Show Tec Booby Trap RG 43170 User manual

Booby Trap RG
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 43170
USER MANUAL
ENGLISH
V1

1
Booby Trap RG
Product code: 43170
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2021 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or for other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Booby Trap RG
Product code: 43170
Table of contents
1. Introduction..........................................................................................................................................................3
Before Using the Product ..................................................................................................................................3
Intended Use .......................................................................................................................................................3
Product Lifespan.................................................................................................................................................3
LEDs Lifespan .......................................................................................................................................................3
Text Conventions ................................................................................................................................................3
Symbols and Signal Words................................................................................................................................4
Symbols on the Information Label ..................................................................................................................4
2. Safety ....................................................................................................................................................................5
Warnings and Safety Instructions ....................................................................................................................5
Requirements for the User.................................................................................................................................7
3. Description of the Device ...................................................................................................................................8
Front View ............................................................................................................................................................8
Back View ............................................................................................................................................................8
Product Specifications ......................................................................................................................................9
Dimensions.........................................................................................................................................................10
4. Installation ..........................................................................................................................................................10
Safety Instructions for Installation ..................................................................................................................10
Personal Protective Equipment .....................................................................................................................10
Installation Site Requirements ........................................................................................................................11
Rigging ...............................................................................................................................................................11
Angle Adjustment.......................................................................................................................................12
Connecting to Power Supply.........................................................................................................................12
5. Setup ...................................................................................................................................................................13
Warnings and Precautions .............................................................................................................................13
Stand-alone Setup ...........................................................................................................................................13
6. Operation ...........................................................................................................................................................14
Safety Instructions for Operation...................................................................................................................14
Control Mode....................................................................................................................................................14
Remote Control Operation ............................................................................................................................15
Auto...............................................................................................................................................................16
Sound ............................................................................................................................................................16
Magic Ball Effect.........................................................................................................................................16
Water wave Effect .....................................................................................................................................16
UV ..................................................................................................................................................................16
Strobe............................................................................................................................................................16
7. Troubleshooting .................................................................................................................................................17
8. Maintenance .....................................................................................................................................................18
Safety Instructions for Maintenance.............................................................................................................18
Preventive Maintenance................................................................................................................................18
Basic Cleaning Instructions .......................................................................................................................18
Corrective Maintenance................................................................................................................................19
Replacing the Fuse.....................................................................................................................................19
9. Deinstallation, Transportation and Storage ....................................................................................................20
Instructions for Deinstallation..........................................................................................................................20
Instructions for Transportation ........................................................................................................................20
Storage...............................................................................................................................................................20
10. Disposal ..............................................................................................................................................................20
11. Approval.............................................................................................................................................................20

3
Booby Trap RG
Product code: 43170
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec Booby Trap RG
●Schuko to IEC (C13) power cable (1,5 m)
●IR remote control
●User manual
Fig. 01
Intended Use
This device is intended for professional use as a light effect. It is suitable only for indoor installation. This
device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment handle (05)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips

4
Booby Trap RG
Product code: 43170
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located at the backside of the
device.
The information label contains the following symbols:
This device is designed for indoor use.
This device shall not be treated as household waste.
This device falls under IEC protection class I.
Minimum distance from lighted objects.

5
Booby Trap RG
Product code: 43170
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
●Do not open the device or remove any covers.
●Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened.
●Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class I.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
socket-outlet with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●For replacement use fuses of the same type and rating only.
●Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.
●Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.
●Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.

6
Booby Trap RG
Product code: 43170
WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at
strobe lights.
Attention
Power supply
●Before connecting the device to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the
required power consumption of the device.
Attention
General safety
●Do not insert objects into the air vents.
●Do not connect the device to a dimmer pack.
●Do not switch the device on and off in short intervals. This decreases the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
For professional use only
This device shall be used only for the purposes it is designed for.
This device is designed to be used as a professional stage light effect. Any incorrect use may lead to
hazardous situations and result in injuries and material damage.
●This device is not suitable for households and for general lighting.
●This device is not designed for permanent operation.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.

