Shehds LED Spot 75W Lighting With 3 Face Prism User manual

1
1.Please keep the light in dryness and avoiding use in wet place.
2.Using intermittenlly can be extended the life.
3.Attention to clean the fan and lens usually in order to get the ventilating effects and lighting effects
better.
4.Please do not wipe the crust using organic menstruum for avoid to damaged the product.
-Statement
The product has well capability and intact packing when leave factory,All of the user should comply
with above warning item and manual ,any misuse cause of the damages are not included in our
guarantee,and also can’t be responsible for any malfunction & problem owing to ignore the manual.
Please forgive that we will not be notice for technical change.
LED Spot 75W Lighting With 3 Face Prism

2
-Attention Item
1.For guarantee the life of product,please do not put it on the wet place and not use it the place over
40 degree.
2.Please don’t lay the product on the un-fixable or shakable place.
3.Ask for the professional to maintain the product in order to avoid the danger of get an electric
shock.
4.Power supply should not be changed over +&-10% while the light is using,it will be decreased the
life of lamp if the power is too high,but it will be influenced the luminosity if the power is too low.
5.After power off,if it is need used again,please cool down over 20 minuter.
6.Please look round the manual for ensure the product can be used normally.
-Display Control Instruction
Welcome to use our light.The light uses energy-saving LED,long Product life,shockproof,dustproof,
DMX receiver and self-running feature, which can produce a variety of vivid lighting effects,easy to
operate, suitable for all types of entertainment decoration,architectural lighting industry.
-Product Introduction
Power Supply:AC90--275V,50--60HZ
Power Consumption:75W
Fixing Lamp:LED 75W
Beam Angle: 25-30 degrees
DMX-Control-Channels:10/13 DMX Channels
Pan: Horizontal 540 °
Tilt: Vertical 270 °
P/T Fine: 8-16bit
Prism: 3-Face Rotatable prism
Focusing: Electronic linear focusing from near to far
Shuttle:Flash rate:0--16HZ
Dissipate heat：Air / convective heat transfer
Dimmer:0-100% mechanic dimmer
Long Lifespan LEDs(more than 60,000 hours)
Color wheel:7 colors + blank
GOBO:7 patterns + blank, 2 of which are glass patterns
Data input and output: 3-core XLR plug audio socket

3
1.Set
Menu
Submenu
Detail
Addr
A001-a512
Set DMX Address code
chnd
10ch--13ch
10/13 channel mode
slnd
Mast--slav
Master&Slave：Receiving signals from DMX
shnd
Soun--auto
Sound control /Auto mode
sens
0--100
Sound control sensitive range
led
On--Off
Backlight LED On/Off
disp
Display Invert
pan
On--Off
Pan Invert
tilt
On--Off
Tilt Invert
tenp
Top lamp temperature range
load
On--Off
Restore default values
2.Manu
This interface is used to control the current lamp.
Press the OK key to enter the editing state. Press the UP and DOWN keys to change the channel value.
Press the MENU key to exit the edit status.
13ch DMX Channel Summary
Channel
Function
Value
Function
CH1
Pan
0-255
Pan 540°
CH2
PF
0-255
Pan fine 2°
CH3
Tilt
0-255
Tilt 270°
CH4
TF
0-255
Tilt fine 2°
CH5
P/T Speed
0-255
Pan and Tilt rotation speed
CH6
Dimming
0-255
Total dimming
CH7
Strobe
16-251
Strobe frequency
CH8
Color
0-255
Color Wheel
CH9
Gobo
0-255
Gobo Wheel
CH10
Focus
0-255
Pattern focus
CH11
Prism
16-127
Prism switch
128-255
Prism rotation
CH12
Motor auto
0-255
Motor auto mode

4
CH13
Full auto
150-249
Full auto
Sound
200-249
Sound active mode
Reset
250-255
Reset
10ch DMX Channel Summary
Channel
Function
Value
Function
CH1
Pan
0-255
Pan 540°
CH2
Tilt
0-255
Tilt 270°
CH3
Dimming
0-255
Total dimming
CH4
Strobe
16-251
Strobe frequency
CH5
Color
0-255
Color Wheel
CH6
Gobo
0-255
Gobo Wheel
CH7
Focus
0-255
Pattern focus
CH8
Prism
16-127
Prism switch
128-255
Prism rotation
CH9
Motor auto
0-255
Motor auto mode
CH10
Full auto
150-249
Full auto
Sound
200-249
Sound active mode
Reset
250-255
Reset
CAUTION!
Disconnect from mains before starting maintenance operation.
In order to make the lights in good condition and extend the life time, we suggest are gular cleaning
to the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to
accumulation of dust.2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure that the
circuit contacts are in good condition, prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth,Never use
alcohol or solvents.There are no serviceable parts inside the device. Please refer to the instructions
under "Installation instructions" .Should you need any spare parts,please order genuine parts from
your local dealer