Sharper Image 206169 User manual

Item No. 206169
NOISE CANCELLING BLUETOOTH HEADPHONES
Owner’s Guide
Thank you for choosing the Sharper Image Noise Cancelling Bluetooth Headphones.
Please take a moment to read this guide and store it for future reference.
FEATURES
HOW TO CHARGE THE HEADPHONE BATTERY
• Bluetooth 4.1
• Noise cancelling technology
• Pairs easily with all iPhones, iPads, Samsung Galaxies and other Android devices
• Over 20 hours play time
• Built-in microphone for hands-free phone calls
• Includes airline adapter for wired use
• Includes travel pouch
1. Open the rubber plug on the USB port.
2. Connect the USB port of your headphones with the USB port of your computer, USB
charger or etc. Use a suitable USB charging cable for this (type A plug to a type
micro B plug). The LED will pulse in white during the charging process.
The brightness of the LED indicates the charge status. The brighter the LED,
the higher the charge status. Once the battery is fully charged, the LED will illuminate
continuously in white.
3. Take the USB charging cable out of the USB port of the headphones and put
the rubber plug back in place. The LED will go out.
- 1 -

- 2 -
1. Set the sliding switch to position B or C. The headphones will then be in pairing mode.
The LED will blink blue.
2. If the LED doesn’t blink blue, hold the MFB button down for 2 seconds. Pairing mode
will now be reactivated and the LED will blink blue.
3. Turn on the Bluetooth function on your device (e.g. smartphone).
4. Your smartphone will search for Bluetooth devices, and “SI Audio” should appear in
the detected devices list.
5. Select “SI Audio” from the list. If your device requires the entry of a PIN code, enter the
PIN code “0000” set by factory default. A signal tone will sound if the headphones and
your Bluetooth device are connected.
6. To terminate the Bluetooth® connection, switch off the Bluetooth function on your device.
HOW TO CHARGE THE HEADPHONE BATTERY (CONT’D)
BLUETOOTH PAIRING
NOTE: LED will flash in white and a signal tone will sound during low battery level in Bluetooth
mode. Before using the headphones, you must fully charge the battery and connect the headset
to your Bluetooth device. Charge time is 2.5 hours.
Bluetooth mode only works if no cable has been connected. As soon as you connect the
headphones to a USB charger to charge or operate the headphones via a connector cord,
Bluetooth mode will automatically be deactivated. You can connect compatible devices such as
most smartphones with your headphones via Bluetooth. The audio output of your smartphone
is then emitted via Bluetooth.
HOW TO RECONNECT HEADPHONES
HOW TO RESET HEADPHONES
If your headphones have been previously connected with your smartphone, enabling the Bluetooth
function on your smartphone is all you have to do to connect the two devices.
To reset the Bluetooth pairing settings, move the sliding switch to position B or C. Hold down the
MFB and Vol - simultaneously for approximately 4 seconds. The LED will blink twice in blue and the
Bluetooth pairing settings will have been reset.

- 3 -
Moving the sliding switch on your headphones activates the following functions:
• Position A: Bluetooth and ANC are disabled.
• Position B: Bluetooth is enabled (LED is illuminated in blue).
• Position C: Bluetooth and ANC are enabled (LED briefly blinks blue twice).
NOTE: If you connected the headphones via a cable, you can activate the ANC function by
moving the sliding switch to position C.
HEADPHONES CONTROL WHILE CONNECTED WITH SMARTPHONES
ACTIVE NOISE CANCELLATION FUNCTION CONTROL
SPECIFICATIONS
Headphones function Control List
Accept incoming call Press MFB once
Reject incoming call Press and hold the MFB for 2 seconds
End the current call Press MFB once
Mute the current call Press both Vol + & Vol - once
Hold the current call and accept incoming call Press the MFB once during the incoming call
Voice dialing Press and hold the MFB for 2 seconds when
smart phone is standby
Redial last number Press both Vol + & Vol - for 3 seconds
Adjust volume up Press Vol + button
Adjust volume down Press Vol - button
Play or pause music Press the MFB Once
Go to the next track Press & hold the Vol + button for 2 seconds
Go to the previous track Press & hold the Vol - button for 2 seconds
Dimensions: 180*165*80mm
Ear-cup housing dimensions 54*74*50mm
Slider arm dimensions 58*73*15mm
Headband dimensions 156*102*21mm
Headphone weight around 254.3g
Speaker type Φ40mm, 32 Ω Neodymium Driver

- 4 -
Sharper Image branded items purchased from SharperImage.com include a 1-year limited
replacement warranty. For Customer Service, please call 1 [phone].
WARRANTY/CUSTOMER SERVICE
If you have any questions not covered in this Product Manual, please call
Sharper Image Customer Service at 1 [phone].
SPECIFICATIONS
Rated input Power 20 mW
Max. input Power 30 mW
Max. power 200 mW
Frequency response 20Hz to 20kHz
Sensitivity 88± 3dB (IEC-318 coupler at 1kHz1Mw, ANC ON)
/ 85± 3dB (IEC-318 coupler at 1kHz1Mw, ANC
OFF)
L/R Channel imbalance ≤3dB at 1KHZ
ANC performance >-18dB
Bluetooth specification V4.1 with Apt-X codec
Bluetooth solution CSR8645
Bluetooth interface HSP, HFP, A2DP, AVRCP
Charger input voltage 5V
Battery Li-ion Polymer, 610mAh, 3.7V
Play time ≥20hrs(While BT & ANC are working at middle
volume)
Time to fully charge 2.5hrs