7
Booby Trap RG
Product code: 43170
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The power cables are not damaged and do not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

8
Booby Trap RG
Product code: 43170
3. Description of the Device
The Showtec Booby Trap RG is a compact 5-in-1 effect light for creating Water Wave, UV, Strobe, Laser
and Disco Star light effects, suitable for small indoor venues. The water-wave effect has a 5 W RGB
lightsource output for vivid colours and sharp beams. The 4 LEDs at the front of the Booby Trap RG can
act both as white strobe or UV wash. The laser can provide rich and dynamic patterns in red and green.
The Booby Trap RG is controlled by DMX and IR remote in either Auto run, Sound-controlled and
Master/Slave mode. An infrared remote and power cable are included.
Front View
Fig. 02
01) Water effect
02) 4 LEDs for white strobe or UV wash effect
03) Infrared sensor
04) Laser
05) Magic Ball effect
06) Mounting bracket
07) 2x Adjustment screw
Back View
Fig. 03
08) ON / OFF
09) IEC (C14) power connector + Fuse T 1,6 A, 250 V

9
Booby Trap RG
Product code: 43170
Product Specifications
Model:
Booby Trap RG
Electrical:
Input voltage:
100–240 V AC, 50/60 Hz
Power consumption:
20 W
Fuse:
T 1,6 A, 250 V
Physical:
Dimensions:
276 x 171 x 157 mm (L x W x H)
Weight:
1,6 kg
Optics:
Light source water effect:
5 W 3-in-1 RGB LED
Strobe:
0–20 Hz
Operation and control:
Control:
Stand-alone (auto, sound-controlled)
Control panel:
Remote control
Connections:
Power connections:
IEC (C14) power connector IN
Construction:
Housing:
Extruded aluminum and metal plate
Color:
Black
IP rating:
IP20
Cooling:
Aluminum heatsink
Thermal:
Maximum ambient temperature ta:
40 °C
Minimum operating temperature:
-10 °C
Minimum distance:
Minimum distance from flammable surfaces:
0,5 m
Minimum distance to lighted object:
0,5 m

10
Booby Trap RG
Product code: 43170
Dimensions
Fig. 04
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.

11
Booby Trap RG
Product code: 43170
Installation Site Requirements
●The device can be used only indoors.
●The device can be mounted to a truss or other rigging structure.
●The minimum distance to other objects must be bigger than 0,5 m.
●The minimum distance between the light output and the illuminated surface must be bigger than
0,5 m.
●The maximum ambient temperature ta= 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure. Make sure
that all loads are within the pre-determined limits of the supporting structure.
CAUTION
Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below:
01) Use a clamp to attach the device to the supporting structure, as shown in Fig. 07. Make sure that the
device cannot move freely.
02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the
secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable around the mounting bracket (06), as shown in Fig. 05.
Fig. 05

12
Booby Trap RG
Product code: 43170
Angle Adjustment
You can adjust the angle of the device with the 2 adjustment screws (07).
01) Turn the adjustment screws (07) counterclockwise to release them.
02) Tilt the device at the desired angle (see Fig. 08).
03) Turn the adjustment screws (07) clockwise to tighten them. Make sure that the device cannot move
freely after the adjustment screws (07) are tightened.
Fig. 06
Connecting to Power Supply
DANGER
Electric shock caused by short-circuit
The device accepts AC mains power at 100–240 V and 50/60 Hz. Do not supply power at any other
voltage or frequency to the device.
This device falls under IEC protection class I. Make sure that the device is always electrically connected
to the ground (earth).
Before connecting the device to the socket-outlet:
●Make sure that the power supply matches the input voltage specified on the information label on
the device.
●Make sure that the socket-outlet has ground (earth) connection.
Connect the device to the socket-outlet with the power plug. Do not connect the device to a dimmer
circuit, as this may damage the device.

13
Booby Trap RG
Product code: 43170
5. Setup
Warnings and Precautions
Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.
Stand-alone Setup
The Booby Trap RG can be operated manually, in auto mode or in sound-controlled mode.
For more information about the control modes, refer to 6.2. Control Modes on page 14.

14
Booby Trap RG
Product code: 43170
6. Operation
Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is intended for professional use as a light effect. It is suitable only for indoor installation. This
device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.
Control Mode
The Booby Trap RG can only be operated as a stand-alone device.
●Stand-alone: Auto operation mode (auto program, built-in chases, color presets), manual
operation mode, sound-controlled operation mode (auto program)

15
Booby Trap RG
Product code: 43170
Remote Control Operation
The device can be operated with an IR remote control. The remote control is included in the delivery.
DANGER
Do not ingest battery, chemical burn hazard.
The remote control contains a coin cell battery. If the coin cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
The battery is already installed in the remote control. It is protected against discharge by a transparent
plastic foil. Remove the plastic foil before using the remote control for the first time.
When replacing the battery, make sure that the polarity is correct. Incorrect polarity may damage the
remote control.
To operate the device with the IR remote control:
Point the remote control to the IR sensor.
Button
Name
ON/OFF
Auto
Sound
Magic Ball Effect
Water Wave Effect
UV
White Strobe Effect
Increase/decrease motor
speed
Increase/decrease strobe
speed
Increase/decrease sound
sensitivity
Fig. 7
Press the ON/OFF button to turn the LEDs on.
Press the ON/OFF button again to turn the LEDs off.

