Shinybow USA SB-3877 User manual

SAFETY INFORMATION
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL PAGE 11
SB-3877 INSTRUCTION & OPERATION MANUAL
SPECIFICATIONS
VIDEO/AUDIO INPUTS 8x VIDEO INPUTS
- 2x HDMI (Digital Video-TMDS & Digital Audio-PCM) via HDMI connectors
- 2x CVBS/S-Video(Y/C)/Audio Via Composite(1x RCA), S-Video(1x min din-4p) & Stereo Audio(2xRCA)
- 2x Component Video(YP P )/Audio Via Component(3x RCA) & Stereo Audio(2xRCA)BR
- 2x VGA(RGBHV) / Audio Via VGA(2x HD-15P) & Stereo Audio(2xRCA)
VIDEO/AUDIO OUTPUTS 2x VIDEO OUTPUTS
- 2x HDMI (Digital Video-TMDS & Digital Audio-PCM) via HDMI connectors
- 2x Digital Audio Via 2x RCA
- 2x VGA(RGBHV) / Audio Via VGA(2x HD-15P) & Stereo Audio(2xRCA)
AUTO DETECTION TV VIDEO SYSTEM
NTSC-M 3.58, NTSC-J, 4.43, PAL-B-D-I-G-H-K, PAL-M, PAL-N, PAL-N COMB-N, SECAM (Impedance:75 ohms)
SAFETY APPROVALS CE, FCC, RoHS(2002/95/EC)
DIMENSIONS (LWH) 19 x 7.87 x 1.75 (482mm x 200mm x 44mm)”””
POWER SUPPLY 12VDC, 3A (2.45A Max.) Universal Switch type 50/60Hz 100~230 VAC
OSD MENU SELECTIONS Adjust Color : Contrast, Brightness, Sharpness, Level and Gain
VIDEO BANDWIDTH 250MHz, (-3 d B)
AUDIO BANDWIDTH >60MHz, (-3 d B)
AUDIO FREQUENCY RESPOND 20Hz ~ 20KHz
INPUT SOURCE RESOLUTIONS
SHIPPING WEIGHT 3.5KGS
CONTROL Direct Front Panel menu, Remote control & RS-232/RS-485
- HDMI for 480p, 720p & 1080p
- Component Video (YP P ) for 480p, 720p & 1080pBR
- VGA for VGA(640x480), SVGA(800x600), XGA(1024x768), SXGA(1280x1024) Maximum
RS-232 CONTROL 9600 bps, No Parity, 8 bits, 1 Stop bit
UNIT OUTPUT RESOLUTIONS
- HDMI for 720p & 1080p
- VGA for SVGA (800x600), XGA (1024x768), SXGA (1280x1024), WXGA (1366x768)
WXGA+ (1680x1050), WUXGA (1920x1200) Maximum
1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original
factory packing.
2. Read all documentation before operating your equipment. Retain all documentation for future reference.
3. Follow all instructions printed on unit chassis for proper operation.
4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
5. Make sure power outlets conform to the power requirements listed on the back of the unit.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of
a piece of equipment is not defeated.
8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by
any warranty.
9.
Power down & disconnect unit from mains voltage before making connections.
10. Never hold a power switch in the “ON position.＂
11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.
12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal of air around the unit,
flow
13.
such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be
periodically “blown free” of foreign matter.
14.
Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.
15.
Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
16.
Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.
Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
from the appliance.
As product improvements are continuous, specifications are subject to change and
without notice.
www.shinybowusa.com

PAGE 3
SB-3877 INSTRUCTION & OPERATION MANUAL
INTRODUCTION AND TABLE OF CONTENTS
3
IR EXTENDER
4
5
6
7
This symbol is intended to alert the user to the presence of uninsulated
enclosure tha may be of sufficientmagnitude to constitue a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important
operational and maintenance (serving) instructions in the literature
accompanying the appliance.
T prevent electric shock do not use this (polarised) plug with ano
extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
T prevent electric shock, match wide blade of plug to wide slot,o
fully insert.
Caution:
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
T
I
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. .
