Shinybow USA SB-5669K User manual

SB-5669K
16x16 UHD 4K2K HDMI Matrix Routing Switcher w/
Full EDID Management/Learning
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

CONTENTS
INTRODUCTION ..............................................................1
FEATURES.......................................................................2
SPECIFICATIONS............................................................3
FRONT PANEL ................................................................ 4
REAR PANEL ................................................................ 7
REMOTE CONTROL ....................................................... 8
EDID FUNCTIONS ......................................................... 10
TYPICAL APPLICATION ............................................... 15
IR EXTENDER ............................................................... 17
ETHERNET PROTOCOL ............................................. 19
RS-232 PROTOCOL .................................................... 20
INTRODUCTION
The SB-5669K is professional 16x16 matrix routing switch.
Supporting (16) HDMI Inputs and (16) HDMI outputs. The SB-
5669K is based on the HDMI standard and supports full resolution
HDMI Video with embedded HDCP, RS-232 and Bi-directional
IR. all over a single HDMI cable. With a signal bandwidth of
340Mhz, there is no signal degradation. High Denition Digital
signals can be selected and distributed to any (16) Inputs to (16)
Outputs. The SB-5669K is certied as being fully CEC and HDCP
1.3, HDMI 1.4a, HDMI 4K2K@30Hz, DVI 1.0, 3D formats, Wide
frequency range 25MHz ~ 340MHz. Supports UXGA/WUXGA/
DVI 1920x1200 resolution to any HD displays. The SB-5669K
has 16x HDMI connecter Input and 16xHDMI output, effectively
making this an 16 in x 16 out switcher. EDID management can
be selected between (7) different modes. Control is provided via
Front panel push buttons, IR remote, RS-232 or TCP/IP (not a
web-browser). An RS-232 Windows GUI interface is provided for
matrix routing control (Windows only).
PACKAGE CONTENTS
Check that you have the following components;
• SB-5669K Matrix Routing Switcher
• IR remote controller (SW-5669)
• 19-inch ear mount bracket (Part # 2U-440L) / ISO Screws
• IR extender SB-100 receiver (300M length)
• CD contents: Manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.50 feet (2M)
• Ethernet V2.0 / RS-232 V2.0 Protocol Instructions
• Users Guide
• Worldwide Universal Power Supply 100~240VAC, AC
50/60Hz, 10A
1
HDMI Matrix Routing Switcher Series
Thank you for purchasing the SB-5669K16x16 HDMI Matrix Routing Switcher. You will nd this unit easy to install and
highly reliable but it is essential that you read this manual thoroughly before attempting to use 16x16 HDMI Matrix Routing
Switcher.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent
© Copyright 2015. All Rights Reserved.
Version 2.0 JUNE 2015
5669K-20131212-001
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