16
Booby Trap RG
Product code: 43170
Auto
Press the Auto button to start the auto program. Press the Motor buttons to increase/decrease the
speed of the auto program.
Sound
Press the Sound button to start the auto program. Press the Sensitivity buttons to increase/decrease
the speed of the sound program.
Magic Ball Effect
Press the LED button to enter Magic Ball mode (05). The device will run one of the 7 built-in auto
programs. Only program 7 has a built-in strobe program.
Program 1
Program 2
Program 3
Program 4
Program 5
Program 6
Program 7
R
G
B
RGB
RG-GB-BR-
RGB
R-G-B-RG-
GB-BR-RGB
R-G-B-RG-
GB-BR-RGB
Water wave Effect
Press the LS button to enter Water wave mode (01). The device will run one of the 9 built-in auto
programs. Only program 8 has a built-in strobe program. Program 9 is a color fade program.
Program
1
Program
2
Program
3
Program
4
Program
5
Program
6
Program
7
Program
8
Program
9
R
G
B
W
R-G-B-W
RGB-RG-
GB-BW-
WR-
RGBW-
RGW-
GBW-
BRW
R-G-B-W-
RGB-RG-
GB-BW-
WR-
RGBW-
RGW-
GBW-
BRW
R-G-B-W-
RGB-RG-
GB-BW-
WR-
RGBW-
RGW-
GBW-
BRW
R-G-B-W
UV
Press the UV button to activate UV color macro.
Strobe
Press the Flash button to activate Strobe mode. Press the Speed buttons to increase/decrease the
speed of the strobe from 1 - 8. By pressing the button 9 times, the strobe will be off.

17
Booby Trap RG
Product code: 43170
7. Troubleshooting
This troubleshooting guide contains solutions to problems which can be carried out by an ordinary
person. The device does not contain user-serviceable parts.
Unauthorized modifications to the device will render the warranty void. Such modifications may result in
injuries and material damage.
Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the
solution is not described in the table.
Problem
Probable cause(s)
Solution
The device does not
function at all
No power to the device
●Check if power is switched on and
cables are plugged in
Main fuse is blown
●Replace the fuse. See 8.3.1. Replacing
the Fuse on page 19
No light or LEDs cut
out intermittently
LEDs are damaged
●Disconnect the device and contact
your Highlite International dealer
The power supply settings do not
match local AC voltage and
frequency
●Disconnect the device. Check the
settings and correct, if necessary

18
Booby Trap RG
Product code: 43170
8. Maintenance
Safety Instructions for Maintenance
DANGER
Electric shock caused by dangerous voltage inside
Disconnect power supply before servicing or cleaning.
Preventive Maintenance
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The power cables are not damaged and do not show any material fatigue.
Basic Cleaning Instructions
The external lens of the device must be cleaned periodically in order to optimize the light output. The
cleaning schedule depends on the conditions at the site where the device is installed. When smoke or
fog machines are used at the site, the device will need more frequent cleaning. On the other hand, if the
device is installed in well-ventilated area, it will need less frequent cleaning. To establish a cleaning
schedule, examine the device at regular intervals during the first 100 hours of operation.
To clean the device, follow the steps below:
Disconnect the device from the electrical power supply.
Allow the device to cool down for at least 15 minutes.
03) Remove the dust collected on the external surface with dry compressed air and a soft brush.
04) Clean the lens with a damp cloth. Use a mild detergent solution.
05) Dry the lens carefully with a lint-free cloth.
06) Clean the DMX and other connections with a damp cloth.
Attention
●Do not immerse the device in liquid.
●Do not use alcohol or solvents.
●Make sure that the connections are fully dry before connecting the device to the power supply and
to other devices.

19
Booby Trap RG
Product code: 43170
Corrective Maintenance
The device does not contain user-serviceable parts. Do not open the device and do not modify the
device.
Refer repairs and servicing to instructed or skilled persons. Contact your Highlite International dealer for
more information.
Replacing the Fuse
DANGER
Electric shock caused by short-circuit
●Do not bypass the thermostatic switch or fuses.
●For replacement use fuses of the same type and rating only.
Power surges, short-circuit or incorrect electrical power supply may cause a fuse to burn out. If the fuse
burns out, the device will not function anymore. If this happens, follow the steps below:
01) Disconnect the device from the electrical power supply.
02) Allow the device to cool down for at least 15 minutes.
03) Pry up the integrated fuse holder with a flat-blade screwdriver.
04) If the fuse is brown or unclear, it is burned out. Remove the old fuse.
05) Insert a new fuse in the fuse holder. Make sure that the type and the rating of the replacement fuse
are the same as the ones specified on the information label of the product.
06) Replace the integrated fuse holder in the opening and push it gently back in its place.