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FRONT PANEL
REAR PANEL
REMOTE CONTROL
INTRODUCTION
of uninsulated “dangerous voltage” within the products enclosure that
RS-232 & RS-485 SERIAL INTERFACE 8
RS-232 SERIAL COMMANDS 9
INSTALLATIONS 10
SPECIFICATIONS 11
INSTALLATIONS
PAGE 10 SB-3877 INSTALLATION & OPERATION MANUAL
INSTALLING
INPUT
OUTPUT
DVD
DVD
AV Player x2
DVDDVD
DVDDVD
VGA Player x2
INPUT
INPUT
INPUT
DVD
DVD DVD
YUV Player x2
INPUT
RS PC232 RS485 PC
INPUT
INPUT
DVD
DVD
SV Player x2
DVD
DVD
HDMI Player x2
INPUT
INPUT
INPUT
INPUT
OUTPUT
Audio in
OUTPUT
Audio in
Audio in
HDTV
VGA in
Audio in
Audio in
HDMI in
Audio in
Audio in
HDMI in
Audio in
Audio in
Audio in
INPUTS PORT SIGNALS :
VGA in
Projector
VGA in
VGA in
HDMI in
HDMI in
ROOM-1
ROOM-2
ROOM-3
ROOM-4
HDTV
HDTV
1. HDMI - HDMI connector with fix screw
2. HDMI - HDMI connector with fix screw
3. S-VIDEO / Audio or COMPOSITE VIDEO / Audio
Unit output select via which one is the last input source.
4. S-VIDEO / Audio or COMPOSITE VIDEO / Audio
Unit output select via which one is the last input source.
5. COMPONENT VIDEO(YP P ) / Audio
BR
Component Video input via HD resolutions 480p, 720p and 1080p
6. COMPONENT VIDEO(YP P ) / Audio
BR
Component Video input via HD resolutions 480p, 720p and 1080p
7. VGA / Audio
VGA input resolution compatible XGA, SXGA(1280x1024) Max.
8. VGA / Audio
VGA input resolution compatible XGA, SXGA(1280x1024) Max.
OUTPUT PORT SIGNALS :
1. HDMI - HDMI output with digital video and digital audio
Digital Audio - Digital Audio(PCM) from HDMI input sources
VGA / Audio - output resolution Scaling to WUXGA(1920x1200)
2. HDMI - HDMI output with digital video and digital audio
Digital Audio - Digital Audio(PCM) from HDMI input sources
VGA / Audio - output resolution Scaling to WUXGA(1920x1200)
SB-3877 SUPPORT TWO HDMI -VGA - DIGITAL MATRIX OUTPUTS
SUPPORT TWO IR & IR EXTENDER PORTS.
The -3877 is a 8:2 Multi-Video Matrix Switcher
featuring 8 inputs and pre-emphasized 2 outputs.
> 8 inputs as following :
2 x Composite Video/S-Video+Audio,
2 x Component Video+Audio,
2 x VGA+Audio,
2 x HDMI
> 2 matrix outputs as following :
2 x VGA+Audio
2 x Digital Audio
2 x HDMI
Automatic input TV standard system detection :
> NTSC 3.58 / NTSC-EIAJ / NTSC 4.43
> PAL / PALM / PAL-N / PAL-COMB-N/PAL-60
> SECAM
This switcher supporst full data rates and enabling
input HDMI 480p, 720p or 1080i/p formats. PC
resolution (1920 x 1200HD) is ideally suitable for
high Definition LCD Television, HDTV, Plasma
display or Monitor applications.
Control is provided via Front panel buttons with LED
readout, IR remote control, or RS-232..
An RS-232 interface is provided for interfacing with
a third party controller.

PAGE 4 SB-3877 INSTRUCTION & OPERATION MANUAL
FRONT PANEL
1
FRONT PANEL
2
POWER
12
RESOLUTION
SET / OSD
SB-3877
3 4 5 6 7 8
SELECT
Audio Value
2
1
8
2
1
Aud io Value
OUT
1
OUT
2
RS 485
MATRIX
2
SWITCHER
MULTIVIDEO
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1 VGA-2
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1
YP P -2
BR VGA-2
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1 VGA-2
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1
YP P -2
BR VGA-2
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1
YP P -2
BR VGA-2
HDMI-1 HDMI-2 CVSV-1 CVSV-2 YPP-1
BR VGA-1
YP P -2
BR VGA-2
XGA SXGA
WXGA
WSXGA+
WUXGA
1
2
1
2
SVGA
720p 1080p
VGA HDMI
800-600 1024-768 1280-1024 1366-768 1680-1050 1920-1200
TM
HIGH-DEFINITIONMULTIMEDIAINTERFACE
ENTER
3 3
43 53 63
83 93
10 3
11
3
7
PAGE 9
SB-3877 INSTRUCTION & OPERATION MANUAL
RS-232 SERIAL COMMANDS
FRONT PANEL LOCK
Note : Hard resetting the unit will unlock the Front Panel controls.