FEATURES
• Enables switching of 16x HDMI digital source devices to 16x HDMI devices
• HDMI digital video w/embedded audio, DVI format and HDCP 2.2 compliant
• (7) function button control and worldwide (7) EDID modes for HDTV 4K2K resolutions
• Link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), support HDMI 1.4a 3D formats
• Wide range of HD resolutions from PC DVI XGA to WUXGA 1920x1200 and support HDTV/DTV resolutions 480i/480p, 576i/576p,
720p, 1080i & 1080p, 4K2K(3860x2160)
• Compatible with all HDMI source devices, PC monitors, plasma HD display, HDTV and audio receivers/ampliers
• Digital Video TMDS formats resolution up to 1080P-60 with deep color 36-bit.
• Digital Audio Support : Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2,
LPCM2
• Various user interface controls:
• Windows-based GUI control via RS-232 port
• Front panel push buttons
• IR wireless remote control
• Third party RS-232 controller (via simple ASCII)
• ETHERNET series interface (via pc protocol commands)
• Supports worldwide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
• Support EDID modes :
• Embedded EDID modes : 1. FSS (fast stard speed), 2. H24-3D, 3. H24-3D-M (multi Audio), 4. H36-3D, 5. H36-3D-M (multi
Audio), 6. 4K2K-3D PCM 2CH, 7. DVI-D 1920x1200-60Hz
• External modes : Learning mode (learning destination EDID link to source device)
• Automatic scanning of input & output status and display via LCM front panel
• Supports IR Remote and IR Extender with maximum distance up to ~ 1000’ (300M)
• EDID conguration via internal modes
SPECIFICATIONS
• Type of HDMI Switcher: 16x HDMI inputs to 16x HDMI outputs matrix switcher
• HDMI Support: HD 1080p@60Hz, 4K2K, H36-bit deep color, 3D (1.4a) formats
• HDCP Support: HDCP 2.0 Compliant
• Video Bandwidth: Double Data Rates: 340 MHz, total 6.7 Gbps bandwidth
• Digital Video Support: Full HD resolution: 480i / 480p / 720p / 1080i / 1080p / 4K2K
• Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES
6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Switcher Controls IR remote control
• IR external port x 1 (OD 3.5mm ear phone jack)
• Front panel buttons
• Ethernet and RS-232 serial interface
• Source Status: Automatic scanning of input status and display via LCM panel
• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
Infrared Frequency: 38 Khz
• IR Extend Distance: SB-100 (1000 feet / 300 meters maximum), SB-100C(2M)
• HDMI I/O Connector: HDMI Type A - SMD 19-pin female type
• Temperature: Operating Temperature 32°F - 100°F (0 °C - 32°C)
• Dimensions (LxWxH): 17.3 x 11.9 x 3.5 in (442x303x88mm)
• Rack Mount 2RU High 19 ”rack mount (with rack mount ears) #2U-440L
• Power Supply universal / worldwide type 50/60Hz, 110~240 VAC(120W)
• Unit material Metal (thin 1mm)
• Safety Approvals CE, FCC, RoHS (2002/95/EC), REACH
• Product Weight 4 Kgs / 8.82 lb
As product improvements are continuous, specications are subject to change and without notice.
2
FEATURES & SPECIFICATIONS

3
FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH: The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving
power. The switcher will remember the last setting during a power cycle. When power is removed and resorted, the last conguration will
be evoked.
2. INPUT STATUS DISPLAY: Input source 1 to 16 LED illuminate white to indicate a video source is present on that input.
3. OUTPUT STATUS DISPLAY: Each output (destination) channel shows which input (source) is assigned via LCM display.
4. DESTINATION SELECT BUTTONS: Separate outputs 1 thru 16 select buttons are provided for each destination assignment. Routing can be
Source to Destination or one source to multiple destinations.
Example: Press Destination 1, 3, 5, then press Source 2. The switcher will route Input 2 to Output 1,3,5 respectively.
5. EDID MODE SELECT BUTTONS: Use button #1 and #2 to select the desired EDID mode.
6. IR SENSOR: The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7. SOURCE SELECT BUTTONS: Input 1 thru 16 buttons are provided for each source selection.

4
FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR assign the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show ”0” to indicate none of the
destinations are assigned a video source.
Option 2
- Press ALL followed by Source 1 thru 16. The display will show the source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF
Disables (mute) video on the selected destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 16 output destination. The display will show “ 0 “ for the selected channel,
indicating no video selected.
10. FUNCTION KEY - RECALL
The system can save up to 16 sets of learning routes, which are stored in local memory using
Source buttons 1 thru 16 and Destination buttons 1 thru 16 as the memory preset location.
- Press RECALL button.
- Press 1 thru 16 on either Source or Destination row.
- Press ENTER The pre-set conguration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11. FUNCTION KEY - ENTER
Press ENTER to conrm entries.

