Shinybow usa Sb-3879 User manual

INSTRUCTION MANUAL

MODEL : SB-3879

HDMI Video Scaler

7x2 (mirrored) Multi Format HDMI Video Scaler Selector Switch

7 In’s Converted to VGA & HDMI Output

HDTV Distribution Ampliﬁer Series

Thank you for purchasing the SB-3879 HDMI Video Scaler.You will ﬁnd this unit easy to install and highly reliable

but it is essential that you read this manual thoroughly before attempting to use this HDMI Video Scaler.

MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.

Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of ﬁre, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and

excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience

receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the

means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC

voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use

the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ﬂow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualiﬁed service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports ﬁrst, then remove the power cable; ﬁnally, disconnect the interconnecting cables to

other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,

use only the original factory packing.

19. Service Information Equipment should be serviced by qualiﬁer service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain

D. The equipment does not appear to operate normally, or exhibits a marked change in performance

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF AGENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of ﬁre,

electrical shock and injury to persons.

• To prevent ﬁre or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow

for sufﬁcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. We assume no responsibility for any

infringements of patents or other rights of third parties which may

result from its use.

We assume no responsibility for any inaccuracies that may be

contained in this document. We make no commitment to update or

to keep current the information contained in this document.

We reserve the right to make improvements to this document and/

or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed,stored in aretrievalsystem,or anyofitspart translated

into any language or computer ﬁle, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise — without express written permission and consent

Version 1.2 SEPT 2013

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may

be trademarks of the companies with which they are associated.

CONTENTS

INTRODUCTION ...............................................................1

FEATURES.........................................................................2

SPECIFICATIONS .............................................................3

FRONT PANEL .................................................................4

REAR PANEL ..................................................................5

REMOTE CONTROL ........................................................8

IR CODES .........................................................................9

IR EXTENDER .................................................................10

TYPICAL APPLICATION .................................................11

RESOLUTION SUPPORT ...............................................12

VIDEO TIMING LIST ......................................................16

OSD OPTIONS OVERVIEW ............................................20

LIMITED WARRANTY .................................................... 26

INTRODUCTION

Congratulations on your purchase of a professional high-

performancescalerandthankyouforyoursupportofShinybowUSA

products. The SB-3879 is a video graphics scaler that accepts

seven types of signals: analog video, S-Video, component video,

VGA, DVI, HDMI, and display port signals.

It scales the input signals into either VGA or HDMI signals,

supporting higher full HD resolutions of 480i/p, 720p, 1080i/p.

Designed to solve problems of compatibility between source

devices and monitors, it is also useful for delivering one single

image on a TV wall. In addition to the front panel buttons and the

IR remote control, users may gain control over the SB-3879 using

a PC through the RS-232 serial port or Ethernet port.

PACKAGE CONTENTS

Check that you have the following components;

• SB-3879 Video Scaler

• IR Remote Control

• Rack Mounts

• IR extender receiver

• RS-232 driver CD (All Windows Operating Systems)

• RS-232 cable

• Users Guide

• AC/DC Adapter: 12 VDC, 2A universal type switch 50/60Hz,

100~230 VAC

FEATURES

• Supports HDMI 1.4a 30 formals and suits HDMI V1.4 transmitter & receiver

• Compliant with HDMI 1.4, DVI 2.0, and HDCP 2.0

• Input support:

• Analog: analog video, S-Video, composite video, VGA

• Digital: DVI, HDMI and display port (2560x1600)

• Output support: VGA and HDMI 1080p with deep color 36-bit

• Output audio support: S/PDIF, stereo audio

• Advanced 30 de-interlace, smooth edge algorithm and 3:2/2:2 ﬁlm mode processing

• 3D format functions: frame packing, side-by-side, top/bottom adjustment

• Bypasses XGA & 720p 120Hz 3D signal for DLP link 3D ready projector for active 3D display

• Supports full HD @24Hz, full HD 3D signal, with special algorithm for RH/LH synchronization

• Supports wide range of HD resolutions ranging from XGA to WUXGA1920x1200 to

• HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p

• Compatible with all HDMI source devices, PC monitors, plasma HD display, HDTV and audio receivers/ampliﬁers

