an Error Occurs
(Service & Support – Access URL)...............19
Setting up the Projector Using RS-232C or
Telnet .......................................................... 20
When Connecting Using RS-232C.........................20
When Connecting Using Telnet ..............................21
SETUP MENU (Main Menu)....................................22
ADVANCED SETUP MENU ....................................22
View Setting Detail List ([V]View All Setting) ...........23
Set Items ................................................................23
Save Settings and Quit ([S]Save & Quit).................24
Quit without Saving Settings ([Q]Quit Unchanged) ...24
IP Address Setting ([1]IP Address) .........................25
Subnet Mask Setting ([2]Subnet Mask) ..................25
Default Gateway Setting ([3]Default Gateway) .......25
User Name Setting ([4]User Name) ........................25
Password Setting ([5]Password).............................26
RS-232C Baud Rate Setting
([6]RS-232C Baud Rate)...............................26
Projector Name Setting ([7]Projector Name) ..........26
DHCP Client Setting ([8]DHCP Client)....................26
Disconnecting All Connections
([D]Disconnect All) ........................................27
Entering ADVANCED SETUP MENU
([A]Advanced Setup).....................................27
Setting Auto Logout Time
(ADVANCED[1]Auto Logout Time)................27
Data Port Setting (ADVANCED[2]Data Port)...........27
Carrying out Network Ping Test
(ADVANCED[5]Network Ping Test) ...............28
Setting of Accept IP Address (ADVANCED
[6]Accept IP Addr(1) – [8]Accept IP Addr(3)) ..28
Accepting All IP Addresses
(ADVANCED[9]Accept All IP Addr) ...............28
Setting of Search Port
(ADVANCED[0]Search Port)..........................29
Return to Default Settings
(ADVANCED[!]Restore Default Setting) ........29
Return to Main Menu
(ADVANCED[Q]Return to Main Menu)..........29
Resetting the Lamp Timer of the Projector
via LAN ....................................................... 30
Troubleshooting.................................................. 32

-2
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini
D-sub 15 pin female connector
COMPUTER Input/Output COMPUTER Input/Output
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
DVI-I Terminal: 29 pin connector
DVI Digital Input•
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
T.M.D.S data 2–
T.M.D.S data 2+
T.M.D.S data 2 shield
Not connected
Not connected
DDC clock
DDC data
Not connected
T.M.D.S data 1–
T.M.D.S data 1+
T.M.D.S data 1 shield
Not connected
Not connected
+5V power
Ground
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Hot plug detection
T.M.D.S data 0 –
T.M.D.S data 0+
T.M.D.S data 0 shield
Not connected
Not connected
T.M.D.S clock shield
T.M.D.S clock+
T.M.D.S clock–
Not connected
Not connected
Not connected
Not connected
Ground
DVI Analog RGB Input• DVI Analog Component Input•
Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Not connected
Not connected
Not connected
Not connected
Not connected
DDC clock
DDC data
Vertical sync
Not connected
Not connected
Not connected
Not connected
Not connected
+5V power
Ground
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Hot plug detection
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Red
Analog input Green
(Sync On Green)
Analog input Blue
Horizontal sync
(Composite Sync)
Ground
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Ground
16.
17.
18.
19.
20.
21.
22.
23.
24.
C1.
C2.
C3.
C4.
C5.
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Analog input Pr/Cr
Analog input Y
Analog input Pb/Cb
Not connected
Ground
5
10
15
1
11
6
5
10
15
1
11
6
17
24
1823
C3
21
9
16
C1
C2
C4
C5
87
17
24
1823
C3
21
9
16
C1
C2
C4
C5
87

-3
RS-232C Terminal: D-sub 9 pin male connector
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal: Type B USB connector LAN Terminal: LAN (RJ-45)
Pin No. Signal Name Pin No. Signal Pin No. Signal
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1.
2.
3.
4.
TX+
TX–
RX+
5.
6.
7.
8.
RX–
15
69
15
69
51
96
51
96
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
43
12
43
12
8... 18 ... 1
Connecting Pin Assignments

-4
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 24 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)
Command 4-digit Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
OK Return code (0DH) E R R Return code (0DH)
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
•
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
•
•
Note
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.

