Shinybow USA SB-5645AK User manual

SB-5645AK
4x4 HDMI Matrix Switch with Auxiliary Audio I/O
INSTRUCTION MANUAL
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided HDMI Locking Post
replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws
without installing the HDMI Locking Post replacement screws will void your warranty.

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

CONTENTS
INTRODUCTION ..............................................................1
FEATURES & CONTENTS............................................... 2
SPECIFICATIONS ............................................................3
FRONT PANEL ................................................................4
BACK PANEL .................................................................10
REMOTE CONTROL .....................................................12
RS-232 / ETHERNET SERIAL INTERFACE ..................14
EDID FUNCTIONS .........................................................15
IR EXTENDER ...............................................................18
TYPICAL APPLICATION ...............................................19
INTRODUCTION
The SB-5645AK is a professional 4x4 matrix routing switch.
Supporting (4) HDMI Inputs and (4) Auxiliary Audio Inputs and (4)
HDMI Outputs and (4) SPDIF audio Outputs. The SB-5645AK is
based on HDMI standards and supports full resolution HDMI video
with embedded EDID, with a signal bandwidth of 340Mhz, so there
is no signal degradation. High Denition Digital signals can be
selected and distributed to any of the (4) Inputs to the (4) outputs.
The switcher is certied as being fully CEC, ARC and HDCP 1.3
compliant with HDMI 1.4a, 4K2K@30Hz, DVI 1.0 and 3D formats
with a wide frequency range 25MHz~340MHz. Using the build-
in HDMI signal booster function, the HDMI output is capable of
driving cable lengths for 1080p up to 98 feet (30M) & 4K2K@30Hz
up to 66 feet (20M). Supports UXGA/WUXGA/DVI 1920x1200
resolutions to any HD displays. The EDID management can be
selected between (7) different modes. Control is provided via front
panel push buttons, IR remote, RS-232 or TCP/IP (not a web-
browser). A RS-232 Windows GUI interface is also provided for
matrix routing control (Windows only).
1
HDMI-AUDIO MATRIX SWITCHER SERIES
Thank you for purchasing the SB-5645AK HDMI Matrix Switch with Auxiliary. You will nd this unit easy to install and highly
reliable but it is essential that you read this manual thoroughly before attempting to use 4x4 HDMI Matrix switcher.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent.
© Copyright 2016. All Rights Reserved.
Version 1.4 JULY 2015
5645AK-20150630-001
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must
use the provided HDMI Locking Post replacement
screws to keep the internal HDMI jack secure.
Removing the HDMI screws without installing the
HDMI Locking Post replacement screws will void
your warranty.
LOOK A PUPPY!! NOW READ THIS!!

FEATURES
• (4) HDMI with Auxiliary Audio (Analog Audio) Inputs to (4) HDMI with S/PDIF Output destinations
• HDMI digital video w/ embedded HDCP, DVI formats and CEC/HDCP 1.3 compliant
• Worldwide EDID control modes for HDMI full 4K2K@30Hz HD Video resolutions
• Wide frequency range: 25MHz ~ 340MHz, Supports HDMI 4K2K@30Hz, 1.4a 3D formats
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,
1080i/p & 4K2K@30Hz
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio ampliers
• Digital Video TMDS formats resolutions up to 4K2K@30Hz with Deep color 36-bit
• Digital Audio supports Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2, LPCM2
• Audio Input supports Auxiliary Audio (Analog stereo audio)
• Audio Output supports digital audio ARC or digital audio S/PDIF ( from a HDMI source or Auxiliary Audio)
• Various User Interface Control:
• Windows based GUI control via RS-232 interface control driver for 2000/XP/WIN7-32/WIN7-64/WIN8
• Front panel push button
• IR remote control
• Ethernet switch control
• Third party RS-232 control (via simple ASCII)
• Supports world wide (9) control function keys: Full function front panel controls: ARC / AUX/ ALL / OFF / EDID / LOCK / RECALL /
MEMORY / ENTER
• Supports (7) EDID Modes:
• Embedded EDID modes: FSS/ H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz
• External modes: Learning mode
• Automatic scanning of input & output status via LCM display on the front panel
• Using the build-in HDMI signal booster function, the HDMI output is capable of driving cable lengths for 1080p up to 98 feet (30M) &
4K2K@30Hz up to 66 feet (20M)
• Supports Universal power adaptor 12VDC, 5A, (AC100V~AC240V, 50/60Hz)
The switcher will remember that last state during a power cycle. When power is removed and resorted, the last conguration will be invoked.
PACKAGE CONTENTS
Check that you have the following components:
• SB-5645AK Matrix Switcher
• RS-232 V2.0 / Ethernet V2.0 Protocol Instructions
• IR Remote Control (SW-HD44AK)
• 19 inch Ear mount bracket (Part # 1U-440L)
• SB-100 IR Extender Receiver Set
• CD Contents: Manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6 feet (2M)
• HDMI Locking Post Replacement Screws
• Users Guide
• Power Supply Input: DC12V, 5A, (Worldwide Universal 100~240VAC, AC 50/60Hz)
• Optional: SB-100C IR Extender Receiver Cable (6.5ft (2M))
2
FEATURES

