Show Tec SC-2412 User manual

SC-2412 V3
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 50710
MANUAL
ENGLISH

1
Ordercode: 50710
SC-2412
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Connection with the mains.........................................................................................................................................4
Description of the device.................................................................................................................................................6
Overview ........................................................................................................................................................................6
Frontside..........................................................................................................................................................................7
Backside .......................................................................................................................................................................11
Installation.........................................................................................................................................................................11
Set Up and Operation .....................................................................................................................................................11
Glossary.........................................................................................................................................................................12
Operations ........................................................................................................................................................................13
Physical Fader Assignment........................................................................................................................................13
Example .....................................................................................................................................................................14
Switching Between Page A and Page B (channels 1-24 and 25-48) ...............................................................14
Recording.....................................................................................................................................................................15
Create a Scene/Chase ..........................................................................................................................................15
Edit a Scene/Chase ................................................................................................................................................16
Delete a Scene/Chase...........................................................................................................................................17
Delete All Scenes/Chases ......................................................................................................................................18
Delete a Scene/Chase From Temporary Memory............................................................................................18
Delete a Single Scene in a Chase........................................................................................................................19
Insert a Scene into a Chase...................................................................................................................................20
Playback.......................................................................................................................................................................21
Playing a Scene/Chase..........................................................................................................................................21
Playing a Scene/Chase With Audio Triggering ..................................................................................................22
Playing a Scene/Chase While Adjusting Speed With the Speed Fader .......................................................22
Playing a Scene/Chase With the Stored Beat ...................................................................................................23
Change the Speed Mode Between 5 and 10 Minutes....................................................................................23
Auxiliary Controls.........................................................................................................................................................24
MIDI Operations ..........................................................................................................................................................25
Setting Up MIDI In.....................................................................................................................................................25
Setting Up MIDI Out .................................................................................................................................................26
Receiving MIDI File Dump ......................................................................................................................................26
Sending MIDI File Dump..........................................................................................................................................27
Maintenance....................................................................................................................................................................27
Troubleshooting ...............................................................................................................................................................28
No Light.........................................................................................................................................................................28
Product Specifications....................................................................................................................................................28
Appendix 1: Midi Implementation ...............................................................................................................................29

2
Ordercode: 50710
SC-2412
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
●Showtec SC-2412
●AC power adapter 12V DC, 500mA
●User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 50710
SC-2412
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●Never remove warning or informative labels from the unit.
●Do not open the device and do not modify the device.
●Never use anything to cover the ground contact.
●Never leave any cables lying around.
●Do not insert objects into air vents.
●Do not connect this device to a dimmer pack.
●Do not switch the device on and off in short intervals, as this would reduce the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device. Never use the
device during thunderstorms, unplug the device immediately.
●Only use device indoors, avoid contact with water or other liquids.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always keep case closed while operating.
●Always allow free air space of at least 50 cm around the unit for ventilation.
●Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
●Make sure that the device is not exposed to extreme heat, moisture or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●If the external cable is damaged, it has to be replaced by a qualified technician.
●If device is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. The unit must be installed out of the reach of children. Never leave the unit
running unattended.
●For replacement use fuses of same type and rating only.
●The user is responsible for correct positioning and operating of the SC-2412. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
●Repairs, servicing and electric connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.

4
Ordercode: 50710
SC-2412
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The maximum ambient temperature ta = 40°C must never be exceeded.
●In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
●The relative humidity must not exceed 50 % with an ambient temperature of 40°C.
●If this device is operated in any other way, than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious injuries and/or damage of property!

5
Ordercode: 50710
SC-2412
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

6
Ordercode: 50710
SC-2412
Description of the device
Features
The SC-2412 is a 24-channel light controller from Showtec.
●48 patchable channels & 2 AUX channels
●MIDI functionality
●24 channel faders
●LCD display for easy setup
●Programmable Speed and Fade time
●3-pin and 5-pin XLR outputs
●Patchable channels
●Desktop and 19-inch model
●User record code
●Power adapter: DC 12-18V 800mA Min.
●DMX output: 3-pin XLR OUT
●MIDI signal: 5-pin standard interface
●Audio input: 100 mV~1Vpp
●Internal fuse: F0.5A 250V 5x20
●Dimensions:
483 x 264 x 92 mm (LxWxH)
19” x 6HE
●Weight: 4,1 kg
Note: Knowledge of DMX and MIDI is required to fully utilize this unit.
Overview
Fig. 01

