Show Tec EventLITE 4/10 Q4 Set 6x User manual

EventLITE 4/10 Q4 Set 6x V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 44061
MANUAL
ENGLISH

1
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Table of contents
Warning ...............................................................................................................................................................................3
Safety Instructions ........................................................................................................................................................3
Operating Determinations .........................................................................................................................................5
Rigging ...........................................................................................................................................................................5
Connection with the mains........................................................................................................................................6
Return Procedure .........................................................................................................................................................7
Claims.............................................................................................................................................................................7
Description of the device.................................................................................................................................................8
Overview (EventLITE 4/10 Q4)....................................................................................................................................9
Bottom (EventLITE 4/10 Q4) ........................................................................................................................................9
Overview (Charging case) ......................................................................................................................................10
Installation.........................................................................................................................................................................11
Adjusting the Tilt Angle..............................................................................................................................................11
Setup and Operation ......................................................................................................................................................11
Charging the Built-in Battery ....................................................................................................................................11
Control Modes ............................................................................................................................................................12
One EventLITE (Auto) ..............................................................................................................................................12
One EventLITE (Built-in programs) .........................................................................................................................13
One EventLITE (Manual) .........................................................................................................................................13
Multiple EventLITEs (Master/Slave control)..........................................................................................................13
Multiple EventLITEs (Wireless Master/Slave control)...........................................................................................14
Multiple EventLITEs (DMX Control) ........................................................................................................................15
Multiple EventLITEs (Wireless DMX Control) .........................................................................................................16
Connect the EventLITE to the Wireless DMX Signal Transmitter ......................................................................17
Disconnect the Event LITE From the Wireless DMX Signal Transmitter............................................................17
Fixture Linking ..............................................................................................................................................................18
Data Cabling ..............................................................................................................................................................18
Control Panel ..............................................................................................................................................................19
DMX Control Mode....................................................................................................................................................19
DMX Addressing .........................................................................................................................................................19
Menu Overview ..........................................................................................................................................................20
Main Menu Options ...................................................................................................................................................22
1. DMX ........................................................................................................................................................................22
1.1. Address...............................................................................................................................................................23
1.2. Channels ............................................................................................................................................................23
1.3. Signal...................................................................................................................................................................23
1.4. W-DMX Unlock ..................................................................................................................................................24
2. Manual...................................................................................................................................................................24
2.1. Color Save .........................................................................................................................................................24
3. Auto........................................................................................................................................................................25
4. Program.................................................................................................................................................................25
5. Master/Slave Mode.............................................................................................................................................26
6. Settings...................................................................................................................................................................26
6.1. Curves Select ....................................................................................................................................................27
6.2. Dimmer Speed ..................................................................................................................................................27
6.3. Economy ............................................................................................................................................................28
6.4. Backlight Time ...................................................................................................................................................28
6.5. DMX Fail..............................................................................................................................................................28
6.6. IR ..........................................................................................................................................................................29
6.7. Lock.....................................................................................................................................................................29
6.8. Factory Reset.....................................................................................................................................................29
7. Information............................................................................................................................................................30
Remote Control ..........................................................................................................................................................31
1. Auto Mode............................................................................................................................................................32

2
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
2. Built-in Color Programs........................................................................................................................................32
3. Fade Mode ...........................................................................................................................................................32
4. DMX Address/DMX Channel Mode .................................................................................................................33
5. Economy ...............................................................................................................................................................33
DMX Channels ............................................................................................................................................................33
4 Channels ................................................................................................................................................................33
6 Channels ................................................................................................................................................................33
9 Channels ................................................................................................................................................................34
Maintenance....................................................................................................................................................................35
Replacing the Fuse (charging case)......................................................................................................................35
Troubleshooting ...............................................................................................................................................................36
No Light ........................................................................................................................................................................36
No Response to DMX.................................................................................................................................................36
Product Specifications....................................................................................................................................................37
Dimensions........................................................................................................................................................................38

3
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear to be damaged from shipping or the carton
itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
Your shipment includes:
●6 x EventLITE 4/10 Q4
●1 x charging case
●2 x remote control
●Pro power cable (1,3 m)
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual

4
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Before your initial start-up, please make sure that there is no damage caused by transportation. Should
there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never attempt lifting the device on your own. The device is heavy (40 kg). Use the included wheels
to move the device on flat surfaces. When lifting, ask at least 2 persons for assistance. Refer to the
regulations concerning safe manual handling of heavy objects.
●Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●Never remove warning or informative labels from the unit.
●Never use anything to cover the ground contact.
●Never place any material over the lens.
●Never look directly into the light source.
●Never leave any cables lying around.
●Do not connect this device to a dimmer pack.
●Do not charge the battery in a closed case or container.
●Do not switch the device on and off in short intervals, as this would reduce the device’s lifespan.
●Do not touch the device’s housing bare-handed during its operation. Allow the fixture to cool for at
least 5 minutes before handling.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Only use device indoors, avoid contact with water or other liquids.
●Only operate the fixture after having checked that the housing is firmly closed and all screws are
tightly fastened.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always allow free air space of at least 50 cm around the unit for ventilation.
●Always disconnect the charging case from power before cleaning or replacing the fuse.
●Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
●Make sure that the device is not exposed to extreme heat, moisture or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
●If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
●If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. Device must be installed out of reach of children. Never leave the unit running
unattended.
●Never attempt to bypass the thermostatic switch or fuses.
●The user is responsible for correct positioning and operating of the EventLITE.
●The manufacturer will not accept liability for damages caused by the misuse or incorrect installation
of this device.

5
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
●Repairs, servicing and electrical connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.
●WARRANTY: on batteries is only 6 months after date of purchase.
When the battery remains flat after charging/it does not function/it does not charge anymore, you
can order a new battery. The spare part number for the battery is available on request.
Operating Determinations
●This device is not designed for permanent operation. Regular operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light output and the illuminated surface must be bigger than 0,5
meter.
●In order to eliminate wear and improve the device’s lifespan, during periods of non-use, completely
disconnect from power source via breaker or by unplugging.
●The maximum ambient temperature ta = 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
●If the EventLITE is lowered from the ceiling or high joists, professional trussing systems have to be used.
●Use a clamp to mount the EventLITE, with the mounting bracket, to the trussing system.
●The EventLITE must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
●When rigging, derigging or servicing the EventLITE, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
Never attempt lifting the device on your own. The device is heavy (40 kg).
Use the included wheels to move the device on flat surfaces.
When lifting, ask at least 2 persons for assistance.
Refer to the regulations concerning safe manual handling of heavy objects.

6
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
The EventLITE can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
You endanger your own safety and the safety of others!
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!

7
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause of
the return. Be sure to properly pack fixture as any shipping damage resulting from inadequate packaging
is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that the fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period, complaints will not be handled anymore.
Complaints will only be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

8
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Description of the device
Features
The EventLITE 4/10 Q4 Set 6x consists of 6 LED-equipped wireless EventLITEs 4/10 Q4 spots, a charging case
and 2 remote controls.
EventLITE 4/10 Q4
●Wireless DMX by Wireless Solutions Sweden
●Controllable with an optional IR remote
●Eco mode for extended battery life
●Security: Kensington lock eye
●Input voltage: 100–240 V AC, 50/60 Hz
●Battery type: Lithium-ion
●Battery storage: 4,16 Ah
●Light source: 4 x 10W RGBW LEDs
●Operating time at Full On: 5 hours (at full RGBW) / 12 hours (using a single color)
●Charging time: 10 hours
●Spare battery: On request
●OLED display for easy setup
●Control Protocol: DMX512, wireless DMX512
●DMX channels: 4, 6, 9 channels
●Control modes: Built-in Programs, Manual, Auto, Master/Slave, Wireless Master/Slave, DMX, W-DMX
●Beam angle: 15°
●Dimmer: 0–100 %
●Strobe: 0–15 Hz
●Housing: Metal
●IP rating: IP54 (top) / IP20 (bottom)
●Connections: IEC Power IN, 3-pin XLR IN/OUT
●Cooling: Aluminum heatsink
●Operating Temperature: -10°C~+40°C
●Dimensions: 140 x 140 x 205 mm (LxWxH)
●Weight: 6 x 3,2 kg = 19,2 kg
Charging case
●Input voltage: 100–240 V AC, 50/60 Hz
●Power consumption: 160 W
●IP rating: IP20
●Connections: Pro power connector (Blue) IN/(Gray) OUT
●Fuse: F10AL/250V
●Dimensions: 595 x 440 x 482 mm (LxWxH)
●Weight: 21 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
44001 –Raincover for EventLITE 6/3, 7/4 and 4/10
44062 –IR remote for EventLITE 4/10 Q4
44063 –Carrying bag for 4 PCS EventLITE 4/10 Q4
44064 –Chargercase for 6 x EventLITE 4/10 Q4
50175 –W-DMX MicroBox F-1 G5 Transceiver

9
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Overview (EventLITE 4/10 Q4)
Fig. 01
01) Wireless DMX receiving antenna
02) IR remote sensor
03) 4 x 10W RGBW LEDs
04) Mounting hole for truss clamp (M10)
05) Charging indicator
Bottom (EventLITE 4/10 Q4)
Fig. 02
06) Ground/Earth connection
07) 3-pin DMX signal connector IN
08) 3-pin DMX signal connector OUT
09) 100–240 V AC IEC power connector IN
10) Tilting bracket
11) Power button ON/OFF
12) OLED display + control buttons
13) W-DMX LED indicator