-5
Commands
Example: When turning on the projector, make the following setting.
Compuer Projector
POWR___1
→
←
OK
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Power On P O W R ___1 OK or ERR OK
Off P O W R ___0 OK OK or ERR
Status POWR????1 0
Projector Condition T A B N ___10:Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64:
Temp Abnormally High
Lamp Status T L P S ___1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Power Status T P O W ___1 1: On, 2: Cooling 0: Standby
Quantity T L P N ___11
Usage Time(Hour) T L T T ___1 0 – 9999(Integer)
Usage Time(Minute) T L T M ___1 0, 15, 30, 45
Life(Percentage) TLTL___1 0% – 100%(Integer)
Name Model Name Check T N A M ___1PGD50X3D/PGD45X3D
Model Name Check M N R D ___1PG-D50X3D/PG-D45X3D
Projector Name Setting 1
(First 4 characters) *1
PJN1****OKorERR
Projector Name Setting 2
(Middle 4 characters) *1
PJN2****OKorERR
Projector Name Setting 3
(Last 4 characters) *1
PJN3****OKorERR
Projector Name Check P J N 0 ___1ProjectorName
Input Change Computer I R G B ___1 OK or ERR ERR
DVI I R G B ___2 OK or ERR ERR
DVI-D-Computer select *2 I B D S ___1 OK or ERR ERR
DVI-D-Video select *2 I B D S ___2 OK or ERR ERR
DVI-Analog select *2 I B D S ___3 OK or ERR ERR
S-Video I V E D ___1 OK or ERR ERR
Video I V E D ___2 OK or ERR ERR
Input RGB Check I R G B ? ? ? ? 1: Computer, 2: DVI or ERR ERR
Input Video Check I V E D ? ? ? ? 1: S-Video, 2: Video or ERR ERR
Input Mode Check I M O D ? ? ? ? 1: RGB, 2: Video ERR
InputCheck ICHK????1:Computer
2: DVI
3: S-Video
4: Video
ERR
Volume Volume(0 – 60) V O L A __**OKorERR ERR
Volume up/down(-10 – +10) V O U D _***OKorERR ERR
Keystone -80 – +80 K E Y S * * * * OK or ERR ERR
AV Mute On I M B K ___1 OK or ERR ERR
Off I M B K ___0 OK or ERR ERR
Freeze On F R E Z ___1 OK or ERR ERR
Off F R E Z ___0 OK or ERR ERR
Auto Sync Start A D J S ___1 OK or ERR ERR
Resize Computer Normal R A S R ___1 OK or ERR ERR
Stretch R A S R ___2 OK or ERR ERR
Dot By Dot R A S R ___3 OK or ERR ERR
Full R A S R ___5 OK or ERR ERR
Border R A S R ___6 OK or ERR ERR
Area Zoom R A S R __10OKorERR ERR
V-Stretch R A S R __11OKorERR ERR
DVI Normal R B S R ___1 OK or ERR ERR
Stretch R B S R ___2 OK or ERR ERR
Dot By Dot R B S R ___3 OK or ERR ERR
Full R B S R ___5 OK or ERR ERR
Border R B S R ___6 OK or ERR ERR
Area Zoom R B S R __10OKorERR ERR
V-Stretch R B S R __11OKorERR ERR
S-Video Normal R A S V ___1 OK or ERR ERR
Stretch R A S V ___2 OK or ERR ERR
Border R A S V ___3 OK or ERR ERR
Area Zoom R A S V __10OKorERR ERR
V-Stretch R A S V __11OKorERR ERR
RS-232C Specifications and Commands