5
FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY
The system can save up to 16 sets of switching routes, which are stored in local memory using
Source keys 1 thru 16 or Destination buttons 1 thru 16 as the memory location.
- Congure desired matrices .
- Press MEMORY button.
- Press 1 thru 16 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
13. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lock out the front panel (as shown on the left).
- Press and hold LOCK button for two seconds to enable the front panel (as shown on the
right).
14. FUNCTION KEY - EDID:
- Press EDID to begin setting up your EDID mode. Use source row buttons #1 and #2 to cycle
thru the options. ( Go to EDID setup instructions)

6
BACK PANEL
BACK PANEL
1. DC POWER INLET: The switcher is tted with a DC power plug input
connector. Ensure that the used is of an approved type and is of
sufcient current carrying connector capacity with the correct voltage
and connector polarity. power supply 100V~240VAC, 50/60Hz.
2. IR EXTENDER CONTROL: Supports one of IR Extender. Extends
maximum distance 300M / ~1000 feet. When you plug the external
IR extender into the switcher, the front panel IR receiver remains
active.
3. RS-232 CONNECTION: RS-232 control port allows interfacing to a
PC such as a computer or touch panel control, to the switcher via
this DB-9pin female connector for serial RS-232 control.
4. ETHERNET CONNECTION: Connects a CAT6/6a/7 category cable to
the Ethernet port for control of the switcher from a computer.
5. HDMI INPUTS 1 ~ 16: Connects a signal link of HDMI direct digital
video/audio to this female HDMI connector, which supports HDMI
digital video/audio and DVI digital video sources.
HDMI Digital Video/Audio, Connector with x screw
Input 1 ~ Input 16
6. HDMI OUTPUTS 1 ~ 16: Connects a signal link of HDMI direct digital
video/audio to this female HDMI connector, which supports HDMI
digital video/audio and DVI digital video sources.
HDMI Digital Video/Audio, Connector with x screw
Output 1 ~ Output 16
Power Jack:
DC Jack - Inner OD Ø 2.1 mm (+)
Outside OD Ø 5.5mm (GND)
Power Input: 100-240VAC, 50-60Hz 1.2A
IR Extender Jack: Female Jack - inner OD
Ø 3.5mm
Remote port: DB-9pin Female connector
8P8C / RJ 45 connector
HDMI digital video/audio connector:
HDMI Female connector.
Note: With proper adapters, the switcher
can be used with DVI digital video signals,
HDCP compliant.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With proper adapters, the switcher
can be used with DVI digital video signals,
HDCP compliant.

7
REMOTE CONTROL
Before making any connections observe the following:
• Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output select the appropriate input source by using the front panel input 1-16 select buttons. The supplied IR
remote control. Or through the RS-232 serial communications port.
• Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
IR REMOTE CONTROL KEY :
IR REMOTE : SW-5669
1. & 2. SWITCH POWER ON or OFF:
Controller with a power ON and OFF
3. DESTINATION : 1 thru 16 OUTPUT SELECTION:
Press the destination button to select the output display channel.
4. SOURCE : 1 thru 16 INPUT SOURCE SELECTION:
Press input 1~16 sources with selection button
5. FUNCTION KEY:
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
ENTER - function selection button
MEMORY - function selection button
LOCK - function selection button