10
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Overview (Charging case)
Fig. 03
14) Carrying handle
15) Wheel
16) Lock
17) Pro power connector (Blue) IN
18) Ground/earth connection
19) Pro power connector (Gray) OUT
20) Fuse F10AL/250V
21) IEC cable (20 cm)
22) Power indicator
23) Charging spot
24) Safety switch

11
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Installation
Remove all packing materials from the EventLITE 4/10 Q4 Set. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Adjusting the Tilt Angle
It is possible to adjust the tilt angle of the EventLITE.
01) Press and hold down the bracket button and tilt the EventLITE to the desired position.
Fig. 04
02) Release the bracket button to secure the EventLITE in position.
Setup and Operation
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 110 V specification product on 240 V power, or vice versa.
Charging the Built-in Battery
01) Press the power buttons (11), at the bottom of each EventLITE, to turn the power off.
02) Place the EventLITEs in the charging case.
03) Plug the IEC outlet cables (21)into the IEC inputs (09) on the EventLITEs.
04) Plug one end of the included pro power cable into the pro power input (17)on the charging case.
Plug the other end of the cable into a proper electric power supply socket. The power indicator (22)
will light red.
05) Charge the battery (up to 10 hours.)

12
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Fig. 05
Important!
●Charge only with the charging case open. If it is closed, the safety switch (24)will deactivate the
charging case.
●When charging, keep the device at least 1 meter from flames or any other heat source.
●When charging, the device may heat up. This is normal and should not affect the device’s lifespan or
performance.
●Avoid depleting the battery below 10 %.
●Do not charge for more than 24 hours.
●Recharge within 3 days of use.
●Press the power button (11) at the bottom of each EventLITE to off position, when storing for more
than 7 days.
●Store in an upright position.
Control Modes
There are 7 modes:
●Auto
●Built-in programs
●Manual
●Master/Slave
●Wireless Master/Slave
●DMX512 (4CH, 6CH, 9CH)
●Wireless DMX (W-DMX)
One EventLITE (Auto)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the EventLITE is not connected with a DMX cable and Wireless DMX is switched off, it functions
as a stand-alone device. See page 25 for more information about Auto mode.

13
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
One EventLITE (Built-in programs)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the EventLITE is not connected with a DMX cable and Wireless DMX is switched off, it functions
as a stand-alone device. See page 25 for more information about Built-in programs.
One EventLITE (Manual)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the EventLITE is not connected with a DMX cable and Wireless DMX is switched off, it functions
as a stand-alone device. See page 24 for more information about Manual mode.
Multiple EventLITEs (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the EventLITE and other devices.
The pins:
1. Earth
2. Signal (-)
3. Signal (+)
04) Link the units as shown in Fig. 06. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third and fourth unit. You can use
the same functions on the master device as described on pages 24–25 (Manual, Auto or Built-in
programs). This means that you can set your desired operation mode on the master device and all
slave devices will react the same as the master device.
Multiple EventLITEs (Master/Slave control)
Fig. 06

14
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Multiple EventLITEs (Wireless Master/Slave control)
01) Install multiple EventLITEs at the desired positions (maximum Wi-Fi distance: 250 m).
02) Unlock W-DMX on all EventLITEs (see page 24 for more information).
03) Make sure all the EventLITEs are in “slave” mode.
04) Set one EventLITE as a master.
05) On the master EventLITE, in main menu, press the UP/DOWN buttons to select 1: DMX and press the
ENTER button to enter the submenu. Go to SIGNAL and press the ENTER button in order to pair the
master with the slave EventLITEs.
06) When the blue W-DMX LED indicator (13)is blinking, the device is searching for a connection.
07) Once a connection has been established, the LED indicator (13)will light blue on all devices.
08) You can set your desired operation mode (Auto mode, Built-in programs or Manual) on the master
device and all slave devices will react the same as the master device.
Setup Example (Wireless Master/Slave control)
Fig. 07

15
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Multiple EventLITEs (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the EventLITEs and other devices.
04) Link the units as shown in Fig. 08. Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
05) Make sure the EventLITEs are in “slave” mode.
Multiple EventLITEs DMX Setup
Fig. 08