• Supports intelligent color adjustment (discrete RGB color adjustment, hue, saturation, sharpness, contrast, brightness, and preset

color modes)

• Rack mountable: 19-inch ear rack mount

• Various user interface control:

• Windows-based GUI control via RS-232 port

• Front panel push buttons, IR wireless remote control,Third party RS-232 controller (via simple ASCII), Ethernet

• Supports IR extender with maximum extend distance reaching 1000 feet / 300 meters

• Supports TV wall function, allowing the image to be divided on multiple displays/monitors

• Power supply DC 12V, universal type switch, 100-240 VAC, 50/50Hz

SPECIFICATIONS

Scaler Type: 7 in 2 out HDMI Video Scaler

Video Input Signal: 1x Composite / 1x S-Video /1x Component / 1x VGA / 1x DVI / 1x HDMI / 1x DP

Audio Input Signal: Digital Audio (PCM), Stereo Audio

Video Output Signal: 1x RGB, 1x HDMI

Audio Output Signal: 1x S/PDIF Digital Audio, 1xAnalog, Audio RH/LH, 1x HDMIAudio

3D Support: 3D Video Format in HDMI 1.4a (225MHz)

Input Resolution: Up to 1080p-60, 1920x1200, and DP 2560x1600

Output Resolution: Up to 1080p-60 and 1920x1200

Source Status: Automatic scanning of input/output status

HDCP Support: DVI/ HDMI/ Display Port, compliant with HDCP 2.0

HDMI Compliance: HDMI 1.4a receiver and transmitter

HDMI Cable Distance: Max. ~ 50 feet (15 meters), depending on cable quality

Infrared Frequency: 38KHz

Chassis Material: Metal

IR Extend Distance: ~1000 feet (300 meters) line cable via IR extender

Control: IR remote control, RS-232, front panel push buttons

Dimensions: 11.96 x 5.90 x 1.73 in (304x150x11mm)

Rack Mount: 19-inch panel type (1U-44L)

Power Supply: Input 100 ~ 240 VAC, 50/60 Hz / Output DC 12V, 3A

Safety Approvals: CE, FCC, RoHS (2002/95/EC)

Temperature: 32 ° F ~ 100 ° F (0 ° ~32 ° C)

Shipping Weight: 2.05 Kgs / 3.42 lbs

Video Wall:

• Magnify, scroll, pan through all inputs

• Video wall function: Image split, cropping, and assign display location

• Pixel based overlap adjustment in all edges, up to 15x15 matrix displays

• Up to 2560x1600 input resolution via display port

System Control:

• Box ID for easy independent control through IR, RS-232, and 5 selectable proﬁle settings for difference display

• Ethernet control module with RJ45 connector

• Code update through RS-232

• ASCII control protocol over RS-232 and Ethernet

• One DC 12V/1Atrigger output

Advanced Video Processing:

• Advanced 3D de-interlace, smooth edge algorithm and 3:2/2:2 ﬁlm mode

• High quality video and graphics scaling up and down

• Frame rate conversion

Intelligent Color Adjustment:

• Discrete RGB, color adjustment, hue, saturation, sharpness, contrast, brightness, 4 preset color modes

3D Function:

• Auto detect standard 3D signal (with 3D index inside) from Blu-ray DVD or STB

• Supports full HD @ 24 Hz full HD 3D signal with special algorithm for RH/LH synchronization

• Bypass XGA& 720p 120 Hz 3D signal for DLP link

• 3D ready projector for active 3D display

As product improvements are continuous, speciﬁcations are subject to change without notice.

FRONT PANEL

1. POWER ON SWITCH

The power switch turns the unit on and off.The LED will illuminate blue 10 indicate the switcher is ON and receiving power. The scaler will

remember the last setting during a power cycle. When turned on again, it will automatically apply the setting last used.

2. MENU

Press menu to open the On-Screen Display interface. Press again to exit menu

3. ENTER

Press enter to conﬁrm your entries.