-6
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Resize Video Normal R B S V ___1 OK or ERR ERR
Stretch R B S V ___2 OK or ERR ERR
Border R B S V ___3 OK or ERR ERR
Area Zoom R B S V __10OKorERR ERR
V-Stretch R B S V __11OKorERR ERR
ALL Reset ALRE___1 OK or ERR ERR
Computer INPUT Picture Mode Standard R A P S __10OKorERR ERR
Presentation RAPS__11OKorERR ERR
Movie RAPS__12OKorERR ERR
Game RAPS__13OKorERR ERR
sRGB RAPS__14OKorERR ERR
Contrast -30 – +30 R A P I _* * * OK or ERR ERR
Bright -30 – +30 R A B R _* * * OK or ERR ERR
Red -30 – +30 R A R D _* * * OK or ERR ERR
Blue -30 – +30 R A B E _* * * OK or ERR ERR
Color -30 – +30 R A C O _* * * OK or ERR ERR
Tint -30 – +30 R A T I _* * * OK or ERR ERR
Sharp -30 – +30 R A S H _* * * OK or ERR ERR
CLR Temp -1 – +1 R A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R A W E ___* OK or ERR ERR
Progressive 2D Progressive R A I P ___0 OK or ERR ERR
3D Progressive R A I P ___1 OK or ERR ERR
Film Mode RA I P___2OK or ERR ERR
DNR Off R A N R ___0 OK or ERR ERR
Level 1 R A N R ___1 OK or ERR ERR
Level 2 R A N R ___2 OK or ERR ERR
Picture Reset R A R E ___1 OK or ERR ERR
Signal Type Auto I A S I ___0 OK or ERR ERR
RGB I A S I ___1 OK or ERR ERR
Component I A S I ___2 OK or ERR ERR
Audio Input Audio 1 R A A I ___1 OK or ERR ERR
Audio 2 R A A I ___2 OK or ERR ERR
DVI INPUT Picture Mode Standard R B P S __10OKorERR ERR
Presentation R B P S __11OKorERR ERR
Movie R B P S __12OKorERR ERR
Game R B P S __13OKorERR ERR
sRGB R B P S __14OKorERR ERR
Contrast -30 – +30 R B P I _* * * OK or ERR ERR
Bright -30–+30 RBBR_* * * OK or ERR ERR
Red -30 – +30 R B R D _* * * OK or ERR ERR
Blue -30 – +30 R B B E _* * * OK or ERR ERR
Color -30 – +30 R B C O _* * * OK or ERR ERR
Tint -30 – +30 R B T I _* * * OK or ERR ERR
Sharp -30 – +30 R B S H _* * * OK or ERR ERR
CLR Temp -1 – +1 R B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R B W E ___* OK or ERR ERR
Progressive 2D Progressive R B I P ___0 OK or ERR ERR
3D Progressive R B I P ___1 OK or ERR ERR
Film Mode R B I P ___2 OK or ERR ERR
DNR Off R B N R ___0 OK or ERR ERR
Level 1 R B N R ___1 OK or ERR ERR
Level 2 R B N R ___2 OK or ERR ERR
PictureReset RBRE ___1 OK or ERR ERR
Signal Type Auto I B S I ___0 OK or ERR ERR
RGB I B S I ___1 OK or ERR ERR
Component I B S I ___2 OK or ERR ERR
Audio Input Audio 1 R B A I ___1 OK or ERR ERR
Audio 2 R B A I ___2 OK or ERR ERR
Dynamic
Range
Auto H M B D ___0 OK or ERR ERR
Standard H M B D ___1 OK or ERR ERR
Enhanced H M B D ___2 OK or ERR ERR
S-Video INPUT Picture Mode Standard V A P S __10OKorERR ERR
Presentation VAPS__11OKorERR ERR
Movie VAPS__12OKorERR ERR
Game VAPS__13OKorERR ERR
Contrast -30 – +30 V A P I _* * * OK or ERR ERR
Bright -30 – +30 V A B R _* * * OK or ERR ERR
Red -30 – +30 V A R D _* * * OK or ERR ERR
Blue -30 – +30 V A B E _* * * OK or ERR ERR
RS-232C Specifications and Commands