8
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES : CUSTOM CODE : 32CD
POWER ON : 32CD A15E LOCK : 32CD B54A
POWER OFF : 32CD A25D RECALL : 32CD B24D
ALL : 32CD B04F ENTER : 32CD B34C
OFF : 32CD B14E MEMORY : 32CD B44B
EDID : 32CD B748
PRESS TV DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 32CD 10EF SOURCE #1 : 32CD 20DF
DESTINATION #2 : 32CD 11EE SOURCE #2 : 32CD 21DE
DESTINATION #3 : 32CD 12ED SOURCE #3 : 32CD 22DD
DESTINATION #4 : 32CD 13EC SOURCE #4 : 32CD 23DC
DESTINATION #5 : 32CD 14EB SOURCE #5 : 32CD 24DB
DESTINATION #6 : 32CD 15EA SOURCE #6 : 32CD 25DA
DESTINATION #7 : 32CD 16E9 SOURCE #7 : 32CD 26D9
DESTINATION #8 : 32CD 17E8 SOURCE #8 : 32CD 27D8
DESTINATION #9 : 32CD 18E7 SOURCE #9 : 32CD 28D7
DESTINATION #10 : 32CD 19E6 SOURCE #10 : 32CD 29D6
DESTINATION #11 : 32CD 1AE5 SOURCE #11 : 32CD 2AD5
DESTINATION #12 : 32CD 1BE4 SOURCE #12 : 32CD 2BD4
DESTINATION #13 : 32CD 1CE3 SOURCE #13 : 32CD 2CD3
DESTINATION #14 : 32CD 1DE2 SOURCE #14 : 32CD 2DD2
DESTINATION #15 : 32CD 1EE1 SOURCE #15 : 32CD 2ED1
DESTINATION #16 : 32CD 1FE0 SOURCE #16 : 32CD 2FD0
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list when press Destination # then press Source #
Press Destination # 1 & Source #1 32CD 01FE 32CD 20DF
Press Destination # 1 & Source #2 32CD 01FE 32CD 21DE
Press Destination # 1 & Source #3 32CD 01FE 32CD 22DD
Press Destination # 1 & Source #4 32CD 01FE 32CD 23DC

9
EDID FUNCTION
EDID FUNCTION SETUP
EDID Setup How to enter and exit
ENTER EXIT
EDID EDID
1. ENTER : After the switcher is powered on, the screen shows the main
page. Press EDID to enter the EDID setup page.
2. SELECT : EDID mode selection will show on the top. DES is an
abbreviation for destination buttons while SRC for source buttons.
Pressing source keys 1 and 2 enable you to cycle thru the 8 EDID modes.
Pressing destination buttons will enter learning mode.
3. EXIT : Press EDID again to exit. If exit before ENTER is pressed, the setup
will be cancelled. If the right bottom corner of the display shows LOCK, it
means the front panel buttons are locked and any button selections are not
available.
EDID Setup How to select an EDID mode
EDID SOURCE #1 or #2 Enter
In the EDID setup page, pressing the source button 1 and 2 will cycle thru the available selections.
Pressing source button 1 repeatedly to cycle UP.
Pressing source button 2 repeatedly to cycle DOWN.
A total of 8 embedded EDID modes are provided for selection.
When the desired mode is displayed, press Enter to conrm that selection.
The selected EDID mode will be applied to all destination and source devices.
1. Enter the EDID setup page and press source button 1 or 2 to cycle
through the 8 embedded EDID modes.
2. The left shows mode 2 as example. See the line 2. H24-3D, PCM 2 CH.
To select the mode, press enter button.
To go to next mode, press source 2.
To return to previous mode, press source 1.
* Operation will abort if no buttons are pressed within 5 seconds.
View the current EDID mode
The lower left shows the currently selected EDID mode. The left shows the currently selected mode is mode 2, H24-3D, PCM 2 CH.

10
EDID FUNCTION
EDID function : 7x Embedded EDID Modes
Mode 1. FSS (Fast Speed Start) Fast Speed Start mode shortens the startup time of the switcher. Selecting
this mode does not force the EDID setup to be cancelled. Users may rst
select one EDID mode from mode 2 to 8, and then select mode 1 for fast
speed start.
Mode 2. H24-3D (1080p-24 bits) Audio Support: PCM 2CH
Mode 3. H24-3D-M (1080p-24 bits) Audio Support: MAT(MLP) 7.1CH, PCM2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS5.1CH, PCM7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 4. H36-3D-M (1080p-36 bits) Audio Support: PCM 2CH
Mode 5. H36-3D (1080p-36 bits) Audio Support: MAT(MLP) 7.1CH, PCM2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS5.1CH, PCM7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 6. 4K2K Video Support: 4K2K-3D 3860x2160
Audio Support: PCM 2CH
Mode 7. 1920x1200-60Hz (DVI-D) DVI Support: DVI-D 1920x1200 60Hz