7
Ordercode: 50710
SC-2412
Frontside
Fig. 02
01) DMX channel LEDs
The LEDs indicate the status of the DMX channels 1-24 (when page A is selected) and 25-48 (when
page B is selected).
02) Channel faders
These faders allow you to control DMX channels 1-24 (when page A is selected) and DMX channels
25-48 (when page B is selected) or to use them for programming scenes/chases, when in Record
mode. The faders 13-24 can also be used for starting/stopping scenes for playback.
03) Flash buttons
Pressing a flash button will send the value of 100% to the respective DMX channel. The flash buttons
control DMX channels 1-24 (when page A is selected) and DMX channels 25-48 (when page B is
selected). The flash buttons 13-24 can also be used for storing scenes, speed settings for a particular
scene and deleting scenes in Program mode or Edit mode. Press and hold down the record/shift (14)
button, and press the flash buttons 1-12 to enter different program modes:
●Press the #6 three times: Patch mode.
●Press the #1-#5-#6-#8: Program mode.
04) Chase LEDs
These LEDs indicate the status of chases 1-12.

8
Ordercode: 50710
SC-2412
05) Park button
Press this button to select either Single chase
mode or Mix chase mode. In Single chase
mode you are only able to playback a single
scene. In mix mode you are able to playback
several scenes simultaneously. Move the
faders 13-25 to set the master intensity for the
respective scene (fader 13: scene 1, fader 14:
scene 2 etc.). Chase mode is indicated by the
Chase mode indicator (15).
06) Up/chase rev
Press this button to modify a scene while in Edit
mode. In combination with the record/shift
(14) button, this button allows you to reverse
the direction of a chase while in Playback
mode.
07) Delete/rev one
Press this button to delete a step or chase
while in Edit mode. In combination with the
record/shift (14) button, this button allows you
to reverse the direction of a single chase while
in Playback mode.
Fig. 03
08) Page/record clr button + page LEDs
Each page can contain 12 scene/chases. This means that you can store up to 48 scenes/chases.
09) Aux 1 control + button
The aux control and button can be assigned to any DMX channel. Each aux control can be set in
three modes:
●Mode 1: The control is not assigned to a DMX channel.
●Mode 2: The control and control button work as a normal channel fader and flash button (max.
brightness).
●Mode 3: The control is used for adjusting the brightness of the flash button.
10) Insert/% or 0-255
Press this button to insert one or more steps (scenes) into a chase. Press and hold down the
record/shift (14) button, and press this button to switch the DMX output value on the display as either
0-100% or 0-255.
11) Aux 2 control + button
The aux control and button can be assigned to any DMX channel. Each aux control can be set in
three modes:
●Mode 1: The control is not assigned to a DMX channel.
●Mode 2: The control and control button work as a normal channel fader and flash button (max.
brightness).
●Mode 3: The control is used for adjusting the brightness of the control button.
12) Add kill/rec exit
Press this button to enter Add mode, Kill mode or exit Record mode. In Add mode, this button allows
you to activate multiple scenes or flash buttons. In Kill mode, selecting a scene or a flash button will
kill any other active scene program. In Record mode, in combination with the record/shift (14)
button, this button allows you to exit Record mode.
13) Edit/all rev
Press this button to activate Edit mode. Press this button, while holding down the record/shift (14)
button, to reverse the direction of all chases.

9
Ordercode: 50710
SC-2412
14) Record/shift
Press this button to enter Record mode or to
access the secondary (shift) functions of a
button.
15) Chase mode indicator
Indicates if the SC-2412 is in Mix chase mode
(orange LED) or Single chase mode (red LED).
16) Audio/page A-B button
Press the button to enter Audio mode or
switch between page A and page B (in
combination with the record/shift (14) button).
17) Step button + LED
Press the button to step through a chase when
the speed fader (20) is in max. position
(completely down).
18) 5-10 min LEDs
Indicates if the SC-2412 is in Mix or Single
mode.
19) Audio level fader
Move the fader to adjust the sensitivity for the
built-in microphone or the audio input jack at
the rear, while using audio triggering.
Fig. 04
20) Speed fader
Move the fader to adjust the speed for the scenes in Program mode or in Playback mode.
21) Fade fader
Move the fader to adjust the fade time in Playback mode.
22) Home button
Press this button to release a DMX channel, which is in Blind mode, and return to normal chase
playback. See page 10: Blind (35) button.
23) Hold button
Press this button to toggle Hold mode on or off. The status of this mode is indicated by the green LED
located above the button. Activating this mode during Chase playback will hold a scene until you
deactivate Hold mode.
24) Tap sync button
Tap this button to sync the speed during chase playback.
25) Full on button
Press this button to set all 48 DMX channels to 100%.
26) Black out button
Press this button to kill all output.
27) LCD display
Shows the current activity or the programming state.
28) Down/beat rev button
Press this button to modify a scene while in Edit mode. In combination with the record/shift (14)
button, this button allows you to reverse the direction of a chase while the chase is in Audio control
mode.