-7
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
S-Video INPUT Color -30 – +30 V A C O _***OKorERR ERR
Tint -30 – +30 V A T I _***OKorERR ERR
Sharp -30 – +30 V A S H _***OKorERR ERR
CLR Temp -1 – +1 V A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V A W E ___* OK or ERR ERR
Progressive 2D Progressive V A I P ___0 OK or ERR ERR
3D Progressive V A I P ___1 OK or ERR ERR
Film Mode V A I P ___2 OK or ERR ERR
DNR Off V A N R ___0 OK or ERR ERR
Level 1 V A N R ___1 OK or ERR ERR
Level 2 V A N R ___2 OK or ERR ERR
Picture Reset V A R E ___1 OK or ERR ERR
Audio Input Audio 1 V A A I ___1 OK or ERR ERR
Audio 2 V A A I ___2 OK or ERR ERR
Video INPUT Picture Mode Standard V B P S __10OKorERR ERR
Presentation V B P S __11OKorERR ERR
Movie V B P S __12OKorERR ERR
Game V B P S __13OKorERR ERR
Contrast -30 – +30 V B P I _***OKorERR ERR
Bright -30 – +30 V B B R _***OKorERR ERR
Red -30 – +30 V B R D _***OKorERR ERR
Blue -30 – +30 V B B E _***OKorERR ERR
Color -30 – +30 V B C O _***OKorERR ERR
Tint -30 – +30 V B T I _***OKorERR ERR
Sharp -30 – +30 V B S H _***OKorERR ERR
CLR Temp -1 – +1 V B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V B W E ___* OK or ERR ERR
Progressive 2D Progressive V B I P ___0 OK or ERR ERR
3D Progressive V B I P ___1 OK or ERR ERR
Film Mode V B I P ___2 OK or ERR ERR
DNR Off V B N R ___0 OK or ERR ERR
Level 1 V B N R ___1 OK or ERR ERR
Level 2 V B N R ___2 OK or ERR ERR
Picture Reset V B R E ___1 OK or ERR ERR
Audio Input Audio 1 V B A I ___1 OK or ERR ERR
Audio 2 V B A I ___2 OK or ERR ERR
C.M.S. Setting On C M C S __11OKorERR ERR
Off C M C S __00OKorERR ERR
C.M.S. Hue Red C M H R _***OKorERR ERR
Yellow C M H Y _***OKorERR ERR
Green C M H G _***OKorERR ERR
Cyan C M H C _***OKorERR ERR
Blue C M H B _***OKorERR ERR
Magenta C M H M _***OKorERR ERR
Reset C M R E ___2 OK or ERR ERR
Saturation Red C M S R _***OKorERR ERR
Yellow C M S Y _***OKorERR ERR
Green C M S G _***OKorERR ERR
Cyan C M S C _***OKorERR ERR
Blue C M S B _***OKorERR ERR
Magenta C M S M _***OKorERR ERR
Reset C M R E ___3 OK or ERR ERR
Value Red C M V R _***OKorERR ERR
Yellow C M V Y _***OKorERR ERR
Green C M V G _***OKorERR ERR
Cyan C M V C _***OKorERR ERR
Blue C M V B _***OKorERR ERR
Magenta CMVM_***OKorERR ERR
Reset C M R E ___4 OK or ERR ERR
C.M.S. All Reset C M R E ___1 OK or ERR ERR
Clock -150 – +150 I N C L * * * * OK or ERR ERR
Phase -30 – +30 I N P H _***OKorERR ERR
H-position -150 – +150 I A H P * * * * OK or ERR ERR
V-position -60 – +60 I A V P _***OKorERR ERR
Fine Sync Adjustment Reset I A R E ___1 OK or ERR ERR
Image Shift -96 – +96 L N D S _***OKorERR ERR
Overscan On O V S N ___1 OK or ERR ERR
Off O V S N ___0 OK or ERR ERR
OSD Display On I M D I ___1 OK or ERR ERR
Off I M D I ___0 OK or ERR ERR
RS-232C Specifications and Commands