SPECIFICATIONS
• Type of HDMI Switcher: (4) Inputs to (4) Outputs HDMI Matrix with Audio and Extension
• HDMI Support: HDMI 4K2K@30Hz, 1080p@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats
• HDCP / CEC Support: HDCP 1.3 Compliant, CEC Compliant
• Video Bandwidth: Wide frequency 25MHz ~ 340Mhz
• Digital Video Support: HD: 480i/ 480p/ 720p/ 1080i/p and 4K2K@30Hz up to 36bit deep color
• Video Inputs: (4) HDMI (HDMI or DVI digital source)
• Audio Inputs: (4) AUX Audio ( Analog Stereo, AUX port. 3.5mm Jack)
• Video Outputs: (4) HDMI: With Booster Output for 1080p up to ~98 ft (30M) & 4K2K@30Hz up to ~66 ft (20M)
• Audio Outputs:
• (4) S/PDIF: Multi Audio Formats 5.1 from HDMI or LPCM-2CH from Auxiliary audio
• (4) ARC: TV Return Channel Audio
• (4) HDMI: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6CH, DTS-
HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Switch Controls:
• Select & Function buttons on front panel (Data status via LCM panel display)
• IR Remote Control (switch control)
• IR External port (switch control via 3.5mm OD Jack)
• RS-232 series interface (switch control)
• Ethernet series interface (switch control)
• Source Status: Input status LEDs indicates presence of a live signal
• (17) Function Control Keys: 1. ARC, 2. AUX, 3. ALL, 4. OFF, 5. RECALL, 6. ENTER, 7. MEMORY, 8. LOCK, 9. EDID, 10. Destination
button 1 thru 4, 11. Source button 1 thru 4
• (7) EDID Management Modes:
• 1. Select Embedded EDID Modes: Mode1: FSS, Mode2: H24-3D, Mode3: H24-3D-M, Mode4: H36-3D, Mode5: H36-3D-M,
Mode6: 4K2K-3D, PCM-2CH, Mode7: DVI-D 1920x1200-60Hz
• 2. Select LEARNING Mode: Learning Destination EDID to Link Source
• Infrared Frequency: 38Khz
• IR External Distance: ~984 feet / 300M maximum
• HDMI I/O Connector: HDMI Type A - SMD 19pin female type
• Temperature: 32°F - 100°F Operation (0°C - 38°C)
• Dimensions (LxWxH): 17.5 x 10 x 1.75 in
• Rack Mount: 1RU High 19in Rack Mount #1U-440L (with rack mount)
• Power Supply: DC12V, 5A, Power Input: AC 100~240VAC 50/60Hz (universal type)
• Safety Approvals: CE, FCC, RoHS, REACH
• Weight: 6.8 lb (Unit only) / 9.8 lb (Net)
As product improvements are continuous, specications are subject to change and without notice.
3
SPECIFICATIONS

4
FRONT PANEL
FRONT PANEL
1. POWER SWITCH: The power switch turns the unit on and off. The LED will illuminate blue to indicate that the switcher is ON and
is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last
conguration will be evoked.
2. STATUS DISPLAY: Front panel status display shows current matrix routing conguration. This same display also shows particular
conguration settings depending on your current function. In run mode (as shown above), the display shows each Output (destination)
channel to which Input (source) it is assigned.
3. IR SENSOR: The IR sensor receives IR commands from the supplied remote control or third party IR emitter.
4. INPUT STATUS DISPLAY: Input sources 1 to 4 LED illuminates blue to indicate that a video source is present on that input.
5. SOURCE SELECT BUTTONS: Separate inputs 1 thru 4 select buttons are provided for each source selection.
6. EDID MODE SELECT BUTTONS: Used to select EDID mode using Source buttons #1 or #2.
7. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 4 select buttons are provided for each destination assignment. Routing can be
source to destination or one source to multiple destinations.
Example: Press Destination 1,3,4. Then press Source 2, it will route Input 2 to Output 1,3,4 respectfully.
8. 19 INCH EAR MOUNT PAIR: Converts desktop to 19 inch rack mount. Bracket (part number: 1U-440L) INCLUDED. Image shows rack
mount bracket attached.