11
EDID FUNCTION
EDID FUNCTION : LEARNING
Learning EDID Single Destination to Single Source
EDID Destination 1 thru 16 Source 1 thru 16 Enter
Copy the EDID of a single destination device and pass it to a single source. The source device will output video and audio according
to the EDID of the destination.
1. Enter EDID setup page.
2. Choose one destination
Example: Select Destination 3
3. Then choose the intended source
Example: Select Source 4
Learning EDID Single Destination to Multiple / All Sources
EDID Destination 1 thru 16 Source 1 thru 16 Enter
Copy the EDID of a single destination device and pass it to multiple sources. The source device will output video and audio according
to the EDID of the destination.
1. Enter EDID setup page.
2. Choose one destination
Example: Select Destination 3
3. Then choose the intended source
Example: Select Source 1, 3, 5, 7.
Users who want all the 16 sources to learn the EDID from a destination, press all the 16 source buttons instead of the ALL button.

12
EDID FUNCTION
COMPARISON TABLE
Function Note
Learning
Mode
Let the source device(s) learn the EDID
from a single source and output video
and audio accordingly.
When a source devices has “learned” the EDID information of a destination
device, the switcher will save that EDID into EPROM and the stored EDID
cannot be altered. If you want to remove the EDID, set a new learning
route for the source.
FSS Mode
(Mode 1)
Shorten the startup time of the switcher. After the desired EDID setup is complete, use FSS mode and the switcher
will be faster at startup.
Mode 2 ~ 7 Let all source devices output the specied
video and audio formats.
Consult the spec documentation of your devices and select the mode that
best suits them.
TROUBLESHOOTING
INITIAL CHECKUP - FOR “NO SIGNAL”:
• Signal Compatibility – Make sure the display device accepts HDMI signal and the resolution it is being fed to.
• Cables – Check and see if the cables are damaged, crushed, or loosely connected. Replace cables with cuts or nicks. Tighten up
each connection to the plug. Cables longer than 15 meters may fail the signal transmission.
• Functional Connected Devices – Disconnect the devices from the switcher. Operate the devices in their intended use environment
and see if they are fully functional.
• Adapter – Use the supplied adapter or an adapter of sufcient current capacity, correct voltage, and connector polarity.
• AC Wall Outlet – The AC wall outlet should be installed near the unit and be easily accessible.
EDID SETUP:
• Inappropriate operation of the switcher may cause signal loss. To let the switcher recapture the EDID information, rst, power off
the switcher and all the connected devices. Then, power them on and reset the EDID mode.
• Switch back and forth between EDID mode 2 and mode 3 until both video and audio can be smoothly displayed.
• If none of the mode 2 to 7 suits all the connected devices, use mode 8 to let the switcher output the highest common resolution.
Please note setting the switcher in mode 8 may result in a compromised resolution.

Note:
The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
SB-100 IR Receiver Set
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
1. SB-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) IR Receiver (SB-100)
2. SB-100C IR 2M Receiver
Switcher IR EXT. In Cable (2C) IR Receiver (SB-100C)
Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
SB-100 IR Receiver Set
Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve
The SB-100 IR Receiver is required when using the port “ALL in” Jack.
The SB-100C IR Receiver will not function on the port “ALL in” Jack.
SB-100C Maximum Distance ~ 6 feet (2M)
IN P UT
DC 1 2V
R o H S /9 5 /E C
IR EXT .
RS -232
R S -23 2 IR E X T. i n
SB-100
IR Rx
POWE R
INPU T - 1
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
HDMI MATRIX SW IT CHE R
ONOFF
INPUT -2
INPUT -3
INPUT-4
SW IR
Distance: Max.(2M)
IR PN#: SW-XXXX
Control Switch SB-XXXX
SB-100 Maximum Distance ~ 984 feet (300M)
IN P UT
DC 1 2V
R o H S /9 5 /E C
IR EXT .
RS -232
R S -23 2 IR E X T. i n
SB-100
IR Rx
POWE R
INPU T - 1
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
HDMI MATRIX SW IT CHE R
ONOFF
INPUT -2
INPUT -3
INPUT-4
SW IR
Distance: Max.300M
IR PN#: SW-XXXX
Control Switch SB-XXXX
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
13
IR EXTENDER