10
Ordercode: 50710
SC-2412
29) Dark button
Press this button to mute all output as long as
the button is pressed.
30) Mode indicator button
The mode indicator indicates if you are in:
●Chase scene mode: Press to
program/playback scenes/chases.
●A double preset B mode: In this mode you
can use the channel faders to set up two
presets for DMX channels 1-12. Preset 1:
faders #1 - #12, preset 2: faders #13 - #24.
Switch/fade between two presets by
moving the master A (33) and master B
(34) faders simultaneously up or down.
●Single preset park mode: Allows you to set
up scenes.
31) Master A button
This is a flash button for the master A fader.
Regardless of the setting of the master A
fader, pressing this button has the same effect
as moving the master A fader to its maximum
position.
32) Park button
While in Chase <> scene mode, press this
button to switch between Single chase mode
and Mix chase mode. The selected mode is
indicated by the chase mode indicator (15).
While in double preset mode, pressing this
button has the same function as moving the
master B (34) fader completely up.
While in Single preset mode, pressing this
button allows you to temporally record the
current output while adjusting the master B
(34) fader.
Fig. 05
33) Master A fader
Move this fader to adjust the overall output level. This fader controls the overall output of all
channels.
34) Master B fader
Move this fader to adjust the overall output level. This fader controls the chase of all programs.
35) Blind button
Press and hold down this button and tap the corresponding channel’s flash button to release the
channel’s fader from the currently playing chase. Move the fader to control the selected channel
independently of the chase. Return from Blind mode by pressing and holding down the home (22)
button while tapping the fader(s) you released while in Blind mode.

11
Ordercode: 50710
SC-2412
Backside
Fig. 06
36) 3-pin DMX connector OUT
37) 5-pin DMX connector OUT
38) Polarity switch
39) MIDI connector THRU
40) MIDI connector OUT
41) MIDI connector IN
42) Audio Input
Connect a line level audio input signal ranging from 100 mV to 1Vpp.
43) Remote input
Blackout and full can be controlled by a remote control with a 1/4“ jack connection.
44) DC input
Connect a 12-18V DC, 800mA min. adapter.
Installation
Remove all packing materials from the SC-2412. Check if all foam and plastic padding is removed.
Fit the equipment to a 19" rack. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.

12
Ordercode: 50710
SC-2412
Glossary
●Blackout is a state where all lighting fixtures’ light outputs are set to 0 or OFF.
●Chases are a number of scenes played in sequence. A program which consists of several scenes
(steps) is called a chase while a program which consists of a single scene (step) is called a scene.
●DMX-512 is an industry standard digital communication protocol used in entertainment lighting
equipment. For more information read Sections “DMX Primer” and “DMX Control Mode” in the
Appendix (page 29).
●Fixture refers to your lighting instrument or other device such as a fogger or dimmer which you can
control.
●Scenes are static lightning states.
●Faders are also known as sliders.
●Scanner refers to a lighting instrument with a pan and tilt mirror; however DMX controllers can use this
term to control any DMX-512 compatible device as a generic fixture.
●MIDI is a standard for representing musical information in a digital format. A MIDI input would provide
external triggering of scenes using MIDI devices such as a MIDI keyboard.
●Stand Alone refers to a fixture’s ability to function independently of an external controller and usually
in sync with music, thanks to a built-in microphone.
●Fade fader is used for adjusting the fade time between scenes within a chase.
●Speed fader affects the amount of time a scene will hold its state. It is also known as wait time.
●Shutter is a mechanical device in the lighting fixture that allows you to block the light’s path. It is
often used to lower the intensity of the light output and of the strobe.
●Patching refers to the process of assigning faders to a DMX channel within a fixture.
●Playbacks can be either scenes or chases that are directly called to execution by the user. A
playback can also be considered a program memory that can be recalled during a show.