5
FRONT PANEL
FRONT PANEL
9. FUNCTION KEY - ARC:
Audio Return Channel (ARC) is a feature that sends audio from the TV back down the HDMI
cable to its source device, in this case, the switcher. Not all displays support ARC, check your
Users Guide for additional information. (Default = ARC Disabled)
The “Audio & ARC” port can support audio from either of (3) sources.
If the Input Video/Audio Source is HDMI, the audio can be extracted from the embedded signal.
If the Input Audio Source is connected to the external Audio Input, this same audio will be present on the Audio & ARC jack.
If ARC is selected, the audio will be from the destination device (ex: TV).
ToenabletheARCoptiononaspecicOutput,performthefollowingsteps:
- Press the ARC button.
- On the Destination row, Press 1 THRU 4 (the buttons will illuminate).
- Press the ENTER button. The new conguration will be stored.
The front panel LCD display will now show an “A“ under the Output port.
- Or press ARC again to cancel the operation.
TodisabletheARCoptiononaspecicOutput,performthefollowingsteps:
- Press the ARC button
- On the Destination row, press 1 THRU 4 (the buttons will illuminate).
- Press ENTER. The pre-set conguration will execute.
The front panel LCD display will be blank under the Output port.
- Or press ARC again to cancel the operation.
Note:
1. Operation will abort if no keys are pressed within 5 seconds.
2. The AUX Audio input only functions when a valid HDMI / DVI video signal is present. Without video, the AUX audio will not operate.

6
FRONT PANEL
FRONT PANEL
10. FUNCTION KEY - AUX (The audio additional on the “ Audio / ARC” Port ):
The AUX FUNCTION feature allows you to replace the embedded HDMI audio signal with an
audio signal that is connected to the switchers Audio AUX Input. Using the AUX function, this
replaces the audio and does not mix the audio. (Default = AUX Disabled)
ToenabletheAUXoptiononaspecicOutput,performthefollowingsteps:
- Press the AUX button.
- On the Source row, press 1 THRU 4 (the buttons will illuminate).
- Press ENTER. The new conguration will be stored.
The front panel LCD display will show an “X” under the Source port.
- Or press AUX again to cancel the operation.
TodisabletheAUXoptiononaspecicOutput,performthefollowingsteps:
- Press the AUX button.
- On the Source row, press 1 THRU 4 (the buttons will illuminate).
- Press ENTER. The pre-set conguration will execute.
The front panel LCD display will be blank under the Output port indicating the audio source is not embedded on the HDMI cable.
- Or press AUX again to cancel the operation.
Note:
1. Operation will abort if no keys are pressed within 5 seconds.
2. The AUX Audio input only functions when a valid HDMI / DVI video signal is present. Without video, the AUX audio will not operate.

7
FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - EDID:
Used to display change current EDID mode.
- Press EDID to select the new EDID mode or selection.
- Press Source row #1 or #2 to select EDID modes.
- Press ENTER to ready memory location.
- Or press EDID again to cancel the operation.
Operation completes.
Note: Operation will abort if no keys are pressed within 5 seconds.

8
FRONT PANEL
FRONT PANEL
13. FUNCTION KEY - ALL:
Disables (mutes) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by the OFF button. The display will show “0“ indicating all destinations
have no video selected.
Option 2
- Press ALL followed by Source 1 THRU 4. The display will show the Source selected.
- Press ENTER. The pre-set source selection will be assigned to all destinations.
14. FUNCTION KEY - OFF:
Disables (mutes) video to the selected channels or either destination.
- Press OFF button followed by any Destination channel.
- Press 1 THRU 4 output destinations. The display will show “0“ for the selected channel
indicating no video selected.
15. FUNCTION KEY - LOCK:
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
16. FUNCTION KEY - ENTER: Press ENTER to conrm entries.