SBSYSMLK - When front panel is locked, changes can only be
made by Rs232
SBSYSMUK - Front Panel Unlock
Unit will respond with
SBSYSLOK
- Front Panel has been Locked
SBSYSULK - Front Panel has been Unlocked
Example : Lock Front Panel Buttons
SBSYSMLK -Send
SBSYSLOK -Rcvd
UNIT RESET
SBSYSMLK - Reset every output to Input 1
Unit will respond with
SBRSTACK - Unit has reset each Output to Input 1
Example : Reset all outputs to Input 1
SBALLRST
-Send
SBRSTACK -Rcvd
Power Off mode.
- Put system into Standby (Soft Power Off)
- Bring unit out of Standby (Soft Power On)
Unit will respond with
- Unit is in Standby
SBALONAK - Unit is no longer in Standby
Example : Put Unit in Standby (Soft Power)
SBSYSMOF -Send
SBALOFAK -Rcvd
SBALOFAK
SBSYSMOF
SBSYSMON
STANDBY MODE
Note: Turning the unit System Power Off over RS232 will blank
the displays leaving only the Power Switch LED on. Hard
resetting the unit when in System Power Off mode will return the
unit to normal operation and unlock the front panel.
Even while the unit is turned off by RS232 it will continue to accept and act
upon switching commands. This allows you to set up a scene before soft｀＇
powering on the unit and enabling the video outputs. The unit will still return
status and change messages in response to commands sent while in System
POWER ON SWITCH
SOURCE SELECT BUTTONS
OSD / SET SETUP BUTTONS
1
3
The power switch turns the unit on and off.
The LED will illuminate red to indicate
that the switcher is ON and is receiving power
INPUT SOURCES DISPLAY
2
Input sources 1 to 8 LED illuminates green to
indicate that a video source is present on that input.
A separate output-1 and 2 source select buttons
are provided for each destination.
Select sources are 1-HDMI, 2-HDMI, 3-CV/SV
4-CVSV, 5-YP P
BR , 6-YP P , 7-VGA, 8-VGA BR
HDMI & VGA RESOLUTION DISPLAY
RESOLUTION SELECT BUTTONS
4
6
5
To select output resolution per channel.
Output of HDMI & VGA resolution via LED display.
VGA : SVGA(800x600), XGA(1024x768), SXGA
(1280x1024), WXGA(1366x768), WSXGA+
(1680x1050), WUXGA(1920x1200)
HDMI : 720P / 1080P
SET : Setup button resolution selections.
IR SENSOR
7
The IR sensor receives IR commands from the
supplied remote controller.
RS 485 LED DISPLAY
8
RS 485 LED illuminates when an active
RS 485 connection is used.
OUTPUT AUDIO-1 ADJUST
10
Adjust output-1 Audio Value via LED display.
OSD CONTROL
9
Adjust OSD on display via separate two output
screens.
OUTPUT AUDIO-2 ADJUST
11
OSD: On Screen Display selections.
4
Adjust output-2 Audio Value via LED display.

PAGE 5
SB-3877 INSTRUCTION & OPERATION MANUAL
1
OUTPUT
7
8
Audio
INPUT 7 - 8
INPUT
DC 12V
RoHS/95/EC
DIGITAL
DIGITAL
HDMI AUDIO
AUDIO
VGA
VGA
1
2
5
6
AR
INPUT 5 - 6
12
3
4
INPUT 3 - 4
1
2
INPUT 1 - 2
AL YPBPBPRPRAR AL VIDEO
S-VIDEO
IR EXT.
RS-485
RS-232
TM
HIGH-DEFINITIONMULTIMEDIA INTERFACE
TM
TM
REAR PANEL
REAR PANEL
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PAGE 8 SB-3877 INSTRUCTION & OPERATION MANUAL
RS-232 & RS-485 SERIAL INTERFACE
RS232
The Shinybow switcher can be controlled via the RS-232
serial control port to allow for interfacing to a PC,
The serial communication parameters are 9600 baud, 8 bit,
No Parity and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognises a complete command it will perform
the requested action - there is no delimiter character required.
The unit does not send out a message when a value is changed
from the front panel or by IR control. If the unit needs to be
controlled via the front panel in addition to the RS232 control, you should
regularly poll the unit status to ensure the control system
accurately reflectes the current settings.
