Sharper Image 205895 User manual

Travel Alarm Clock
Item No. 205895
User’s Guide
Thank you for choosing the Sharper Image Travel Alarm Clock.
Please take a moment to read this guide and store it for future
reference.
MAIN FEATURES
IDENTIFICATION OF PARTS
1
32
4710
11
56
1. [ ALARM ON/OFF ] slide switch
- Slide upward to turn on alarm function.
- Slide downward to turn off alarm function.
2. [ SNOOZE / LIGHT ] key
- Press to turn on the backlight with 5 seconds.
- When the alarm sounds, press to stop the current alarm and
enter snooze mode.
3. LCD display
4. [ DOWN ] key
- In setting mode, press to decrease the setting value.
- Press and hold to speed up the setting.
5. [ CLOCK SET ] key
- In normal time mode, press and hold for 2 seconds to enter
normal time setting mode.
- In setting mode, press to set items up or press and hold for
2 seconds to save the setting and return to normal time mode.
6. [ ALARM ] key
- In normal time mode, press and hold for 2 seconds to enter alarm
time setting mode.
- In setting mode, press to set up alarm time.
- After setting mode, press it again to save the setting values.
7. [ UP ] key
- In setting mode, press to increase the setting value.
- Press and hold to speed up the setting.
8. [RESET ] key
9. [RCC ] key
- Press to switch between Celsius and Fahrenheit.
- Press and hold for 3 seconds for manual receiving RC signal or
turn o󰀨 RCC function.
10. Auto night-light slide switch
- Slide to [ ON ] position to activate night-light function. When it
is ON, the backlight will automatically turn on in dim and dark
environment detected by the light sensor. The brightness of night-
light is weaker than normal backlight.
- Slide to [ OFF ] position to turn o󰀨 the night-light function.
11.Battery compartment
- Accommodates 2 AA batteries.
GETTING STARTED
1. Remove the battery door.
2. Insert 2 new AA size batteries into the battery compartment.
Make sure you insert them the right way according to the
polarity information marked on the battery compartment.
3. Replace the battery door.
4. Once the battery is installed, the normal segments of the LCD
will be shown before entering the radio controlled time reception
mode.
5. The RC clock will automatically start scanning for the radio
controlled time signal in 8 seconds.
NOTE:
If no display appears on the LCD after inserting the batteries, press
the [RESET] key by using a metal wire. In some cases, you may not
receive the signal immediately. Due to the atmospheric disturbance,
the best reception often occurs during night time.
SIGNAL RECEPTION INDICATOR
The signal indicator displays signal strength in 4 levels. Wave segment
ashing means time signals are being received. The signal quality
could be classied into 4 types:
or
No signal quality Weak signal quality
Acceptable signal quality Excellent signal quality
Note:
1. This unit will automatically search for the time signal at 2:00am,
8:00am, 2:00pm and 8:00pm per day.
2. Always place the unit away from interfering sources such as TV
set, computer, etc.
3. Avoid placing the unit on or next to metal plate.
4. Closed area such as airport, basement, tower block or factory is
not recommended.
5. Do not start reception on a moving article such as vehicle or train.
6. You can press and hold the [RCC] key for 3 seconds to receive
the time signal manually. The receive mode will be off automatically
after 6-16 minutes. Receive mode consumes more battery power
that may reduce battery lifetime.
TIME AND CALENDER SETTING
Note: If the clock does not receive the time signal successfully, you
can set the time manually. As soon as the transmitter is received
again, the clock will automatically synchronize with the received time.

USING ALARM AND SNOOZE FUNCTION
1. Set the alarm time as described in the above section.
2. Slide [ALARM ON/OFF] switch to ON position to turn on alarm
function with the alarm icon []displayed on the LCD.
3. Slide [ALARM ON/OFF] switch to OFF position to turn o󰀨 alarm
function.
Note:
1. When the alarm is sounding, the sound will keep going
for 1 minute without any operation, and it will sound again at
the alarm time next day.
2. Press [SNOOZE/LIGHT] to enter snooze with the bell icon
flashing, the 4 step crescendo alarm will sound 4 times in
every 5 minutes interval (once alarm and 4 times snooze).
The sound duration is 1 minute without any operation.
BATTERY REPLACEMENT
When the LCD becomes dim, replace with 2 new AA size batteries at
once. Pay attention to the battery polarity.
Note: Attention! Please dispose of the used unit or batteries in an
ecologically safe manner.
SPECIFICATION
MAIN UNIT
Operating temperature range: -5°C~50°C
23° F~122°F
Resolution: 0.1°C/°F (above -10°C/14°F)
1°C/°F (below -10°C/14°F)
POWER
Main unit: 3V, use 2 x AA 1.5V (alkaline battery
recommended)
DIMENSION
Main unit: 96.5(W) x 88(H) x 34(D) mm
1. In normal time mode, press and hold [CLOCK] key for 2
seconds until the Year digit ashes.
2. Press [UP] or [DOWN] key to set desired value of the ashing
Year digit, press [UP] or [DOWN] key without releasing to speed
up the setting.
3. Press [CLOCK] key again to conrm the desired value and go to
next setting.
4. Repeat the above operations to set the time and calendar in this
order: Time zone > Year > Month > Date > 12/24 Hour format
> Hour > Minute > Second > Language: GB (English) /
FR (French) / DE (German) / ES (Spanish) / IT (Italian).
5. Press and hold [CLOCK] key for 2 seconds to save and exit the
setting, or let it exit automatically 30 seconds later without
pressing any key.
Normal time mode
Language setting
Second setting
Year setting
Month setting
Date setting
Time zone setting
Minute setting Hour format settingHour setting
Note:
When adjusting the value of seconds, press [UP] or [DOWN] key
to clear the value to 00.
ALARM TIME SETTING
1. In normal mode, press and hold [ALARM] key for 2 seconds until
the Hour digit flashes.
2. Press [UP] or [DOWN] key to set the desired value, press [UP]
or [DOWN] key without releasing to speed up the setting.
3. Press [ALARM] key to minute setting and then press [UP] or
[DOWN] key to adjust its value.
4. Press [ALARM] key again to save and exit the setting, or let it
exit automatically 30 seconds later without pressing any key.
Normal time mode Hour settingMinute setting The SHARPER IMAGE® name and logo are registered trademarks.
©Sharper Image. All Rights Reserved.
Sharper Image branded items purchased from SharperImage.com
include a 1-year limited replacement warranty. For Customer
Service, please call 1 [phone].
IMPORTANT NOTE
This clock syncs using radio station WWVB near Ft. Collins,
Colorado. You may sync it manually during the initial set up or
simply leave the clock running overnight to automatically set the
time and date. User may be required to select the Time Zone
depending on your location.
WARRANTY/CUSTOMER SERVICE