Sharp PG-D2710X User guide

MODEL
PG-D3510X
PG-D3010X
PG-D2710X
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments ............................................................ 2
RS-232C Specifications and Commands ......................................... 4
Operating the Projector Using the PJLinkTM Protocol .................. 10
Setting up the Projector Network Environment ............................... 11
1. Connecting the Projector to a Computer ............................................ 12
2. Setting an IP Address for the Computer ............................................. 13
3. Setting up a Network Connection for the Projector ............................ 15
Controlling the Projector via LAN ................................................... 17
Controlling the Projector Using Internet Explorer.................................... 17
Confirming the Projector Status (Status)................................................. 18
Controlling the Projector (Control)........................................................... 18
Setting and Adjusting the Projector (Settings & Adjustments)................ 19
Setting the Security (Network – Security)................................................ 19
Making General Settings for the Network (Network – General)............... 20
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ............................................................ 20
Setting Error Items and Destination Addresses to which E-mail is to be
Sent when an Error Occurs (Mail – Recipient Settings) ................ 21
Setting Error Items and the URL that are to be Displayed
when an Error Occurs (Service & Support – Access URL)............ 21
Resetting the Lamp Timer of the Projector via LAN ..................... 22
Troubleshooting................................................................................ 24

-2
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini
D-sub 15 pin female connector
COMPUTER Input/Output COMPONENT Input/Output
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
RS-232C Terminal: mini DIN 9 pin female connector
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
5
10
15
1
11
6
5
10
15
1
11
6
8
9
6
5
21
4
3
7
8
9
6
5
21
4
3
7
15
69
15
69

-3
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal: Type B USB connector LAN Terminal: LAN (RJ-45)
Pin No. Signal Name Pin No. Signal Pin No. Signal
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1.
2.
3.
4.
TX+
TX–
RX+
5.
6.
7.
8.
RX–
51
96
51
96
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
43
12
43
12
8... 18 ... 1
Connecting Pin Assignments

-4
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 24 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)
Command 4-digit Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
OK Return code (0DH) E R R Return code (0DH)
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
•
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
•
•
Note

-5
Commands
Example: When turning on the projector, make the following setting.
Computer Projector
POWR___1
→
←
OK
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Power On P O W R ___1 OK or ERR OK
Off P O W R ___0 OK OK or ERR
Status POWR????1 0
Projector Condition T A B N ___10:Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64:
Temp Abnormally High
Lamp Status T L P S ___1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Power Status T P O W ___1 1: On, 2: Cooling 0: Standby
Quantity T L P N ___11
Usage Time(Hour) T L T T ___1 0 – 9999(Integer)
Usage Time(Minute) T L T M ___1 0, 15, 30, 45
Life(Percentage) TLTL___1 0% – 100%(Integer)
Name Model Name Check T N A M ___1 PGD3510X/PGD3010X/PGD2710X
Model Name Check M N R D ___1 PG-D3510X/PG-D3010X/PG-D2710X
Projector Name Setting 1
(First 4 characters) *1
PJN1****OKorERR
Projector Name Setting 2
(Middle 4 characters) *1
PJN2****OKorERR
Projector Name Setting 3
(Last 4 characters) *1
PJN3****OKorERR
Projector Name Check P J N 0 ___1ProjectorName
Input Change COMPUTER1 I R G B ___1 OK or ERR ERR
COMPUTER2 *2 I R G B ___2 OK or ERR ERR
S-VIDEO I V E D ___1 OK or ERR ERR
VIDEO I V E D ___2 OK or ERR ERR
InputRGBCheck IRGB????1:COMPUTER1,
2: COMPUTER2 or ERR
ERR
Input Video Check I V E D ? ? ? ? 1: S-VIDEO, 2: VIDEO or ERR ERR
Input Mode Check I M O D ? ? ? ? 1: RGB, 2: VIDEO ERR
InputCheck ICHK????1:COMPUTER1
2: COMPUTER2
3: S-VIDEO
4: VIDEO
ERR
Volume Volume(0 – 60) V O L A __**OKorERR ERR
Volume up/down(-10 – +10) V O U D _***OKorERR ERR
Keystone -80 – +80 K E Y S * * * * OK or ERR ERR
AV Mute On I M B K ___1 OK or ERR ERR
Off I M B K ___0 OK or ERR ERR
Freeze On F R E Z ___1 OK or ERR ERR
Off F R E Z ___0 OK or ERR ERR
Auto Sync Start A D J S ___1 OK or ERR ERR
Resize COMPUTER1 Normal R A S R ___1 OK or ERR ERR
16:9 R A S R ___2 OK or ERR ERR
Native R A S R ___3 OK or ERR ERR
Full R A S R ___5 OK or ERR ERR
Border R A S R ___6 OK or ERR ERR
Area Zoom R A S R __10OKorERR ERR
V-Stretch R A S R __11OKorERR ERR
COMPUTER2 Normal R B S R ___1 OK or ERR ERR
16:9 R B S R ___2 OK or ERR ERR
Native R B S R ___3 OK or ERR ERR
Full R B S R ___5 OK or ERR ERR
Border R B S R ___6 OK or ERR ERR
Area Zoom R B S R __10OKorERR ERR
V-Stretch R B S R __11OKorERR ERR
RS-232C Specifications and Commands

