Larson Electronics RCL200-RF User manual

RCL200-RF
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 3
Wireless Remote Control Dual Beam Searchlight
Anodized Aluminum Housing
Instruction Manual
Thank you for your purchase of the Larson Electronics RCL200-RF searchlight. Please follow the steps below
in order to operate and maintain this product.
WARNING!
TO PREVENT RISK OF ELECTRICAL SHOCK DEACTIVATE/DISCONNECT POWER SUPPLY BEFORE INSTALLING,
MAINTAINING OR RELAMPING FIXTURE.
FEATURES
Powerful dual beam halogen bulb configuration gives 200,000 candlepower
Patent protected focus mechanism delivers true Spot/Flood capability
Wireless searchlight control system allowing up to 4 easy‐to‐install control stations
Infinite motion capabilities due to 8‐way touch pad directional control
Rugged anodized & painted aluminum housing for total corrosion resistance
Continuous rotation capabilities while elimination slip ring corrosion
27 degree vertical capabilities uses rugged Delrin components and heavy duty gear motor
Horizontal range of a continuous 360°
Patent protected sweep feature giving accurate and constant +/‐10° from starting location
Fast and Slow capabilities for accurate marker identification
Patent protected easy to install bayonet base with security locking mechanism
APPLICATION
A marine searchlight must be capable of performing a range of tasks from locating buoys to illuminating a
narrow channel. The new RCL‐200 has been designed to offer the best combination of beam spread (width)
and intensity (length), for both shorter and longer range (work). The RCL‐200 can also be used on medium to
larger motor homes for illuminating driveways to campsites, road signs and as a back‐up light.
PERFORMANCE DATA
RCL‐200 quotes performance data in two ways: Candle power & Lux. Candle power is a useful guide to actual
light produced. It does not however, measure the efficiency of the reflector design to project light at a target.
The most relevant comparison guide is LUX, which is the measurement of actual light available at a given
distance. In order to distinguish a reasonable level of detail, a level of one lux is generally necessary.
AUTO SWEEP
With the light on in either fast or slow mode, the light will continuously sweep the light 10 degrees each side of
the initial target spot. If the light is in fast mode, it will automatically place the unit into slow mode. Simply press
the auto sweep button again to finish the cycle. The light will return to its initial starting point and the directional
controls will become available for use again.
SPOT/FLOOD
The spot and flood buttons allow the beam configuration to change from a spot to a flood, or any beam
configuration between these two extreme limits. Simply hold one of the buttons down until you reach the
desired beam configuration. For full spot or flood, hold the spot or flood button down until it comes to a
complete stop.
WIRELESS RANGE PERFORMANCE
The RCL‐200 wireless controllers are tested in real life marine conditions. The lights are installed in both coach
roof and on the bow locations with primary controllers located in the wheel house and secondary controllers in
various other locations. The results show no loss of interference between the light and the controller
performing as required. Laboratory testing has shown no loss of performance in line of sight conditions at
100ft. Additional laboratory testing with the light and controller communicating through obstructions at 50ft has
shown no loss of performance.