14
RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION -2.0 COMPATIBLE
For a complete list of commands, please read the RS-232 Protocol Instruction
Manual.
RS-232 PROTOCOL COMMANDS (RS-232 Control driver V2.0.1)
The ShinybowUSA switcher can be controlled via the RS-232 serial control
port to allow for interfacing to a PC, or similar third party control system.
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1
stop bit - this is often referred to as 9600 8N1. When the unit recognizes a
complete command it will perform the requested action - there is no delimiter
character required.
ETHERNET SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document
extended Ethernet Protocol Instruction Manual.
ETHERNET TCP/IP PROTOCOL COMMANDS
(Ethernet / RS-232 Control driver V2.0.1 )
The ShinybowUSA switcher can be controlled via the TCP/IP serial
control port to allow for interfacing to a PC, or similar third party control
system.
The serial communication parameters are 9600 baud, 8 bit, No Parity
and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognizes a complete command it will perform the
requested action - there is no delimiter character required.
RS-232 SERIAL CONNECT
Pin RS-232 Denition
1 ------ Not used
2 TX Transmitter
3 RX Receiver
4 ------ Not used
5 GND Ground
6 ------ Not used
7 ------ Not used
8 ------ Not used
9 ------ Not used
RS-232 SERIAL INTERFACE
ETHERNET SERIAL INTERFACE
Pin Ethernet Reference
1 TXOP TX +
2 TXON TX -
3 RXIP RX +
4 NC
5 NC
6 RXIN RX -
7 NC
8 GND
Note :
Control the switcher
SPD : Speed
LINK : Ethernet link
RJ-45 Female 8P-8 Connector

INSTALLING DIAGRAM
Sample connection using IR transmitters (SB-101) and IR receiver (SB-100) with SB-6335T & SB-6335R to control a projector.
NOTE:
1. IR Control Projector Over HDBaseT™ Extender:
SB-6335 HDBaseT™ Transmitter
SB-6335R HDBaseT™ Receiver
2. RS-232 Control
3. External IR Remote.
4. IR Extender Transmitter : SB-101 IR Transmitter(300M), SB-101C (2M)
5. IR Extender Receiver : SB-100 IR Receiver (300M), SB-100C (2M)
16 HDMI inputs To 16 HDMI outputs Matrix Switcher using IR transmitters (SB-101) and IR receiver (SB-100).
15
TYPICAL APPLICATION

INSTALLING DIAGRAM
Example connection using IR transmitters (SB-101) and IR receivers (SB-100) with SB-6335T and SB-6335R to control a satellite
receiver.
NOTE:
1.IR Control Satellite Receiver Over HDBaseT™
CAT6/6a/7 extender from room:
SB-6335 HDBaseT™ CAT5e/6/7 Transmitter
SB-6335R HDBaseT™ CAT5e/6/7 Receiver
2. Audio Extractor To Recode Audio :
SB-5609 HDMI Audio Extractor.
3. Control HDMI ARC: SB-5610 ARC Control Box.
4. IR Extender Transmitter :
SB-101 (300M) Transmitter, SB-101(2M).
5. IR Extender Receiver :
SB-100 (300M) Receiver, SB-100(2M).
16 HDMI inputs To 16 HDMI outputs Matrix Switcher using IR transmitters (SB-101) and IR receiver (SB-100).
15
TYPICAL APPLICATION

16
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKEANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS,ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT

122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA
1-877-744-6987
1-972-377-2508
[email protected]
www.shinybowusa.com