-6
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Resize S-VIDEO Normal R A S V ___1 OK or ERR ERR
16:9 R A S V ___2 OK or ERR ERR
Border R A S V ___3 OK or ERR ERR
Area Zoom R A S V __10OKorERR ERR
V-Stretch R A S V __11OKorERR ERR
VIDEO Normal R B S V ___1 OK or ERR ERR
16:9 R B S V ___2 OK or ERR ERR
Border R B S V ___3 OK or ERR ERR
Area Zoom R B S V __10OKorERR ERR
V-Stretch RBSV __11 OK or ERR ERR
All Reset ALRE___1OK or ERR ERR
COMPUTER1 Input Picture Mode Standard RAPS__10 OK or ERR ERR
Presentation RAPS__11 OK or ERR ERR
Movie RAPS__12 OK or ERR ERR
Game RAPS__13OKorERR ERR
sRGB RAPS__14OKorERR ERR
Contrast -30 – +30 R A P I _* * * OK or ERR ERR
Bright -30 – +30 R A B R _* * * OK or ERR ERR
Red -30 – +30 R A R D _* * * OK or ERR ERR
Blue -30 – +30 R A B E _* * * OK or ERR ERR
Color -30 – +30 R A C O _* * * OK or ERR ERR
Tint -30 – +30 R A T I _* * * OK or ERR ERR
Sharp -30 – +30 R A S H _* * * OK or ERR ERR
CLR Temp -1 – +1 R A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R A W E ___* OK or ERR ERR
Film Mode Auto R A F M _ _ _ 0 OK or ERR ERR
Off R A F M _ _ _ 1 OK or ERR ERR
DNR Level 1 R A N R ___1 OK or ERR ERR
Level 2 RANR___2OK or ERR ERR
Level 3 RANR___3OK or ERR ERR
Picture Reset RARE ___1OK or ERR ERR
Signal Type Auto IASI___0OK or ERR ERR
RGB IASI___1OK or ERR ERR
YPbPr IASI___2OK or ERR ERR
Audio Input AUDIO 1 R A A I ___1 OK or ERR ERR
AUDIO 2 R A A I ___2 OK or ERR ERR
COMPUTER2 Input Picture Mode Standard R B P S __10OKorERR ERR
Presentation R B P S __11OKorERR ERR
Movie R B P S __12OKorERR ERR
Game R B P S __13OKorERR ERR
sRGB R B P S __14OKorERR ERR
Contrast -30 – +30 R B P I _* * * OK or ERR ERR
Bright -30–+30 RBBR_* * * OK or ERR ERR
Red -30 – +30 R B R D _* * * OK or ERR ERR
Blue -30 – +30 R B B E _* * * OK or ERR ERR
Color -30 – +30 R B C O _* * * OK or ERR ERR
Tint -30 – +30 R B T I _* * * OK or ERR ERR
Sharp -30 – +30 RBSH_*** OK or ERR ERR
CLR Temp -1 – +1 RBCT __** OK or ERR ERR
BrilliantColor™ 0 – +2 RBWE ___*OK or ERR ERR
Film Mode
Auto R B F M _ _ _ 0 OK or ERR ERR
Off R B F M _ _ _ 1 OK or ERR ERR
DNR Level 1 RBNR___1OK or ERR ERR
Level 2 R B N R ___2 OK or ERR ERR
Level 3 R B N R ___3 OK or ERR ERR
PictureReset RBRE ___1 OK or ERR ERR
Signal Type Auto I B S I ___0 OK or ERR ERR
RGB I B S I ___1 OK or ERR ERR
YPbPr I B S I ___2 OK or ERR ERR
Audio Input AUDIO 1 R B A I ___1 OK or ERR ERR
AUDIO 2 R B A I ___2 OK or ERR ERR
RS-232C Specifications and Commands

