ShoreStation DA0017-15 User manual

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
ACCESSORY
DA0017-15
Dock Ladder - Stationary Dock
DA0017-15 Bundles Required
6944915 Dock Ladder Bundle - Alum 5 Step
6713700 Mounting Bracket Bundle
DA0041-15
Dock Ladder - Floating Dock
SBA017-15 Bundles Required
6944915 Dock Ladder Bundle - Alum 5 Step
7079615 ShoreBridge Ladder MTG Kit
SBA017-15
Dock Ladder - ShoreBridge
DA0041-15 Bundles Required
6944915 Dock Ladder Bundle - Alum 5 Step
6947915 Floating Dock Connector Weldment

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
DA0017-15

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
DA0041-15

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
SBA017-15

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
DA0017-15 Stationary Dock Assembly Instructions
• Breakthebundlesandsortallitemsbysize.
• Locatethedockaccessorymountingbracketusedtoattachac-
cessoriestothedocklegframe.
• Locatethedockladdermountingbracketweldment.
• Orientatethetwopartsasshowninthedrawing.Notethatthe
mounting brackets will position the ladder so it will set at an
anglewhenpositonedcorrectly.
• Aligntheholesinthetwoweldmentsasshown.Attachthetwo
weldmentstogetherbyplacingfour(4)3/8”x3/4”carriagebolts
inthealignedholes.Notetheheadsoftheboltsmustbeplaced
asshownsothesquareportionofthecarriageboltmateswith
thesquareholespunchedinthedockladdermountingbracket.
• Securewithfour(4)3/8”lockwashersandhexnuts.Tighten.
Installation Instructions
• Eachstationarydocklegframehasasetoffourearsonwhich
thedockaccessorymountingbracketwillattach.
• Simplyraisetheaccessorymountingbrackettothetopofthe
docklegsothedockaccessorymountingbracketcanthenbe
slippedontothedocklegabovetheears.
• When the dock accessory mounting bracket is completely on
thedockleg,slideitdownthelegovertheears.Lettheminter-
locksecuringthedockaccessorymountingbrackettotheleg.
• Notethattherungsoftheladderarespacedsothatonerung
oftheladderwillslideoverthetopsquaremountingtubewhile
therungbelowwillslipoverthenextsquaretube.Thisallows
theladdertobeadjustedupordownwithrespecttothewater
level.
• Placetheladderrungsontothesquaretubesofthedockladder
mountingbracket.Pressthespringloadedretainerpinslocated
inthetopsquaretubesotheladderwillslidecompletelyover
thetubes.Whenfullydownonthesquaretubes,thespringpins
willsnapintotheholesprovidedintheladderrunglockingitin
thisposition.
• Toadjusttheheightoftheladderortoremovetheladder,simply
pressthespringloadedpinsinandraiseupontheladder.Re-
positiontonewlocation.
• Assemblyandinstallationarecomplete.
Safety Instructions
•Read and understand the contents of this manual before installing or using the ladder.
•This dock ladder is designed for use with ShoreStation dock systems only. Never modify or use
the ladder for other purposes.
•Never leave children unattended on the on or around the ladder.
•One person should use the ladder at a time.
•Inspect all components and fasteners regularly for damage, tightness, and deterioration. Replace
any damaged component before using the ladder.
•Retract the ladder from the water when it is not in use to prevent ‘slime’ build up.
•Check both snap buttons to ensure they are fully engaged before using the ladder.

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003724
REV D 12/09/2010
SBA017-15 ShoreBridge Assembly Instructions
 • Breakthebundlesandsortallitemsbysize.
 • LocatetheShoreBridgemountingbracketusedtoattach
thedockladdermountingbrackettothedockframe. 
 • Mountbracket tothe longuprights inthe side,this will
not mount to the center upright, using 3/8 X 2 & 7/16 X 3
square u-bolts and securing with stainless steel at washers
andbrasslocknutswithnyloninserts.   
•Locatethedockladdermountingbracketweldment.
• Orientate the two parts as shown in the drawing.  Note
thatthemountingbracketswillpositiontheladdersoitwillsetat
ananglewhenpositonedcorrectly.
 • Align the holes in the two weldments as shown.Attach
thetwoweldmentstogetherbyplacingfour(4)3/8”x3/4”car-
riageboltsinthealignedholes.Notetheheadsoftheboltsmust
beplacedasshownsothesquareportionofthecarriagebolt
mateswiththesquareholespunchedinthedockladdermount-
ingbracket.
 • Securewithfour(4)3/8”lockwashersandhexnuts.Tight-
en.
Installation Instructions
 • Notethattherungsoftheladderarespacedsothatone
rungoftheladderwillslideoverthetopsquaremountingtube
while the rung below will slip over the next square tube. This
allowstheladdertobeadjustedupordownwithrespecttothe
waterlevel.
 • Placetheladderrungsontothesquaretubesofthedock
laddermountingbracket.Pressthespringloadedretainerpins
locatedinthetopsquaretubesotheladderwillslidecompletely
overthetubes.Whenfullydownonthesquaretubes,thespring
pinswillsnapintotheholesprovidedintheladderrunglocking
itinthisposition.
 • Toadjusttheheightoftheladderortoremovetheladder,
simplypressthespringloadedpinsinandraiseuponthelad-
der.Repositiontonewlocation.
 • Assemblyandinstallationarecomplete.
DA0041-15 Floating Dock Assembly Instructions
• Breakthebundlesandsortallitemsbysize.
• Locatetheoatingdockconnectorweldmentandthedocklad-
dermountingbracket.Seepartsdiagram.
• Aligntheholesinthetwoweldmentsasshown.Attachthetwo
weldmentstogetherbyplacingfour(4)3/8”x3/4”carriagebolts
inthealignedholes.Notetheheadsoftheboltsmustbeplaced
asshownsothesquareportionofthecarriageboltmateswith
thesquareholespunchedinthedockladdermountingbracket.
• Securewithfour(4)3/8”lockwashersandhexnuts.Tighten.
Installation Instructions
• Selecttheposition ontheoatingdock thattheladderwill be
mounted.
• Removethe3/8”x2”hexboltassemblyfromthetopsideofthe
oatingdockconnectorweldment.
• Insert the oating dock connector weldment into the selected
notchmoldedinthesideoftheoatingdocksection.Raisethe
unitup.Secureinplaceusingtheboltassemblyjustremovedin
thepreviousstep.Tighten.
• Notethattherungsoftheladderarespacedsothatonerung
oftheladderwillslideoverthetopsquaremountingtubewhile
therungbelowwillslipoverthenextsquaretube.Thisallows
theladdertobeadjustedupordownwithrespecttothewater
level.
• Placetheladderrungsontothesquaretubesofthedockladder
mountingbracket.Pressthespringloadedretainerpinslocated
inthetopsquaretubesotheladderwillslidecompletelyover
thetubes.Whenfullydownonthesquaretubes,thespringpins
willsnapintotheholesprovidedintheladderrunglockingitin
thisposition.
• Toadjusttheheightoftheladderortoremovetheladder,simply
pressthespringloadedpinsinandraiseupontheladder.Re-
positiontonewlocation.
• Assemblyandinstallationarecomplete.