COMMANDS
To Switch Inputs to Outputs
- Where X is Output Number (1-8) and Y is
Number (1-2)
Unit will respond with
SBUD0XOY - Where X is Output Number (1-2) and Y is
Input Number (1-8)
Example : Send Input 7 to Output 2
-Send
SBUD07O2 -Rcvd
or similar third party control system.
SBI07O02
SBI0XO0Y
RS-232 & RS-485 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM
15
69
RS-232 SERIAL INTERFACE
Pin RS-232 Definition
1 ------ Not used
2 TX Transmitter
3 RX Receiver
4 ------ Not used
5 GND Ground
6 ------ Not used
7 ------ Not used
8 ------ Not used
9 ------ Not used
Pin RS-485 Definition
1 ------ Not used
2 A non-inverting
3 B inverting
4 ------ Not used
5 GND Ground
6 ------ Not used
7 ------ Not used
8 ------ Not used
9 ------ Not used
RS-485 SERIAL INTERFACE
DIGITAL AUDIO OUTPUTS
STEREO AUDIO OUTPUTS
INPUT 7& 8 VGA INPUTS
1
3
A separate output-1 & output-2 digital audio
port via RCA connector is provided for each
destination output. The digital audio signals
from HDMI input-1 or input-2 only
HDMI OUTPUTS
2
A separate output-1 & 2 HDMI ports with HDCP
is provided for each destination output.
Convert from CV/SV, YP P , VGA & HDMI
BR
A separate output-1 and 2 stereo audio signals
via 2x RCA connectors is provided for each
destination output.
VGA OUTPUTS
INPUT- 7& 8 AUDIO INPUTS
4
6
5
Input 7 is a stereo audio(AR/AL) with input 7 VGA.
Input 8 is a stereo audio(AR/AL) with input 8 VGA.
A separate output-1 and 2 VGA (RGBHV) signals
via 2x HD-15F female connectors is provided for
each destination output.Convert from CV/SV,
YP P , VGA & HDMI
BR
INPUT 5& 6 AUDIO INPUTS
7
INPUT 5& 6 COMPONENT VIDEO INPUTS
8
INPUT- 3&4 AUDIO INPUTS
INPUT- 3&4 S-VIDEO INPUTS
RS 232 CONTROL
9
11
INPUT- 3&4 COMPOSITE INPUTS
10
INPUT- 1&2 HDMI INPUTS
RS 485 CONTROL
12
14
13
RS 232 control port to allow for interfacing to a
PC.
IR EXTENDER CONTROL
15
DC POWER INLET
16
The SB-3877 is fitted with a DC power plug-park
input connector. Please ensure that the plug-park
used is of an approved type and is of sufficient
current carrying capacity with the correct voltage
and connector polarity. 12Volt DC power supply
3A Max.
Input 7 is a VGA(RGBHV) via HD-15P connector.
Input 8 is a VGA(RGBHV) via HD-15P connector.
Input 5 is a stereo audio(AR/AL) with input 5 component
Input 6 is a stereo audio(AR/AL) with input 6 component
Input 5 is a Component(YP P ) via RCA connector.
Input 6 is a
BR
Component(YP P ) via RCA connector. BR
Input 3 is a stereo audio(AR/AL) with input 3 component,
composite, or S-video
Input 4 is a stereo audio(AR/AL) with input 4 component,
composite, or S-video
Input 3 is a Composite Video via RCA connector.
Input 4 is a Composite video via RCA connector.
Input 3 is a S-Video(Y/C) via mini-4p connector.
Input 4 is a S-Video(Y/C) via mini-4p connector.
Input 1 is a HDMI(digital).HDCP compliant.
Input 2 is a HDMI(digital).HDCP compliant.
RS 485 control port to allow for interfacing to a
PC.
A separate IR Extender for output-1 and 2.
IR EXT.-1 is for output-1
IR EXT.-2 is for output-2

Step 1
Step 2
Step 3
PAGE 7
SB-3877 INSTRUCTION & OPERATION MANUAL
IR EXTENDER PACKAGE :
IR EXTENDER
INPUT
DC 12V
RoHS/95/EC
12
IR EXT.
RS-485
RS-232
TM
HIGH-DEFINITION MULTIMEDIAINTERFACE
REAR PANEL IR EXTENDER 1 & 2 PORTS
A separate IR Extender for Room-1 and 2.
