Shelly Plug S Installation and operating manual

SHELLY PLUG S
USER AND SAFETY GUIDE
Shelly® Plug S by Allterco Robotics is intended to be placed into a standard Plug
Type F (IEC) in order to control the electric power through it. Shelly may work as a
standalone device or as an accessory to a home automation controller.
Specification
• Power supply: 110-230V ±10% 50/60Hz AC • Max load: 12A / 230V, 50/60Hz
• Complies with EU standards: RE Directive 2014/53/EU, LVD 2014/35/EU, EMC
2014/30/EU, RoHS2 2011/65/EU
• Working temperature: -20°÷40 °C
• Radio signal power: 1mW
• Radio protocol: WiFi 802.11 b/g/n
• Frequency: 2412-2472 MHz(max. 2483.5 MHz); • Operational range: up to 50 m
outdoors or up to 30 m indoors
• Dimensions (HxWxL): 70x44x 44 mm. • Electrical consumption: < 1W
• SAR: 1.15 W/Kg
Technical Information
• Control through WiFi from a mobile phone, PC, automation system or any other
Device supporting HTTP and/or UDP protocol.
• Microprocessor management.
⚠CAUTION! Danger of electrocution. Connecting the device to the power grid has to
be performed with caution.
⚠CAUTION! Do not allow children to play with the device, especially with the Power
Button. Keep the devices for remote control of Shelly (mobile phones, tablets, PCs)
away from children.
Introduction to Shelly
Shelly® is a family of innovative Devices, which allow remote control of electric

appliances through mobile phone, PC or home automation systems. Shelly® uses
WiFi to connect to the devices con
trolling it. They can be in the same WiFi network or they can use remote access
(through the Internet). Shelly® may work standalone, without being managed by a
home automation controller, in the local WiFi network, as well as through a cloud
service, from everywhere the User has Internet access. Shelly® has an integrated
web server, through which the User may adjust, control and monitor the Device.
Shelly® has two WiFi modes - Access Point (AP) and Client mode (CM). To
operate in Client Mode, a WiFi router must be located within the range of the
Device. Shelly® devices can communicate directly with other WiFi devices through
HTTP protocol .An API can be provided by the Manufacturer. Shelly® devices may
be available for monitor and control even if the User is outside the range of the
local WiFi network, as long as the WiFi router is connected to the Internet. The
cloud function could be used, which is activated through the web server of the
Device or through the settings in the Shelly Cloud mobile application. The User
can register and access Shelly Cloud, using either Android or iOS mobile
applications, or any internet browser and the web site: https://my.Shelly.cloud/.
Installation Instructions
⚠CAUTION! Danger of electrocution. Even when the device is turned off, it is
possible to have voltage across its clamps.
⚠CAUTION! Do not connect the Device to appliances exceeding the given max load!
⚠CAUTION! Before beginning the installation please read the accompanying
documentation carefully and completely. Failure to follow recommended
procedures could lead to malfunction, danger to your life or violation of the law.
Allterco Robotics is not responsible for any loss or damage in case of incorrect
installation or operation of this device.
⚠CAUTION! Use the Device only with power grid and appliances which comply with
all applicable regulations. Short circuit in the power grid or any appliance
connected to the Device may damage it.
⚠CAUTION! The Device may be connected to and may control electric circuits and
appliances only if they comply with the respective standards and safety norms.
Factory Reset
You can return your Shelly Plug to its Factory Settings by pressing and holding the
Button for 10 seconds. Upon successful factory reset Shelly’s WiFi LED will flash
Red/Blue.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly Plug
S is in compliance with Directive 2014/53/EU, 2014/35/EU, 2004/108/ WE,
2011/65/UE. The full text of the EU declaration of conformity is available at the
following internet address
https://shelly.cloud/knowledge-base/devices/shelly-plug-s/
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: [phone]
E-mail: [e-mail]

Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device http://www.shelly.cloud All rights to trademarks She® and
Shelly® , and other intellectual rights associated with this Device belong to
Allterco Robotics EOOD.
Initial Inclusion
Place Shelly into the power socket without any device/load connected to the Shelly.
Press the Power Button. The LED should flash red/blue. This means that Shelly is in
AP mode. Press the Button again and the LED will turn off. This means that Shelly is
turned off.
LED States
• Blue flashing quickly - AP Mode
• Blue flashing slowly - STA Mode (no cloud)
• Blue still - STA Mode (connected to cloud)
• Red still - Rely On
• Red & Blue flashing quickly - FW Update
Some of the features of the Shelly Cloud mobile application are available at
https://my.shelly.cloud/ as well.
Control your home with your voice
All Shelly devices are compatible with Amazons’ Alexa and Goggles' Assistant.
Please see our step-by-step guides on: https://shelly.cloud/compatibility/
Shelly application

Shelly Cloud gives you the opportunity to control and adjust all Shelly® Devices from
anywhere in the world. You only need an internet connection and our mobile
application, installed on your smartphone or tablet.
Registration
The first time you load the Shelly Cloud mobile app, you have to create an account
which can manage all your Shelly® devices.
Forgotten Password
In case you forget or lose your password, just enter the e-mail address you have
used in your registration. You will then receive instructions to change your
password.
⚠WARNING! Be careful when you type your e-mail address during the registration, as
it will be used in case you forget your password.
First steps
After registering, create your first room (or rooms), where you are going to add and
use your Shelly devices. Shelly Cloud gives you the opportunity to create scenes for
automatically turning on or off of the Devices at predefined hours or based on other
parameters like temperature, humidity, light etc. (with available sensors in Shelly
Cloud). Shelly Cloud allows easy control and monitoring using a mobile phone, tablet
or PC.

Device Inclusion
To add a new Shelly device, install it to the power grid following the Installation
Instructions included with the Device.
Step 1
After the installation of Shelly following the Installation Instructions and the power is
turned on, Shelly will create its own WiFi Access Point (AP).
⚠WARNING! If the LED does not flash red/blue, press and hold the Button for at least
10 seconds. The LED should then flash red/blue. If not, please repeat or contact our
customer support at: [e-mail]
Step 2
Choose “Add Device”. In order to add more Devices later, use the app menu at the top
right corner of the main screen and click “Add Device”. Type the name (SSID) and
password for the WiFi network, to which you want to add the Device.

Step 3
If using iOS: you will see the following screen:
Press the home button of your iPhone/iPad/ iPod. Open Settings > WiFi and connect
to the WiFi network created by Shelly, e.g. shelly1- 35FA58. If using Android your
phone/tablet will automatically scan and include all new Shelly Devices in the WiFi
network that you are connected to.

Upon successful Device Inclusion to the WiFi network you will see the following
pop-up:
Step 4
Approximately 30 seconds after discovery of any new Devices оn the local WiFi
network, а list will be displayed by default in the “Discovered Devices” room.

Step 5
Enter Discovered Devices and choose the Device you want to include in your
account.
Step 6
Enter a name for the Device (in the Device Name field). Choose a Room, in which the
Device has to be positioned. You can choose an icon or add a picture to make it
easier to recognize. Press “Save Device”.

Step 7
To enable connection to the Shelly Cloud service for remote control and monitoring
of the Device, press “YES” on the following pop-up.

Shelly devices settings
After your Shelly device is included in the app, you can control it, change its settings
and auto mate the way it works.
To switch the device on and off, use the Power button. To enter the details menu of
the device, click on it’s name. From there you may control the device, as well as edit
its appearance and settings.