13
Ordercode: 50710
SC-2412
Operations
Physical Fader Assignment
Use this feature to combine or unify fixture control attributes for different fixtures.
For example, if controlling 4 moving mirrors and 4 moving yokes, the color, gobo and dimmer channels
may not line up ideally on the physical faders. Use this function to re-assign the dimmer, color and gobo
channels to faders 1, 2 and 3. From now on you will be able to control the same attributes on all fixtures
using the same fader location.
01) Select the page which the DMX channel (CHNO) you wish to
assign is on.
02) Press and hold down the record/shift (14) button and tap the
audio/page A B (16) button to toggle between page A and
page B. The selected page is shown on the LCD display (27).
03) While holding the record/shift (14) button, tap flash button #6
(03) three times.
04) Tap the flash (03) button of the DMX channel (CHNO) you want
to assign to a fader.
●Page A selected: faders 1-24
●Page B selected: faders 25-48
05) If you want to assign a DMX channel (CHNO) to a fader from the
page different to the one you are on at the moment, press and
hold down the record/shift (14) button, while tapping the add
kill/rec exit (12) button to exit Fader assignment mode. If the
fader is on the same page, proceed with step 8.
06) Select the page which the DMX channel (CHNO) you wish to
assign is on. Press and hold down the record/shift (14) button
and tap the audio/page A B (16) button to toggle between
page A and page B. The selected page is shown on the LCD
display (27).

14
Ordercode: 50710
SC-2412
07) While holding down the record/shift (14) button, tap flash #6 (03)
button three times.
08) Press and hold down the record/shift (14) button, while tapping
the flash (03) button of the fader you wish to assign the DMX
channel to.
●Page A selected: faders 1-24
●Page B selected: faders 25-48
09) Repeat steps 3-8 as often as necessary.
10) Press and hold down the record/shift (14) button and press the
add kill/rec exit (12) button to exit Fader assignment mode.
Example
You wish to assign DMX channel 001 to fader #5.
01) Press and hold down the the record/shift (14) button and tap flash #6 (03) button three times.
02) Press flash #1 (03) button.
03) While holding down the record/shift (14) button, press flash #5 (03) button.
04) Press and hold down the record/shift (14) button while tapping the add kill/rec exit (12) button, in
order to exit Fader assignment mode.
Notes
●All physical faders can be re-assigned to output on a different DMX channel. Faders are given a
channel number and are labeled on the controller.
●It is possible to check the assignments by pressing the fader button of the corresponding channel
while in this mode.
●There is no limit of the amount of channels that can be assigned to faders. One can assign all 48
channels of DMX output to a single fader.
●CHNO corresponds with the channel number, while SLDNO corresponds with the physical fader
number.
Switching Between Page A and Page B (channels 1-24 and 25-48)
Press and hold down the record/shift (14) button and tap the
audio/page A B (16) button to toggle between page A and page B.
Notes
●When you switch the fixture on, it will return to the previously used page.
●Page A is used for controlling channels 1-24, while Page B –channels 25-48.
●The display will show the currently active page.
●There is an additional set of 4 pages of playback controls on Page B.

15
Ordercode: 50710
SC-2412
Recording
Create a Scene/Chase
01) While holding down the record/shift (14)
button, tap the flash (03) buttons #1-5-6-
8 in sequence.
02) Release the record/shift (14) button.
The record LED will light up. Now you are
in Program mode (record enable).
03) Select the 1-24 Single mode by tapping the mode select/rec
speed (05) button. It will give you control of all 24 channels
located on the first page.
04) Compose a scene by moving the channel faders (changes in
fixture attributes such as colors and gobos, or simply dimmer
values).
05) Tap the record/shift (14) button to store the scene into the
temporary memory.
06) If you wish to create a chase, add scenes by repeating steps 2-4
until you have created your desired chase.
07) Tap the page (8) button to select the page (1-4) on which you
want to store your scene/chase.
08) Press and hold down the record/shift (14) button and tap the
flash (03) button for the memory number indicated by the scene
LED (1-12) in which you want to store your scene/chase. All LEDs
will flash briefly, indicating the scene/chase has been stored in
the memory. Flash buttons 13-24 allow you to store
scenes/chases in memory 1-12.