4. ARROW KEYS

Use the arrow keys to move between the On-Screen Display options. Press the up key to enter the upper layer and the down key to enter

the next layer. Press the left and right keys to select options in the same layer or change the value of a parameter.

5. IR SENSOR

The IR sensor receives IR commands from the supplied remote controller or a third party IR remitter.

6. OUTPUT SELECT BUTTONS

Select the desired resolution supported by your display devices. Press OTHERS for resolutions other than XGA, WXGA, 720p, 1080p.

The button will illuminate blue to indicate it is selected. Advanced resolution adjustment can be found in the OSD options.

7. INPUT SELECT BUTTONS

Select from one of the 7 buttons the video signal you intend to be scaled. The button will illuminate blue to indicate it is selected.

REAR PANEL

1. DC POWER INLET

The scaler suits a DC power plug-pack input connector. Please ensure

the plug-pack used is of an approved type and of correct current, voltage

output, and connector polarity. DV 12 Volt, power supply 2A.

2. ETHERNET CONNECTION

Connect a CATS cable to the Ethernet port for control of the scaler from

a computer.

3. RS-232 CONNECTION

Connect a serial cable to the RS-232 port for control at the scaler from a

computer.

4. LINK

Connect the link port for ﬁrmware updates. Used for testing purpose.

5. IR EXTENDER CONTROL

Supports remote control via IR extender. Maximum extend distance

reaches 1000 feet (300 meters).

Power Jack:

DC Jack - Inner OD O 2.1mm (+ )

Outside OD O 5.5mm (GND)

Power input - 12VDC, 2A

SPSC / RJ 45 connector

D-SUB 9-pin female connector

Terminal block connector

IR Extender Jack:

Female Jack - inner OD 0 3.5 mm

REAR PANEL

6. YPBPR + AR / ALAUDIO INPUT

Connect a signal of component video directly to the female RCA

connector, which supports component video (YPBPR) to HDTV

display devices. Connect the output port of your source audio

device to the AR/AL inputs.

7. VGA + VGA AUDIO INPUT

Connect a signal of VGA (RGBHV) to the HD-15F female connector.

Connect the output port of your source audio device to the audio input.

8. DVI + DVI AUDIO INPUT

Connect a signal of DVI to the digital video connector. Connect the

output port of your source audio device to the audio input.

9. HDMI INPUT

Connect 8 signal link of HDMI direct digital video/audio to the HDMI

connector, which supports HDMI digital video/audio and DVI digital

video sources.

10. DISPLAY PORT INPUT

Connect a signal of display port to the DP port, which supports digital

video and audio.

Component video via 3x RCAs

Female RCA connectors

Stereo audio via 2x RCAs

Female RCA connectors

VGA video jack

Female HD-15F connector

Female DVI connector

HDMI female jack

Display port digital video and audio

connector

REAR PANEL

11. VIDEO + AR I AL AUDIO INPUT

Connect a signal of composite video to the RCA connector.

Connect the output port of your source audio device to the

AR/AL inputs.

12. S-VIDEO + AR / AL AUDIO INPUT

Connect a signal input of S-Video to the connector. Connect the

output port of your source audio device to the AR/AL inputs.

13. SPDIF

Connect for digital audio output.

14. VGA OUTPUT

Connect a signal source of VGA(RGBHV) to the VGA connector.

15. HDMI OUTPUT

Connect a signal link of HDMI direct digital video/audio to this

Female HDMI connector, which supports HDMI digital video/audio

and DVI digital video sources.

Female RCA connector Stereo Audio

(AR/AL) Via 1x 03.5mm ear phone jack

connector

Note: With 1x female phone jack each

channel

Mini-DIN connector Stereo Audio (AR/

AL) Via 1x 03.5mm ear phone jack

connector

Note: With 1x female phone jack each

channel

Female RCA connector

Component Video (YPBPR) Via 3x

RCAs

Note: With 3x RCA female connectors.

HDMI digital video/audio connector

HDMI female connector

Note: With proper adapters, the scaler

can be used with DVI digital video

signals, and HDCP compliant.