-8
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Video System Auto M E S Y ___1 OK or ERR ERR
PAL M E S Y ___2 OK or ERR ERR
SECAM M E S Y ___3 OK or ERR ERR
NTSC4.43 M E S Y ___4 OK or ERR ERR
NTSC3.58 M E S Y ___5 OK or ERR ERR
PAL-M M E S Y ___6 OK or ERR ERR
PAL-N M E S Y ___7 OK or ERR ERR
PAL-60 M E S Y ___8 OK or ERR ERR
Background Logo I M B G ___1 OK or ERR ERR
Blue I M B G ___3 OK or ERR ERR
None I M B G ___4 OK or ERR ERR
Eco+Quiet On T H M D ___1 OK or ERR ERR
Off T H M D ___0 OK or ERR ERR
Auto Sync On A A D J ___1 OK or ERR ERR
Off A A D J ___0 OK or ERR ERR
Auto Power Off On A P O W ___1 OK or ERR ERR
Off A P O W ___0 OK or ERR ERR
Auto Restart On A R E S ___1 OK or ERR ERR
Off A R E S ___0 OK or ERR ERR
STANDBY Mode Standard M O U T ___1 OK or ERR ERR
Eco M O U T ___0 OK or ERR ERR
PRJ Mode Reverse On I M R E ___1 OK or ERR ERR
Off I M R E ___0 OK or ERR ERR
Invert On I M I N ___1 OK or ERR ERR
Off I M I N ___0 OK or ERR ERR
Language English M E L A ___1 OK or ERR ERR
Deutsch M E L A ___2 OK or ERR ERR
Español M E L A ___3 OK or ERR ERR
Nederlands M E L A ___4 OK or ERR ERR
Français M E L A ___5 OK or ERR ERR
Italiano M E L A ___6 OK or ERR ERR
Svenska M E L A ___7 OK or ERR ERR
ME L A ___8 OK or ERR ERR
Português M E L A ___9 OK or ERR ERR
ME L A __10OKorERR ERR
ME L A __11OKorERR ERR
ME L A __12OKorERR ERR
ME L A __13OKorERR ERR
polski M E L A __14OKorERR ERR
Türkçe M E L A __15OKorERR ERR
ME L A __16OKorERR ERR
Magyar M E L A __17OKorERR ERR
System Sound On S S N D ___1 OK or ERR ERR
Off S S N D ___0 OK or ERR ERR
Audio Out FAO A O U T ___1 OK or ERR ERR
VAO A O U T ___2 OK or ERR ERR
InternalSpeaker On ASPK___1 OK or ERR ERR
Off ASPK___0 OK or ERR ERR
RGB Frequency Check Horizontal T F R Q ___1 kHz(***.* or ERR) ERR
Vertical T F R Q ___2 Hz(***.* or ERR) ERR
Fan Mode Normal H L M D ___0 OK or ERR ERR
High H L M D ___1 OK or ERR ERR
Balance -30 − +30 A A B L _***OKorERR ERR
Treble -30 − +30 A A T E _***OKorERR ERR
Bass -30 − +30 A A B A _***OKorERR ERR
Audio Adjustment Reset A A R E ___1 OK or ERR ERR
DLP®LinkTM Off 3 D E N _ _ _ 0 OK or ERR ERR
On 3 D E N _ _ _ 1 OK or ERR ERR
DLP®LinkTM Invert 3 D I V _ _ _ 1 OK or ERR ERR
Video Setup 0 IRE V I S U _ _ _ 0 OK or ERR ERR
7.5 IRE V I S U _ _ _ 1 OK or ERR ERR
Closed Caption
(For Americas only)
Off C L C A _ _ _ 0 OK or ERR ERR
CC1 C L C A _ _ _ 1 OK or ERR ERR
CC2 C L C A _ _ _ 2 OK or ERR ERR
Lamp Timer Reset *3 L P R E 0 0 0 1 ERR OK or ERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response code is
received.
*3 The Lamp Timer Reset command is available only in standby mode.
RS-232C Specifications and Commands

-9
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector's network settings may need to be
changed. Please consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following
procedure is for making settings on the computer.
Network settings on the computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
LAN cable
(commercially available)
1. Connecting the projector to a computer
Page 10
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
Temporarily change
the computer's IP
address.
2. Setting an IP address for the computer
Pages 11, 12
Adjust the projector network settings to conform to your network.
Use Internet Explorer
(version 5.0 or later)
to make various
projector settings.
3. Setting up a network connection for the projector
Pages 13, 14
Microsoft®, Windows®and Windows Vista®are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E.U.,
China and/or other countries/regions.
All other company or product names are trademarks or registered trademarks of their respective
companies.
•
•
•