-7
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
S-VIDEO Input Picture Mode Standard V A P S __10OKorERR ERR
Presentation VAPS__11OKorERR ERR
Movie VAPS__12OKorERR ERR
Game VAPS__13OKorERR ERR
Contrast -30 – +30 V A P I _***OKorERR ERR
Bright -30 – +30 V A B R _***OKorERR ERR
Red -30 – +30 V A R D _***OKorERR ERR
Blue -30 – +30 V A B E _***OKorERR ERR
Color -30 – +30 V A C O _***OKorERR ERR
Tint -30 – +30 VAT I _*** OK or ERR ERR
Sharp -30 – +30 VASH_*** OK or ERR ERR
CLR Temp -1 – +1 VACT__** OK or ERR ERR
BrilliantColor™ 0 – +2 VAWE___*OK or ERR ERR
Film Mode Auto VAFM___0OK or ERR ERR
Off V A F M ___1 OK or ERR ERR
DNR Level 1 V A N R ___1 OK or ERR ERR
Level 2 V A N R ___2 OK or ERR ERR
Level 3 V A N R ___3 OK or ERR ERR
Picture Reset V A R E ___1 OK or ERR ERR
Audio Input AUDIO 1 V A A I ___1 OK or ERR ERR
AUDIO 2 V A A I ___2 OK or ERR ERR
VIDEO Input Picture Mode Standard V B P S __10OKorERR ERR
Presentation V B P S __11OKorERR ERR
Movie V B P S __12OKorERR ERR
Game V B P S __13OKorERR ERR
Contrast -30 – +30 V B P I _***OKorERR ERR
Bright -30 – +30 V B B R _***OKorERR ERR
Red -30 – +30 V B R D _***OKorERR ERR
Blue -30 – +30 VBBE_*** OK or ERR ERR
Color -30 – +30 VBCO_*** OK or ERR ERR
Tint -30 – +30 VBT I _*** OK or ERR ERR
Sharp -30 – +30 VBSH_*** OK or ERR ERR
CLR Temp -1 – +1 VBCT__** OK or ERR ERR
BrilliantColor™ 0 – +2 VBWE___*OK or ERR ERR
Film Mode Auto V B F M ___0 OK or ERR ERR
Off V B F M ___1 OK or ERR ERR
DNR Level 1 V B N R ___1 OK or ERR ERR
Level 2 V B N R ___2 OK or ERR ERR
Level 3 V B N R ___3 OK or ERR ERR
Picture Reset V B R E ___1 OK or ERR ERR
Audio Input AUDIO 1 V B A I ___1 OK or ERR ERR
AUDIO 2 V B A I ___2 OK or ERR ERR
C.M.S. Setting On C M C S __11OKorERR ERR
Off C M C S __00OKorERR ERR
C.M.S. Hue Red C M H R _***OKorERR ERR
Yellow C M H Y _***OKorERR ERR
Green C M H G _***OKorERR ERR
Cyan CMHC _*** OK or ERR ERR
Blue CMHB _*** OK or ERR ERR
Magenta CMHM_*** OK or ERR ERR
Reset CMR E ___2OK or ERR ERR
Saturation Red CMS R _*** OK or ERR ERR
Yellow CMS Y _*** OK or ERR ERR
Green C M S G _***OKorERR ERR
Cyan C M S C _***OKorERR ERR
Blue C M S B _***OKorERR ERR
Magenta C M S M _***OKorERR ERR
Reset C M R E ___3 OK or ERR ERR
Value Red C M V R _***OKorERR ERR
Yellow C M V Y _***OKorERR ERR
Green C M V G _***OKorERR ERR
Cyan C M V C _***OKorERR ERR
Blue C M V B _***OKorERR ERR
Magenta CMVM_***OKorERR ERR
Reset C M R E ___4 OK or ERR ERR
C.M.S. All Reset C M R E ___1 OK or ERR ERR
RS-232C Specifications and Commands