REMOTE CONTROL

Before making any connections to the SB-3879. Observe the following:

Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%)

Ensure that the power switch is OFF

Ensure that all system grounds (earth) are connected to a common point.

Avoid powering equipment within a system from multiple power sources that may be separated by large distances

Connect all audio video sources and destination equipment

Power up all source and destination audio-visual sources

For each destination output select the appropriate input source by using The front panel input select buttons. The supplied IR remote

control. Or through the RS-232 serial communications port.

Upon power up the switcher will return to its last used setting before Powered down.

REMOTE CONTROL

For guidance on the OSD options, please refer to the OSD

instruction manual.

IR REMOTE CONTROL KEY :

1/2. POWER ON AND OFF: Turns on or off the scaler

3. MUTE: Stops playing sounds

4. SOURCE (HDMI, VGA, DVI, DP, YPBPR, VIDEO, S-VIDEO):

Selects your input signal type

5. ENTER: Conﬁrms your selection/enter the next layer of OSD options

6. ARROW KEYS: move up, down, left or right between the OSD

options. Use left and right keys to adjust the value of a parameter. Use

down key to enter the next layer of options and up key to move back.

7. RETURN: Return to the upper layer of OSD options

8. MENU: Opens up the OSD menu

9. INFO: Checks the connection status of input/output/ RS-232/Ethernet

ports

10. EXIT: Leaves the OSD menu

11. OUTPUT (XGA, WXGA, 720P, 1080P, OTHERS): Selects the

desired output resolution supported by your display device.

12. OSD TIME OUT: Adjusts the OSD menu display time

13. VIDEO WALL: Opens the video wall options

IR CODES

IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)

HOW TO SETUP IR CODES:

CUSTOM CODE: 20DF

POWER ON: 20DF 5DA2

POWER OFF: 20DF 5EA1

Mute: 20DF 02FD

HDMI: 20DF 1FEO

VGA: 20DF OAF5

DVI: 20DF 50AF

DP: 20DF 59A6

YPBPR: 20DF 58A7

VIDEO: 20DF 5AA5

S-VIDEO: 20DF 5BA4

RETURN: 20DF 11EE

MENU: 20DF 19EA

INFO: 20DF 1BE4

EXIT: 20DF 5CA3

ENTER: 20DF 51AE

UP: 20DF 44BB

RIGHT: 20DF 48B7

LEFT: 20DF 1CE3

DOWN: 20DF 1DE2

XGA: 20DF 07F8

WXGA: 20DF 4BB4

720p: 20DF 05FA

1080p: 20DF 06F9

OTHERS: 20DF 03FC

OSD TIME OUT: 20DF 15EA

VIDEO WALL: 20DF 15EB

Example 1: Select input VGA and output HDMI

The IR Data Code: 20DF OAF5 20DF 07F8

Example 2: Open OSD-> move right -> move down to next layer -> enter to conﬁrm selection

The IR Data Code: 20DF 15EA 20DF 48B7 20DF 1DE2 20DF 51AE

IR EXTENDER

REAR PANEL IR EXTENDER PORTS

••• When you plug the externallR extender into the scaler, the front panel IR receiver remains active . •••

IR EXTENDER PACKAGE :

HOW TO SETUP THE IR EXTENDER COMPONENTS

TYPICALAPPLICATION

7 IN 2 OUT HDMI VIDEO SCALER

INSTALLING

CONTROL PORTS :

1. Front Panel - Function Key Press Buttons

2. IR Remote - IR Remote Controller

3. RS-232 Interface - RS-232 Interface System

4. Ethernet - Ethernet Interface System

INPUTS 1 ~ 7 PORT SOURCE SIGNALS : COMPONENT VIDEO,AV, DVI, HDMI, Display Port (5 input ports connected)

OUTPUTS 1 ~ 2 PORT DISPLAY SIGNALS : VGA, HDMI

SB-3879 SUPPORTS 7x INPUTSAND 2x OUTPUTS, CONTROL IR & RS-232 INTERFACE SYSTEM PORTS.