16
Ordercode: 50710
SC-2412
09) You can continue programming or exit. To exit Program mode,
press and hold down the record/shift (14) button and tap the
add kill/rec exit (12) button.
Notes
●Leave Blackout mode if the blackout LED is on, by tapping the blackout (26) button.
●Be sure that you are on the right page by viewing the display which will show page A or page B. This
will enable 1-24 or 25-48 channel control.
●If you just wish to create a static look (= scene), then you must create a chase composed of only 1
scene (step).
●You can add up to 1000 scenes (steps) available in every chase.
Edit a Scene/Chase
01) While holding down the record/shift (14)
button, tap the flash (03) buttons #1-5-6-
8 in sequence.
02) Release the record/shift (14) button.
The record LED will light up. Now you are
in Program mode (record enable).
03) Press the page (08) button to select the page which the
scene/chase you want to edit is on.
04) Select Chase < > scene mode by tapping the mode select/rec
speed (05) button. It will give you control of all 24 channels on
the first page.
05) Press and hold down the edit/all rev (13) button.
06) While holding down the edit/all rev (13) button, tap the flash
(03) button corresponding with the scene/chase you want to
edit.
07) Release the edit/all rev (13) button. The relevant scene LED will
light up, indicating that the scene is in Edit mode.

17
Ordercode: 50710
SC-2412
08) Tap the step button (17) until you reach the scene you want to
edit.
09) Press and hold down the up/chase rev (06) button if you want to
increase the output value of a DMX channel.
10) Press and hold down the down/beat rev (28) button if you want
to decrease the output value of a DMX channel.
11) While holding down either the up/chase rev (06) button or the
down/ beat rev (28) button, tap the corresponding flash button
to respectively increase or decrease that channel’s DMX output.
12) Repeat steps 8-11 until all scenes have been edited.
13) Exit Program mode, press and hold down the record/shift (14)
button and tap the add kill/rec exit (12) button.
Delete a Scene/Chase
01) While holding down the record/shift (14)
button, tap the flash (03) buttons #1-5-6-
8 in sequence.
02) Release the record/shift (14) button.
The record LED will light up. Now you are
in Program mode (record enable).
03) Press the page (08) button to select the page which the
scene/chase you want to delete is on.
04) While holding down the edit/all rev (13) button, tap the flash
(03) button, corresponding with the scene/chase you want to
delete, twice.
05) Release the edit/all rev (13) button. All LEDs will flash briefly,
indicating that the scene/chase has been deleted.

18
Ordercode: 50710
SC-2412
Delete All Scenes/Chases
01) While holding down the record/shift (14)
button, tap the flash (03) buttons #1-3-2-
3 in sequence.
02) Press and hold down the record/shift (14) button and tap the
add kill/rec exit (12) button.
Notes
●You must be in Record mode to reset the controller.
●The LED above the record button will light up, indicating that Record mode is active.
●Parameters can be edited while a chase is running.
This action will reset the controller to its factory default settings.
This will erase all programs and settings.
Delete a Scene/Chase From Temporary Memory
01) If you are not satisfied with a chase, while programming, (as described on pages 15-16: Create a
Scene/Chase), you have the option to delete the chase without leaving Program mode.
02) Press and hold down the record/shift (14) button while tapping
the page/record clr (08) button. All LEDs will flash, indicating that
the scene/chase is deleted.
Notes
●All the scenes stored in the temporary memory of the controller will be erased in this process.
●This process will not affect the scenes already programmed into a scene/chase fader.

19
Ordercode: 50710
SC-2412
Delete a Single Scene in a Chase
01) While holding down the record/shift (14)
button, tap the flash (03) buttons #1-5-6-
8 in sequence.
02) Release the record/shift (14) button.
The record LED will light up. Now you are
in Program mode (record enable).
03) Press the page (08) button to select the page which the
scene/chase you want to edit is on.
04) Select Chase < > scene mode by tapping the mode select/rec
speed (05) button. It will give you control of all 24 channels on
the first page.
05) Press and hold down the edit/all rev (13) button.
06) While holding down the edit/all rev (13) button, tap the flash
(03) button corresponding with the chase in which there is the
scene you want to delete.
07) Release the edit/all rev (13) button. The relevant scene/chase
LED will light up, indicating that the chase is in Edit mode.
08) Tap the step (17) button until you reach the scene you want to
delete.
09) Tap the delete/rev one (07) button to delete the current scene.
All LEDs will light up, indicating that the current scene is deleted.
10) Repeat steps 8-9 until all unwanted scenes are deleted.
11) Exit Program mode, press and hold down the record/shift (14)
button and tap the add kill/rec exit (12) button. The scene LED
will dim indicating that you left Edit mode.