-10
1. Connecting the Projector
to a Computer
Establishing a one-to-one connection from
the projector to a computer. Using a
commercially available LAN cable (UTP
cable, Category 5, cross-over type) you can
configure the projector via the computer.
1
Disconnect the computer's LAN
cable from the existing network.
2Connect a commercially available
LAN cable (UTP cable, Category 5,
cross-over type) to the projector's
LAN terminal and connect the
other end of the cable to the
computer's LAN terminal.
3Plug the power cord into the AC
socket of the projector.
4Turn on the computer.
Info
Confirm that the LINK LED on the rear of the
projector illuminates. If the LINK LED does not
illuminate, check the following:
The LAN cable is properly connected.
The power switches of both the projector and
the computer are on.
•
•
1
A LAN cable being
connected to the network
A LAN cable being
connected to the network
2
LAN cable
(cross-over type, commercially available)
LAN cable
(cross-over type, commercially available)
3
4
ONON
This completes the connection. Now proceed to “2. Setting an IP Address for the Computer”.
Setting up the Projector Network Environment

-11
2. Setting an IP Address for
the Computer
The following describes how to make
settings in Windows Vista®.
1Log on the network using the
administrator's account for the
computer.
2Click “start”, and click “Control
Panel”.
3Click “View network status and
tasks” of “Network and Internet”,
and click “View status” in the new
window.
This manual uses examples to explain the
operations in Category View. If you are using
Classic View, double-click “Network and
Sharing Center”.
4Click “Properties”.
When the user account control display is
displayed, click “Continue”.
•
•
1
2
1
2
1
2
3
1
2
1
2
4
11
Setting up the Projector Network Environment
XXXXXXXXX

-12
5Click “Internet Protocol Version 4
(TCP/IPv4)”, and click the
“Properties” button.
6Confirm or change an IP address
for the setup computer.
1Confirm and note the current IP
address, Subnet mask and Default
gateway.
Make sure to note the current IP address,
Subnet mask and Default gateway as you
will be required to reset them later.
2Set temporarily as follows:
IP address: 192.168.150.3
Subnet mask: 255.255.255.0
Default gateway: (Do not input any
values.)
The factory default settings for the projector are
as follows:
DHCP Client: OFF
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
•
Note
7After setting, click the “OK”
button, and then restart the
computer.
5
1
2
1
2
6
7
After confirming or setting, proceed to “3. Setting up Network Connection for the Projector”.
Setting up the Projector Network Environment

-13
3. Setting up a Network Con-
nection for the Projector
Settings for such items as the projector's
IP address and subnet mask are
compatible with the existing network.
Set each item on the projector as follows.
(See page 50 of the projector's operation
manual for setting.)
DHCP Client: Off
IP Address: 192.168.150.002
Subnet Mask: 255.255.255.000
1Start Internet Explorer (version 5.0
or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
2If a user name and a password
have not yet been set, just click
the “OK” button.
If a user name and a password have been
set, input the user name and the password,
and click the “OK” button.
If the user name or password is entered
incorrectly three times, an error message will
be displayed.
When you are using Internet Explorer 7, other
setup screen may be displayed. In this case,
make the proper adjustments for the setup
screen.
3When the screen as shown on the
right appears, click “TCP/IP”.
•
•
•
1
2
3
Setting up the Projector Network Environment

-14
4The TCP/IP setting screen
appears, ready for network
settings for the projector.
Items Setting example / Remarks
New
Password
You can set the password to protect
the TCP/IP setting.
DHCP
Client
Select “ON” or “OFF” to determine
whether to use DHCP Client.
IP
Address
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate for
the network.
Subnet
Mask
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting:
255.255.255.0
Set the subnet mask to the same as
that of the computer and equipment
on the network.
Default
Gateway
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
DNS
Server
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Confirm the existing network's segment (IP
address group) to avoid setting an IP address
that duplicates the IP addresses of other
network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”, you
don't have to change the projector IP address.
For details about each setting, consult your
network administrator.
•
•
Note
5Click the “Apply” button.
6The set values appear. Confirm
that the values are set properly,
and then click the “Confirm”
button.
4
5
6
Setting up the Projector Network Environment
Close the browser.
This completes the network settings.
After setting items, wait for about 15 seconds and then re-access.
Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6-1on page 12, and then connect the computer and the projector to the network.
•
•
•
•