INPUT RESOLUTION SUPPORT

Resolution INPUT

COMPONENT VGA DVI HDMI Display Port

640x350 @ 85 Hz 480p / 480i 

640x400 @ 85 Hz 576p / 576i 

640x480 @ 60 Hz 720p 

640x480 @ 72 Hz VGA 

640x480 @ 75 Hz VGA  

720x400 @ 70 Hz DOS  

720x400 @ 85 Hz 1080p / 1080i 

800x600 @ 56 Hz SVGA 

800x600 @ 60 Hz SVGA  

800x600 @ 72 Hz SVGA  

800x600 @ 75 Hz SVGA  

832x624 @ 75 Hz SVGA  

848x480 @ 59 Hz WVGA  

848x480 @ 60 Hz WVGA  

852x480 @ 60 Hz 480p 

1024x768 @ 60 Hz XGA  

1024x768 @ 70 Hz XGA 

1024x768 @ 75 Hz XGA 

1152x864 @ 75 Hz XGA+  

1280x720 @ 48 Hz HD 720 

1280x720 @ 50 Hz HD 720  

1280x720 @ 60 Hz HD 720  

1280x768 @ 60 Hz WXGA  

1280x768 @ 75 Hz WXGA  

1280x768 @ 60 RB WXGA 

1280x800 @ 60 Hz WXGA 

1280x800 @ 75 Hz WXGA 

INPUT RESOLUTION SUPPORT

Resolution INPUT

COMPONENT VGA DVI HDMI Display Port

1280x960 @ 60 Hz SXGA 

1280x1024 @ 60 Hz SXGA  

1280x1024 @ 75 Hz SXGA  

1360x768 @ 60 Hz SXGA  

1360x768 @ 75 Hz SXGA 

1366x768 @ 60 Hz WXGA 

1400x788 @ 60 Hz WXGA+ 

1400x1050 @ 60 Hz SXGA+  

1400x1050 @ 75 Hz SXGA+  

1400x1050 @ 60 RB SXGA+ 

1440x900 @ 60 Hz WXGA+ 

1440x900 @ 75 Hz WXGA+ 

1440x1050 @ 60 Hz SXGA+  

1600x1200 @ 60 Hz UXGA  

1600x1200 @ 65 Hz UXGA 

1600x1200 @ 70 Hz UXGA 

1600x1200 @ 75 Hz UXGA 

1680x1050 @ 60 Hz WSXGA+  

1792x1344 @ 60 Hz 

1856x1392 @ 60 Hz 

1920x1200 @ 60 RB WUXGA 

1920x1200 @ 60 Hz WUXGA 

1920x1440 @ 60 Hz WUXGA 

1920x1440 @ 75 Hz WUXGA 

720x480p @ 59 Hz DVD “NTSC” 

720x480p @ 59 PW DVD “NTSC” 

720x576p @ 50 Hz DVD “PAL” 

INPUT RESOLUTION SUPPORT

Resolution INPUT

COMPONENT VGA DVI HDMI Display Port

720x576p @ 50 PW DVD “PAL” 

1280x720p @ 50 Hz HDTV 720p 

1280x720p @ 60 Hz HDTV 720p  

1280x720p @ 100 Hz HDTV 720p 

1280x720p @ 120 Hz HDTV 720p 

1920x1080p @ 24 Hz 1080p HD 

1920x1080p @ 30 Hz 1080i HD 

1920x1080p @ 50 Hz 1080p HD 

1920x1080p @ 60 Hz 1080p HD  

1920x1080p @ 24 Hz Full HD 1080p 

2048x1280 @ 60 Hz 

2560x1600 WQXGA 

OUTPUT RESOLUTION SUPPORT

Front Panel Buttons Resolution OUTPUT

VGA HDMI

OTHERS

720x480 

800x600 

1280x800 

1280x1024 

1360x768 

1400x1050 

XGA 1600x1200 

WXGA 1920x1200 

720p 1024x768 

1080p 1280x720 

1080p 1920x1080 

Note: When the front panel button OTHERS is pressed, the scaler will automatically apply the resolution 1360x768. Users may continue

pressing OTHERS to cycle through the following four resolutions: 1360x768 -> 1280x1024 -> 1600x1200 -> 1920x1200

To select 720x480, 800x600, 1280x800, open the OSD menu and go to the IMAGE PROPERTIES to adjust the settings in the output

mode.