-8
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Clock -150 – +150 I N C L * * * * OK or ERR ERR
Phase -30 – +30 I N P H _* * * OK or ERR ERR
H-position -150–+150 IAHP****OKorERR ERR
V-position -60 – +60 IAVP
_***
OK or ERR ERR
Fine Sync Adjustment Reset I A R E ___1 OK or ERR ERR
Image Shift -96 – +96 L N D S _***OKorERR ERR
Overscan On O V S N ___1 OK or ERR ERR
Off O V S N ___0 OK or ERR ERR
OSD Display On I M D I ___1 OK or ERR ERR
Off I M D I ___0 OK or ERR ERR
Video System Auto M E S Y ___1 OK or ERR ERR
PAL M E S Y ___2 OK or ERR ERR
SECAM M E S Y ___3 OK or ERR ERR
NTSC4.43 M E S Y ___4 OK or ERR ERR
NTSC3.58 M E S Y ___5 OK or ERR ERR
PAL-M M E S Y ___6 OK or ERR ERR
PAL-N M E S Y ___7 OK or ERR ERR
PAL-60 ME SY ___8OK or ERR ERR
Background Logo IMBG___1OK or ERR ERR
Blue IMBG___3OK or ERR ERR
None IMBG___4OK or ERR ERR
Eco+Quiet On THMD___1OK or ERR ERR
Off T H M D ___0 OK or ERR ERR
Auto Sync On A A D J ___1 OK or ERR ERR
Off A A D J ___0 OK or ERR ERR
Auto Power Off On A P O W ___1 OK or ERR ERR
Off A P O W ___0 OK or ERR ERR
Auto Restart On A R E S ___1 OK or ERR ERR
Off A R E S ___0 OK or ERR ERR
STANDBY Mode Quick Start M O U T ___1 OK or ERR ERR
Eco M O U T ___0 OK or ERR ERR
PRJ Mode Reverse On I M R E ___1 OK or ERR ERR
Off I M R E ___0 OK or ERR ERR
Invert On I M I N ___1 OK or ERR ERR
Off I M I N ___0 OK or ERR ERR
Language English M E L A ___1 OK or ERR ERR
Deutsch ME L A ___2OK or ERR ERR
Español ME L A ___3OK or ERR ERR
Nederlands ME L A ___4OK or ERR ERR
Français ME L A ___5OK or ERR ERR
Italiano ME L A ___6OK or ERR ERR
Svenska M E L A ___7 OK or ERR ERR
ME L A ___8 OK or ERR ERR
Português M E L A ___9 OK or ERR ERR
ME L A __10OKorERR ERR
ME L A __11OKorERR ERR
ME L A __12OKorERR ERR
ME L A __13OKorERR ERR
polski M E L A __14OKorERR ERR
Türkçe M E L A __15OKorERR ERR
ME L A __16OKorERR ERR
Magyar M E L A __17OKorERR ERR
RS-232C Specifications and Commands