16
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Multiple EventLITEs (Wireless DMX Control)
01) Install multiple EventLITEs at the desired positions (maximum Wi-Fi distance: 250 m).
02) Make sure the EventLITEs are in “slave” mode.
03) In order for the EventLITEs to receive a wireless DMX signal properly, in main menu, press the
UP/DOWN buttons to select 1: DMX and press the ENTER button to enter the submenu.
04) Unlock W-DMX on all EventLITEs (see page 24 for more information).
05) Pair the wireless signal transmitter with multiple EventLITEs. In order to create a wireless connection,
please read the manual of your wireless signal transmitter.
06) When the blue W-DMX LED indicator (13)is blinking, the device is searching for a connection.
07) Once a connection has been established, the LED indicator (13)will light up blue.
08) Use a DMX cable to connect the transmitter to a suitable light controller.
Multiple EventLITEs Wireless DMX Control
Fig. 09

17
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Sweden 2.4GHz Wireless communication module
Communication distance:
Depending on the transmitting power or transmitter module
Test conditions:
W-DMX TRx Transmitter module, 2 dBi Antenna, transmitting power
20 dBm (100 mW)
Range indoor:
60 m (approx. through three concrete walls)
Range outdoor:
250 m
Wireless DMX Connection
The wireless receiving module “Pico G4 Receiver, 2,4GHz”, provided by Swedish WIRELESS SOLUTION, only
has a 2,4 GHz wireless signal receiving function. In order to match the wireless signal, please use the 50175
W-DMX MicroBox F-1 G5 Transceiver by WIRELESS SOLUTION. To control the status of the wireless
communication, please look at the blue LED indicator on the bottom of the fixture.
Wi-Fi Problems:
01) No connection with a transmitter.
The LED indicator (13)is OFF.
02) Searching for a connection.
The LED indicator (13)blinks quickly.
03) Connection with a transmitter, but no DMX data.
The LED indicator lights up for 900 ms and then blinks for 100 ms (the LED blinks slowly).
When the wireless DMX communication is normal, the LED indicator is always ON.
The EventLITE 4/10 Q4 cannot receive a wireless DMX signal and a DMX
cable signal at the same time.
When the device is in Auto mode, Built-in program mode or Manual mode, please ensure that the
matching 2,4 GHz wireless signal transmitter is OFF.
Connect the EventLITE to the Wireless DMX Signal Transmitter
The EventLITE cannot actively match a random wireless signal transmitter.
In order to create a wireless match, please check the manual of your wireless signal transmitter.
We advise you to use the W-DMX MicroBox F-1 G5 Transceiver (50175) by WIRELESS SOLUTION (Fig. 10).
Fig. 10
Disconnect the Event LITE From the Wireless DMX Signal Transmitter
01) Turn off/unlink the W-DMX. In order to do so, in main menu, press the UP/DOWN buttons to select
1: DMX and press the ENTER button to enter the submenu.
02) Press the UP/DOWN buttons to select SIGNAL.
03) Press the ENTER button to enter the submenu. In order to unlink the EventLITE, you have to make sure
the fixture is a slave device. See 5. Master/Slave Mode (page 26) for more information.
04) Press the UP/DOWN buttons to select CLEAR and press the ENTER button to confirm.
05) The EventLITE will now be disconnected.

18
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
●DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
●DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
●DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
●DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin.Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
●DAP Audio DMX adapter: 5-pin > 3-pin. Ordercode FLA29.
●DAP Audio DMX adapter: 3-pin > 5-pin. Ordercode FLA30.
●DAP Audio DMX Terminator 3-pin. Ordercode FLA42.
●DAP Audio DMX Terminator 5-pin. Ordercode FLA43.

19
Ordercode: 44061
EventLITE 4/10 Q4 Set 6x
The EventLITE 4/10 Q4 can be operated with a controller in control mode or without the controller in
stand-alone mode.
Control Panel
Fig. 11
A) OLED display
B) MENU button
C) ENTER button
D) UP button
E) DOWN button
DMX Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign the DMX fixture address, which is
the first channel from which the EventLITE will respond to the controller. Please note when you use the
controller, the unit has up to 9 channels.
When using multiple EventLITEs, make sure you set the DMX addresses right. Therefore, the DMX address of
the first EventLITE should be 1(001); the DMX address of the second EventLITE should be 1+9=10 (010); the
DMX address of the third EventLITE should be 10+9=19 (019), etc. Please, be sure that you do not have
any overlapping channels in order to control each EventLITE correctly. If two or more EventLITEs are
addressed similarly, they will work similarly.
Controlling: After having addressed all EventLITEs, you may now start operating these via your lighting
controller.
Note: After switching on, the EventLITE will automatically detect whether DMX 512 data is received or not.
If there is no data received at the DMX input, the problem may be:
●The XLR cable from the controller is not connected with the input of the EventLITE.
●The controller is switched off or defective, the cable or connector is defective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert a XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 5–30 seconds
When no button is pressed, the display will turn off.
You can set this time in Settings menu. See page 28.
To light up the display, you have to press the MENU, ENTER, UP or DOWN button.
Once you have pressed the button, the display will light up.