VIDEO TIMING LIST (HDMI)

Resolution H

Freq.

(Khz)

Freq.

(Hz)

Pixel

Clock

(MHz)

Total

Pixel

Display

Pixel

Front

Porch

Sync

Width

Sync

Pol

Total

Lines

Display

Lines

Front

Porch

Sync

Width

Sync

Pol

640x480 @ 60 Hz 31.484 59.97 25.1875 800 640 16 96 N 525 480 10 2 N

640x480 @ 72 Hz 37.861 72.809 31.5 832 640 24 40 N 520 480 9 3 N

640x480 @ 75 Hz 37.5 75 31.5 840 640 16 64 N 500 480 1 3 N

720x400 @ 70 Hz 31.458 70.063 28.3125 900 720 16 108 N 449 400 13 2 P

800x600 @ 56 Hz 35.156 56.25 36 1024 800 24 72 P 625 600 1 2 P

800x600 @ 60 Hz 37.879 60.317 40 1056 800 40 128 P 628 600 1 4 P

800x600 @ 72 Hz 48.077 72.188 50 1040 800 56 120 P 666 600 37 6 P

800x600 @ 75 Hz 46.875 75 49.5 1056 800 16 80 P 625 600 1 3 P

848x480 @ 59 Hz 29.83 59.659 31.5 1056 848 24 80 N 500 480 3 5 P

848x480 @ 60 Hz 31.02 60 33.75 1088 848 16 112 P 517 480 6 8 P

1024x768 @ 60 Hz 48.363 60.004 65 1344 1024 24 136 N 806 768 3 6 N

1024x768 @ 70 Hz 56.476 70.069 75 1328 1024 24 136 N 806 768 3 6 N

1024x768 @ 75 Hz 60.023 75.029 78.75 1312 1024 16 96 P 800 768 1 3 P

1152x864 @ 75 Hz 67.5 75 108 1600 1152 64 128 P 900 864 1 3 P

1280x720 @ 48 Hz 35.539 47.961 58 1632 1280 48 128 N 741 720 1 3 P

1280x720 @ 50 Hz 36.918 49.822 60.25 1632 1280 48 128 N 741 720 1 3 P

1280x720 @ 60 Hz 44.621 59.814 74.25 1664 1280 56 136 N 746 720 1 3 P

1280x768 @ 60 Hz 47.396 59.995 68.25 1440 1280 48 32 P 790 768 3 7 N

1280x768 @ 60 Hz 47.776 59.87 79.5 1664 1280 64 128 N 798 768 3 7 P

1280x768 @ 75 Hz 60.289 74.893 102.25 1696 1280 80 128 N 805 768 3 7 P

1280x800 @ 60 Hz 49.702 59.81 83.5 1680 1280 72 128 N 831 800 3 6 P

1280x800 @ 75 Hz 62.795 74.934 106.5 1696 1280 80 128 N 838 800 3 6 P

1280x960 @ 60 Hz 60 60 108 1800 1280 96 112 P 1000 960 1 3 P

1280x1024 @ 60 Hz 63.981 60.02 108 1688 1280 48 112 P 1066 1024 1 3 P

1280x1024 @ 75 Hz 79.976 75.025 135 1688 1280 16 144 P 1066 1024 1 3 P

1360x768 @ 60 Hz 47.712 60.015 85.5 1792 1360 64 112 P 795 768 3 6 P

1366x768 @ 60 Hz 48 60 72 1500 1366 14 56 P 800 768 1 3 P

1400x1050 @ 60 Hz 64.744 59.948 101 1560 1400 48 32 P 1080 1050 3 4 N

1400x1050 @ 60 RB 65.317 59.978 121.75 1864 1400 88 144 N 1089 1050 3 4 P

1400x1050 @ 75 Hz 82.278 74.867 156 1896 1400 104 144 N 1099 1050 3 4 P

1440x900 @ 60 Hz 55.935 59.887 106.5 1904 1440 80 152 N 934 900 3 6 P

1440x900 @ 75 Hz 70.506 74.847 136.5 1936 1440 96 152 N 942 900 3 6 P