-15
Controlling the Projector via LAN
After connecting the projector to your network, enter the projector IP address in
“Address” on Internet Explorer (version 5.0 or later) using a computer on the network to
start a setup screen that will enable control of the projector via the network.
Controlling the Projector
Using Internet Explorer
(Version 5.0 or later)
Complete connections to external
equipment before starting the operation.
(See pages 21-25 of the projector's
operation manual.)
Complete the AC cord connection. (See
page 25 of the projector's operation
manual.)
When connecting the projector to the LAN, use
a commercially available LAN cable (UTP cable,
Category 5, cross-over type). When
connecting the projector to a hub, use a
straight-through cable.
•
Note
1Start Internet Explorer (version 5.0
or later) on the computer.
2Enter “http://” followed by the
projector IP address set by the
procedure on page 14 followed by
“/” in “Address”, and then press
the “Enter” key.
When “DHCP Client” is set to “OFF” on the
projector, IP address is 192.168.150.2. If you
did not change the IP address in “3. Setting
up a Network Connection for the
Projector” (pages 13-14), enter
“http://192.168.150.2/”.
3A screen for controlling the
projector appears, ready for
performing various status
conditions, control, and settings.
•
1
2
3

-16
Confirming the Projector
Status (Status)
On this screen, you can confirm the
projector status. You can confirm the
following items:
MAC Address
Power
Condition
Lamp Timer
Lamp Life
Input
Signal Info
Serial Number
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
For details about each item, refer to the
projector's operation manual.
•
•
Note
•
•
•
•
•
•
•
•
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector
control. You can control the following
items:
Power
Input Select
Volume
AV Mute
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
You cannot operate this page while the
projector is warming up.
While the projector is in standby mode, you can
only control “Power ON”.
For details about each item, refer to the
projector's operation manual.
•
•
•
•
Note
•
•
•
•

-17
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for COMPUTER
On these screens, you can make projector
settings or adjustments. You can set or
adjust the following items:
Controlling the Projector via LAN
Picture Mode
CLR Temp
BrilliantColorTM
Progressive
DNR
Eco + Quiet Mode
Resolution Setting
Signal Type
Video System
Dynamic Range
Resize
Overscan
OSD Display
Background
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Projection Mode
DLP®LinkTM
DLP®LinkTM Invert
Video Setup
OSD Language
Auto Sync
Auto Power Off
Auto Restart
System Sound
Audio Out
Internal Speaker
Audio Input
RS-232C Speed
Fan Mode
All Reset
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
You cannot operate this page while the
projector is warming up.
For details about each item, refer to the
projector's operation manual.
•
•
•
Note
Setting the Security
(Network – Security)
On this screen, you can make settings
relating to security.
Items Description
User Name Setting of user name for security
protection.
Password Setting of password for security
protection.
Accept IP
Address
It is possible to set up to three IP
addresses allowing connection to the
projector.
All IP
Addresses
No limits are set to IP addresses
connecting to the projector.
From only
specific IP
addresses
For security improvement, only an IP
address set by “Address 1-3” can be
connected to the projector.
User Name and Password can be up to 8
characters.
You can input the characters below:
a-z, A-Z, 0-9, -, _
•
•
Note

