SHO-ME 02.6216-6234-6252 User manual

1-09-08
Black
RED
WHITE
BLACK
RED
15
15
15
05.0410 Mounting
Bail
90.4524 Metal
Washer (2)
90.4424 Bolt (2)
90.4972 Cover (1)
90.4320 Machine
Screw (4)
05.0502 SPDT
Switch (2)
90.3939 Red
Pilot Lamp (4)
90.3804 10 AMP
Fuse (4)
02.6256 Circuit
Board Assembly
81.0198 #6 Blue
Spade Connnector (6)
81.0198 #6 Blue
Spade Connector (2)
41.0141.010Red (4')
41.0141.010Blk (4')
15
WHITE
RED
Black
44.2184 Cable Harness
90.3704 4-Way
Connector (2)
02.6020 20' Cable
Harness with Connector
ARROW BOARD AND BACK
PANEL NOT DRAWN TO SCALE
90.4006 #8 x
1/2" Phillips Pan
Screw (8)
90.4943 Back
Cover (2)
90.4942 Frame
(2)
Model No. 02.6216-6234-6252
LED Arrow Board
with Control Box
Installation and Maintenance Instructions
90.6756 Rubber
Gasket (10)
11.8516
11.8534
11.8552
PAR 36 LED(10)
17.0845.A00
PAR 36 Lens (10)
PRODUCTS COMPANY 804 East Hwy 248 Cassville, MO 65625
U.S. and Canada Toll Free Numbers Phone: [phone] FAX: [phone]
E-mail: [email protected] WEB: www.able2products.com
SHO-ME®

Installation and Maintenance Instructions
All connections are external. There is no need to open the control box during the installation process.
1. Mount the SHO-ME® Two Piece Arrow Board Panels on the vehicle as desired.
2. Route each cable from the Arrow Board to the drivers compartment or wherever the control box
will be located.
3. A mounting bracket is provided for easy installation of the control box. Determine a suitable
position for the mounting bracket and attach it to the vehicle with appropriate fasteners.
4. Connect the bare end of the HEAVY RED wire to a 12-volt positive power source.
5. Connect the bare end of the HEAVY BLACK wire to a suitable ground.
6. Connect the cable from the Arrow Board on the passenger's side of the vehicle to the quick
connect terminal marked "Right".
7. Connect the cable from the Arrow Board on the Driver's side of the vehicle to quick connect
terminal marked "Left".
8. Assemble the control box to the bracket.
**NOTE**
These instructions assume that the Arrow Boards are facing the rear of the vehicle. However, if the
arrow boards are flashing to the left when the pilot lamps on the control box indicate that they should
be flashing to the right and vice versa, then the Arrow Board Panel on the passenger side of the
vehicle should be connected to the terminal marked "Left", and the Arrow Board Panel on the Driver's
side should be connected to the terminal marked "Right".
After completing the installation, always check the direction that the Arrow Board Panels are flashing,
and be sure that it coincides with the direction indicated by the control box pilot lamps.
MAINTENANCE INSTRUCTIONS
TROUBLE SHOOTING
1. If the SHO-ME® Two Piece Arrow Board is not operating properly or is not lighting to full
brilliance, make sure all wire connections made during the installation process are secure and the
power source is active. Take particular care in making certain that ground connections are
properly made.
2. If the Arrow Board is still not working, check the internal 10 amp fuse, in the controller.
- 2 -

Wiring for 02.6216-6234-6252 Arrow Boards
Black
Red
-
-
Ground
+12V
SHO-ME®
Made In U.S.A.
RRBB WW
-
+
Red to Yellow
White to Yellow
Black to Black
White to Yellow
Red to Yellow
Black to Black
- 3 -