1440x1050 @ 60 Hz 65.234 59.903 125.25 1920 1440 88 152 N 1089 1050 3 10 N

1600x1200 @ 60 Hz 75 60 162 2160 1600 64 192 P 1250 1200 1 3 P

1680x1050 @ 60 Hz 65.402 60.057 146.5 2240 1680 104 176 N 1089 1020 3 6 P

1920x1200 @ 60 RB 74.038 59.95 154 2080 1920 48 32 P 1235 1200 3 6 N

720x480p @ 59 Hz 31.469 59.94 27 858 720 16 62 N 525 480 9 6 N

720x480p @ 59 PW 31.469 59.94 27 858 720 16 62 N 525 480 9 6 N

720x576p @ 50 Hz 31.25 50 27 864 720 12 64 N 625 576 5 5 N

720x576p @ 50 PW 31.25 50 27 864 720 12 64 N 625 576 5 5 N

1280x720p @ 50 Hz 37.5 50 74.25 1980 1280 440 40 P 750 720 5 5 P

1280x720p @ 60 Hz 45 60 74.25 1650 1280 110 40 P 750 720 5 5 P

1280x720p @ 100 Hz 75 100 148.5 1980 1280 440 40 P 750 720 5 5 P

1280x720p @ 120 Hz 90 120 148.5 1650 1280 110 40 P 750 720 5 5 P

1920x108p @ 24 Hz 27 24 74.25 2750 1920 638 44 P 1125 1080 4 5 P

1920x108p @ 30 Hz 33.75 30 74.25 2200 1920 88 44 P 1125 1080 4 5 P

1920x108p @ 50 Hz 56.25 50 148.5 2640 1920 528 44 P 1125 1080 4 5 P

1920x108p @ 60 Hz 67.5 60 148.5 2200 1920 88 44 P 1125 1080 4 5 P

VIDEO TIMING LIST (VGA)

Resolution H

Freq.

(Khz)

Freq.

(Hz)

Pixel

Clock

(MHz)

Total

Pixel

Display

Pixel

Front

Porch

Sync

Width

Sync

Pol

Total

Lines

Display

Lines

Front

Porch

Sync

Width

Sync

Pol

640x480 @ 60 Hz 31.563 60.119 25.1875 800 640 16 96 N 525 480 10 2 N

640x480 @ 72 Hz 37.861 72.809 31.5 832 640 24 40 N 520 480 9 3 N

640x480 @ 75 Hz 37.5 75 31.5 840 640 16 64 N 500 480 1 3 N

720x400 @ 70 Hz 31.528 70.218 28.3125 900 720 16 108 N 449 400 13 2 P

800x600 @ 56 Hz 35.156 56.25 36 1024 800 24 72 N 625 600 1 2 P

800x600 @ 60 Hz 37.879 60.317 40 1056 800 40 128 N 628 600 1 4 P

800x600 @ 72 Hz 48.077 72.188 50 1040 800 56 120 N 666 600 37 6 P

800x600 @ 75 Hz 46.875 75 49.5 1056 800 16 80 P 625 600 1 3 P

848x480 @ 59 Hz 29.83 59.659 31.5 1056 848 24 80 N 500 480 3 5 P

848x480 @ 60 Hz 31.02 60 33.75 1088 848 16 112 P 517 480 6 8 P

1024x768 @ 60 Hz 48.363 60.004 65 1344 1024 24 136 N 806 768 3 6 N

1024x768 @ 70 Hz 56.476 70.069 75 1328 1024 24 136 N 806 768 3 6 N

1024x768 @ 75 Hz 60.023 75.029 78.75 1312 1024 16 96 N 800 768 1 3 P

1152x864 @ 75 Hz 67.5 75 108 1600 1152 64 128 P 900 864 1 3 P

1280x720 @ 48 Hz 35.539 47.961 58 1632 1280 48 128 N 741 720 1 3 P

1280x768 @ 60 RB 47.396 59.995 68.25 1440 1280 48 32 P 790 768 3 7 N