RCL200-RF
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 3
VOLTAGE
AMP
DRAW
FUSE
SIZE
0’-10’ 10’-15’ 15’-25’ 25’-40’ 40’-60’
12 VDC
10
15
#14 (2.5)
#14 (2.5)
#12 (4)
#12 (4)
#10 (6)
24 VDC
7
10
#14 (2.5)
#14 (2.5)
#12 (4)
#12 (4)
#10 (6)
INSTALLATION
1. MOUNTING THE STAINLESS STEEL BAYONET MOUNTING BRACKET AND DECK SEAL
A. Select a location that allows for clear beam projection. The Searchlight base should be mounted on a
level, flat surface. Make sure the light is able to rotate 360 degrees without obstruction.
B. Use the mounting template to locate the stainless steel bayonet mounting plate and deck seal supplied.
A ¾ inch hole for the 12v supply needs to be drilled in the location also highlighted on the mounting
template. Drill 4 holes for fixing the light to the deck. Larson Electronics recommends stainless steel
mounting bolts with lock washers.
C. Mount the stainless steel mounting bracket so that the RCL‐200 name on the base is facing to the rear.
(Arrow will show forward)
D. Fasten light in place with ¼ inch screws or bolts depending on fixing method.
2. MOUNTING THE SEARCHLIGHT
A. Feed the power cables through the central holes in the bayonet base deck seal. If possible lead
the wires from the inside of the boat to minimize the amount of cable between the light and the bayonet
base fitting.
B. Place the light on the bayonet base fitting with the security locking grub screw located at 5 o’clock.
Rotate the light into the bayonet base fitting while applying reasonable pressure until the security
locking grub screw is at 6 o’clock (facing the rear).
C. Using the security locking grub screw key, lock the light in place by rotating the security locking grub
screw.
3. MOUNTING THE CONTROLLER
A. Select a location, which allows for convenient operation of the control.
B. Drill three holes (see Panel Cutout Template enclosed) for running the power supply cables and fixing
the bolts.
C. Run the power cables through hole drilled from the inside of the boat to minimize the amount of cable
between the controller and the mounting surface.
D. Fasten control using the installation kit included.
4. ELECTRICAL INSTALLATION
The searchlight & the controller(s) should be installed on independent electrical circuits. Additional controllers
(max 3 additional) can be wired independently or on the same circuit (see wiring diagrams 1&2). This is to
make the re‐learning of the main controller or the initial learning of any additional controllers a simple process
(see learning additional controllers section for info on the learning process). Consult the wire size chart (below)
for correct gauge of wire.
DANGER: REDUCE THE RISK OF ELECTRIC SHOCK
Disconnect power from the system before working on the unit to avoid personal injury, damage to the
surrounding environment and/or damage to the unit. Wiring Table
*Length of run is total length of the circuit from the power source to product and back to ground. Wire sizes listed are AWG
gauge and metric millimeters.
WIRING SCHEMATICS KEY
A SEARCHLIGHT
B CONTROLLER
C CIRCUIT BREAKER/FUSE BOX D BATTERY
E ADDITIONAL CONTROLLERS (3)

RCL200-RF
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 3
LEARNING MODE PROCEDURE
Note: The controller included with this product was initialized at the factory to communicate with the
searchlight. It is not necessary to conduct this procedure unless adding or replacing a controller.
1. Disconnect battery power to the searchlight.
2. Disconnect power to the transmitter.
3. Re‐connect power to transmitter.
4. Press and hold the “on/off”button and the left directional arrow on the controller while reconnecting
power to the searchlight. The searchlight will turn “on”within (2) seconds.
5. Code synchronization is complete.
LEARNING ADDITIONAL CONTROLLERS TO THE UNIT
The RCL‐200 can support up to (4) separate controllers. Each time a controller is added to the system, or is
replaced; all controllers require re‐initialization using the above procedure. Power to the searchlight must be
disconnected then reconnected while pressing the controllers “on/off” button for each controller added.
CLEANING OF EXTERIOR SURFACES
Recommendation for cleaning exterior surfaces is a solution of warm water and a mild detergent soap.
CAUTION Do not use cleaners that contain esters, halogenated solvents, aromatic solvents, ketones and
strong acids or bases.
CAUTION Burn Hazard. Do not touch lens when light is “on”.
SERVICE & MAINTENANCE
The RCL 200 Searchlight carries a one year warranty starting from the date of purchase. Any defects within
this first year will be handled by Larson Electronics and repaired at no charge to the customer. For service and
defects beyond the one year warranty period, please contact Larson Electronics‐Magnalight for information
and pricing on service replacement parts. Due to the complexity of this product all servicing and parts
replacement will be carried out at the factory or a recognized service center.
WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND
MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A
TRAINED AND COMPETENT ELECTRICIAN.
1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a
possible problem and should be thoroughly investigated and repaired as necessary.
2. Inspect contacts for signs of wear and replace if necessary.
3. Clean exterior surfaces making sure nameplates remain legible.
If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately!
This condition could cause serious or fatal personal injury due to electrocution and/or equipment damage.
Repair with the proper replacement part(s) before continuing service.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage being supplied to the fixture?
Is the fixture properly grounded?
These instructions may not cover all details or variations of this product for your equipment or installation
requirements. Should further information not covered by these instructions be required, please contact Larson
Electronics at 1-800-369-6671 for further assistance.
Please visit LarsonElectronics.com for Warranty and Return information.