IR EXT.-1 is for output-1
IR EXT.-2 is for output-2
IR EXTENDER CONTROL
HOW TO SETUP THE IR EXTENDER COMPONENTS
SB-100
SB-100
ON
OFF
POWER
OUT-1 OUT-2
SETRESOLUTION/OSD
SVGA XGA SXGA
WXGA WSXGA+ WUXGA
800x600 1024x768 1280x1024
1366x768 1680x1050 1920x1200
1234
5678
1234
5678
AUDIO-1 AUDIO-2
MULTIVIDEO8:2 MX SWITCHER
SW-3877
TV-1
TV-2
HDMI-1 HDMI-2 AV-SV-1 AV-SV-2
YPP-1BR YP P -2 BR VGA-1 VGA-2
HDMI-1 HDMI-2
AV-SV-1 AV-SV-2
YPP-1BR YP P -2 BR VGA-1 VGA-2
720p
1080p
VGA HDMI
ON
OFF
POWER
OUT-1 OUT-2
SETRESOLUTION/OSD
SVGA XGA SXGA
WXGA WSXGA+ WUXGA
800x600 1024x768 1280x1024
1366x768 1680x1050 1920x1200
1234
5678
1234
5678
AUDIO-1 AUDIO-2
MULTIVIDEO8:2 MX SWITCHER
SW-3877
TV-1
TV-2
HDMI-1 HDMI-2 AV-SV-1 AV-SV-2
YP P -1BR YP P -2 BR VGA-1 VGA-2
HDMI-1 HDMI-2
AV-SV-1 AV-SV-2
YP P -1BR YP P -2 BR VGA-1 VGA-2
720p
1080p
VGA HDMI
SB-100
SB-100
12
IR EXT.-1 output-1 for IR EXT.-2 output-2 for
ROOM-1 ROOM-2
300 M
300 M
PAGE 6 SB-3877 INSTRUCTION & OPERATION MANUAL
Before making any connections to the SB-3877. Observe the following:
> Ensure the mains voltage supply matches the label on the supplied plug-
Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a common point.
> Avoid powering equipment within a system from multiple power sources
that may be separated by large distances
REMOTE CONTROL
8
ON
OFF
POWER
OUT-1 OUT-2
SET RESOLUTION/OSD
SVGA XGA SXGA
WXGA WSXGA+ WUXGA
800x600 1024x768 1280x1024
1366x768 1680x1050 1920x1200
1234
5678
1234
5678
AUDIO-1 AUDIO-2
MULTIVIDEO 8:2 MX SWITCHER
SW-3877
TV-1
TV-2
HDMI-1 HDMI-2 AV-SV- 1 AV-SV- 2
YPP-1BR YPP-2 BR VGA-1 VGA-2
HDMI-1 HDMI-2
AV-SV- 1 AV-SV- 2
YPP-1BR YPP-2 BR VGA-1 VGA-2
720p
1080p
VGA HDMI
REMOTE CONTROL
> Connect all audio video sources and destination equipment
> power up all source and destination audio-visual sources
> For each destination output select the appropriate input source by using
> Upon power up the SB-3877 will return to its last used setting before
The front panel input 1&2 select buttons. The supplied IR remote control.
Or through the RS 232 / RS 485 serial communications port.
Powered down.
3 41 2
5 6
7
9
10
SWITCH POWER ON or OFF
1
Controller with a separate power ON and OFF
OUTPUT-1 RESOLUTION SET / OSD
Setup the output-1 resolutions or manual OSD
2
3
OUTPUT-2 RESOLUTION SET / OSD
Setup the output-2 resolutions or manual OSD
4
SELECT VGA OUTPUT RESOLUTIONS
Select VGA output resolutions as following :
SVGA 800x600, XGA 1024x768, SXGA 1280x1024
WXGA 1366x768, WSXGA+1680x1050, MAX.
WUXGA 1920x1200
5
SELECT HDMI OUTPUT RESOLUTIONS
Select HDMI output resolutions as following :
720P(1080x720), 1080P(1920x1200) MAX.
6
MANUAL OSD
OSD to setup or Adjust output resolutions and color.
7
AUDIO VALUE ADJUSTMENT
OSD to setup or Adjust output resolutions and color.
8
SELECT OUTPUT-1 SOURCES
output-1 for audio-video 1 to 8 source selections
9
10 SELECT OUTPUT-2 SOURCES
Output-2 for audio-video 1 to 8 source selections