-9
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Setup Guide On S E G U ___1 OK or ERR ERR
Off S E G U ___0 OK or ERR ERR
InternalSpeaker On ASPK___1 OK or ERR ERR
Off ASPK___0 OK or ERR ERR
RGB Frequency Check Horizontal T F R Q ___1 kHz(***.* or ERR) ERR
Vertical T F R Q ___2 Hz(***.* or ERR) ERR
Fan Mode Normal H L M D ___0 OK or ERR ERR
High H L M D ___1 OK or ERR ERR
Input Search *3 Start I S E S _ _ _ 1 OK or ERR ERR
Video Setup 0 IRE V I S U _ _ _ 0 OK or ERR ERR
7.5 IRE V I S U _ _ _ 1 OK or ERR ERR
WallColor Off WLCO _ _ _ 0OKorERR ERR
Blackboard WLCO_ _ _ 1OKorERR ERR
Whiteboard WLCO_ _ _ 2OKorERR ERR
Quick Start Menu On Q S M N _ _ _ 0 OK or ERR ERR
Off Q S M N _ _ _ 1 OK or ERR ERR
COMPUTER2 Select *4 Input R B S E _ _ _ 0 OK or ERR ERR
Monitor Output R B S E _ _ _ 1 OK or ERR ERR
DLP®LinkTM Off 3 D E N _ _ _ 0 OK or ERR ERR
On 3 D E N _ _ _ 1 OK or ERR ERR
DLP®LinkTM Invert 3 D I V _ _ _ 1 OK or ERR ERR
Closed Caption
(For Americas only)
Off C L C A _ _ _ 0 OK or ERR ERR
CC1 C L C A _ _ _ 1 OK or ERR ERR
CC2 C L C A _ _ _ 2 OK or ERR ERR
Reset Network Setting L N R E _ _ _ 1 OK or ERR OK or ERR
Restart Network L R E S _ _ _ 1 OK or ERR OK or ERR
Lamp Timer Reset *5 L P R E 0 0 0 1 ERR OK or ERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 When “COMPUTER2 Select” is set to “Monitor Output”, you may receive an “ERR” response code.
*3 When the next command is sent during input search, you may receive an “ERR” response code, and the
input search is canceled.
*4 When “COMPUTER2” is selected in the INPUT list, “COMPUTER2 Select” cannot be set to “Monitor
Output”.
*5 The Lamp Timer Reset command is available only in standby mode.
RS-232C Specifications and Commands

-10
Operating the Projector Using the PJLinkTM Protocol
The projector conforms with the PJLinkTM standard Class 1.
The commands to be used in controlling the projector by the PJLinkTM protocol are as
shown below.
CONTROL CONTENTS COMMAND RETURN
Power Control Off P O W R _ 0 OK or ERR3
On P O W R _ 1 OK or ERR3
Power Status Query P O W R _ ? 0: Standby Mode
1: Power On
2: Standby (Cooling)
3: Power On (Warming up)
Input List Query I N S T _ ? 11 12 21 22
Input Change COMPUTER1 I N P T _ 1 1 OK or ERR3
COMPUTER2 I N P T _ 1 2 OK or ERR3
S-VIDEO I N P T _ 2 1 OK or ERR3
VIDEO I N P T _ 2 2 OK or ERR3
Input Status Query I N P T _ ? 11: COMPUTER1
12: COMPUTER2
21: S-VIDEO
22: VIDEO
or ERR3
AV Mute Off A V M T _ 3 0 OK or ERR3
On A V M T _ 3 1 OK or ERR3
AV Mute Status Query A V M T _ ? 30: Off
31: On
or ERR3
Lamp Query L A M P _ ? 1st Number: Lamp Usage Time (Hour)
2nd Number: 0: Lamp Off 1: Lamp on
Error Condition Query E R S T _ ? 1st Byte: Fan Error Status
2nd Byte: Lamp Error Status
3rd Byte: Temp. Error Status
4th Byte: Cover Open Status
5th Byte: Not Used, Return 0
6th Byte: Other Error Status
0: No Error Detected
1: Warning
2: Error Detected
Projector Name Query * N A M E _ ? Projector Name
Manufacture Name Query I N F 1 _ ? SHARP
Pruduct Name Query I N F 2 _ ? PG-D3510X/PG-D3010X/PG-D2710X
Other Information Query I N F O _ ? Not used
Class Information Query C L S S _ ? 1
* You can set “Projector Name” at “Making General Setting for the Network (Network-General)” on page 20.
PJLinkTM Authentication:
The password to be used for PJLinkTM is the same as the one you have set in “Setting the Security (Network-
Security)” (page 19). When operating without authentication, do not set a password.
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.