-18
Making General Settings for
the Network (Network - General)
On this screen, you can make general
settings relating to the network.
Items Description
Projector
Name
Setting the projector name.
Auto Logout
Time
Setting the time interval in which the
projector will be automatically
disconnected from the network in units
of a minute (from 1 to 65535 minutes).
If the set value is made 0, the Auto
Logout function is disabled.
Data Port Setting the TCP port number used
when exchanging data with the
projector (from 1025 to 65535).
Search Port Setting the port number used when
searching for the projector (from 1025
to 65535).
After clicking the “Apply” button, the set
values appear. Confirm that the values are
set properly, and then click the “Confirm”
button.
After setting items, wait for about 15 seconds
and then re-access.
Projector Name can be up to 12 characters.
You can input the characters below:
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
•
•
•
Note
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the
projector has generated an error.
Items Setting example / Remarks
SMTP Server Setting an SMTP server address for e-
mail transmission.
e.g.1: 192.168.150.253
e.g.2: smtp123.sharp.co.jp
* When using a domain name, make
settings for the DNS server.
Originator E-
mail Address
Setting the projector's e-mail address.
The e-mail address set here becomes
Originator E-mail Address.
Originator
Name
Setting the sender's name. The name
set here appears in the “Originator
Name” column of the body of the
message.
SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
You can input the characters below:
SMTP Server and Originator E-mail Address:
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, },
~, _, ', ., @, `
(You can input “@” only one time for “Originator
E-mail Address”.)
Originator Name: a-z, A-Z, 0-9, -, _, (,), space
If the settings of “3. Setting up a Network
Connection for the Projector” on pages 13
and 14 are incorrectly set, e-mail will not be
sent.
•
•
•
Note
Controlling the Projector via LAN

-19
Controlling the Projector via LAN
Setting Error Items and
Destination Addresses to
which E-mail is to be Sent
when an Error Occurs
(Mail – Recipient Settings)
On this screen, you can input e-mail
destinations to which error notification
(error items) e-mails are sent.
Items Description
E-mail
Address
Set addresses to which error
notification e-mail is sent. You can set
up to five addresses.
Error Mail
(Lamp, Temp,
Fan,Cover)
Error e-mail is sent on the error items
checked in their check boxes.
Test Send test e-mail. This allows you to
confirm that the settings for e-mail
transmission are properly set.
E-mail Address can be up to 64 characters.
You can input the characters below:
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, },
~, _, ', ., @, `
(You can input “@” only one time.)
For details about error items, refer to the
projector's operation manual.
•
•
•
Note
Setting Error Items and the
URL that are to be
Displayed when an Error
Occurs (Service & Support –
Access URL)
On this screen, you can make settings of
the URL and error items that are to be
displayed when the projector has
generated an error.
Items Description
Access URL Set the URL that is to be displayed
when an error occurs. You can set up
to five addresses.
Condition
(Always,
Lamp, Temp,
Fan,Cover)
The URL is displayed when an error
checked in their check boxes occurs.
Test The set URL site is test-displayed. This
allows you to confirm that the URL site
is properly displayed.
Example of the display when an error
occurs

-20
When Connecting Using
RS-232C
1Launch general purpose terminal
emulator.
2Input settings for the RS-232C
port of the terminal emulator as
follows.
Baud Rate : 9600 bps*
Data Length : 8 bit
Parity Bit : None
Stop Bit : 1 bit
Flow Control : None
* This is the factory default setting. If the value
of Baud Rate for the projector has been
changed, set Baud Rate here according to
the changed value on the projector.
3Input “PJS11234” and press the
“Enter” key.
4“OK” is displayed. Input
“PJS25678” and press the “Enter”
key within 10 seconds.
5“User Name:” is displayed. Input
the user name and press the
“Enter” key.
If a user name has not yet been set, just
press the “Enter” key.
6“Password:” is displayed. Input
the password and press the
“Enter” key.
If a password has not yet been set, just press
the “Enter” key.
•
•
1
2
3
4
5
6
Setting up the Projector Using RS-232C or Telnet
Connect the projector to a computer using RS-232C or Telnet, and open the SETUP
MENU on the computer to carry out various settings for the projector.
7Input “setup” and press the
“Enter” key.
SETUP MENU will be displayed.
▼SETUP MENU
-----------------------------SETUP MENU----------------------------
[1]IP Address [2]Subnet Mask [3]Default Gateway
[4]User Name [5]Password
[6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client
[A]Advanced Setup [D]Disconnect All
[V]View All Setting [S]Save & Quit [Q]Quit Unchanged
setup>
User name and password are not set in the
factory default settings.
If the user name or password is entered
incorrectly three times, SETUP MENU will be
quit.
•
•
Note
•
7