Show Tec Event Bar 2 CCT User manual

Event Bar 2 CCT
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 44120
USER MANUAL
ENGLISH
V1

10
Event Bar 2 CCT
Product code: 44120
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2021 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or for other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

11
Event Bar 2 CCT
Product code: 44120
Table of contents
1. Introduction........................................................................................................................................................12
Before Using the Product ................................................................................................................................12
Intended Use .....................................................................................................................................................12
Product Lifespan...............................................................................................................................................12
LEDs Lifespan .....................................................................................................................................................12
Text Conventions ..............................................................................................................................................13
Symbols and Signal Words..............................................................................................................................13
Symbols on the Information Label ................................................................................................................13
2. Safety ..................................................................................................................................................................14
Warnings and Safety Instructions ..................................................................................................................14
Requirements for the User...............................................................................................................................16
3. Description of the Device .................................................................................................................................17
Front View ..........................................................................................................................................................17
Back View ..........................................................................................................................................................18
Bottom View......................................................................................................................................................18
Product Specifications ....................................................................................................................................19
Dimensions.........................................................................................................................................................20
4. Installation ..........................................................................................................................................................21
Safety Instructions for Installation ..................................................................................................................21
Personal Protective Equipment .....................................................................................................................21
Installation Site Requirements ........................................................................................................................21
Mounting Options.............................................................................................................................................21
Diffuser Installation ...........................................................................................................................................24
Charging the Battery.......................................................................................................................................25
5. Setup ...................................................................................................................................................................25
Stand-alone Setup ...........................................................................................................................................25
6. Operation ...........................................................................................................................................................25
Safety Instructions for Operation...................................................................................................................25
Turning On/Off ..................................................................................................................................................26
Control Modes ..................................................................................................................................................26
Manual Control.................................................................................................................................................26
Maximum Output Mode ...........................................................................................................................26
Economical Mode......................................................................................................................................26
Remote Control ................................................................................................................................................27
Maximum Output Mode ...........................................................................................................................28
Economical Mode......................................................................................................................................28
7. Troubleshooting .................................................................................................................................................29
8. Maintenance .....................................................................................................................................................29
Preventive Maintenance................................................................................................................................29
Basic Cleaning Instructions .......................................................................................................................29
Corrective Maintenance................................................................................................................................30
9. Deinstallation, Transportation and Storage ....................................................................................................30
Instructions for Deinstallation..........................................................................................................................30
Instructions for Transportation ........................................................................................................................30
Storage...............................................................................................................................................................30
10. Disposal ..............................................................................................................................................................31
11. Approval.............................................................................................................................................................31

12
Event Bar 2 CCT
Product code: 44120
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec Event Bar 2 CCT
●AC power adapter 15 V DC
●2 x 25° diffuser
●2 x retainer spring
●Carrying bag
●Remote control
●User manual
Fig. 01
Intended Use
This device is designed to be used as a battery LED bar suitable for stage lighting, corporate and private
events. This device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Do not switch on and off the device in short
intervals. This will reduce the wear and will improve the device’s lifespan.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.

13
Event Bar 2 CCT
Product code: 44120
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons and interface sliders and fields are in bold lettering, for example “Slide
the Strobe slider”, “Enter the DMX starting address in the Address field”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “set the power switch (14) to on position”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located on the backside of the
device.
The information label contains the following symbols:
This device shall not be treated as household waste.
This device is designed for indoor use.
Read and observe the instructions in the user manual.

14
Event Bar 2 CCT
Product code: 44120
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Risk of explosion caused by incorrect handling
This device contains a built-in rechargeable lithium-ion battery. The battery is not replaceable. The
battery may explode or cause burns if it is crushed, disassembled or exposed to fire or high temperatures.
●Do not open the device and do not attempt to remove the built-in battery.
●Do not disassemble the battery.
●Do not crush or puncture the battery.
●Do not short-circuit the battery.
●Do not expose the battery to water or other liquids.
●Keep the battery away from fire and heat.
DANGER
Electric shock caused by short-circuit
This device is delivered with an AC power adapter. Incorrect handling of the AC power adapter may
result in hazardous situations.
●Use only the AC power adapter delivered with the device.
●Do not wrap the power cable around the power adapter or any other object. This can damage the
internal wires.
●Do not cover the power adapter with anything when it is plugged into the socket-outlet. This may
cause overheating.
●Do not expose the power adapter to water or other liquids.
Do not use the power adapter:
●If it shows signs of overheating, for example the plastic is damaged.
●If the AC input pins show signs of corrosion or overheating.
●If the power cable is damaged or shows signs of material fatigue.

15
Event Bar 2 CCT
Product code: 44120
Attention
Power supply
Before connecting the AC power adapter to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the AC
power adapter.
Attention
General safety
●Do not switch the device on and off in short intervals. This decreases the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
This device shall be used only for the purposes it is designed for.
This device is designed to be used as a battery LED bar suitable for stage lighting, corporate and private
events. This device is not suitable for households and for general lighting.
Any incorrect use may lead to hazardous situations and result in injuries and material damage.
●This device is not suitable for households and for general lighting.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.

16
Event Bar 2 CCT
Product code: 44120
Requirements for the User
This product may be used by ordinary persons. Maintenance and installation may be carried by ordinary
persons. Service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

17
Event Bar 2 CCT
Product code: 44120
3. Description of the Device
The Showtec Event Bar 2 CCT is designed to be used as a battery LED bar suitable for stage lighting,
corporate and private events. The Event Bar 2 CCT can be controlled manually or with a remote control.
Front View
Fig. 02
2 x 20 W White LED
2 threaded openings, M10
Magnet
Slot for Velcro
Safety eye
2 x spigot for the WENTEX® Pipes & Drapes (Ø 15 mm)

18
Event Bar 2 CCT
Product code: 44120
Back View
Fig. 03
Power switch ON/OFF
Charged LED indicator (green)
Charging LED indicator (red)
DC connector, 15 V DC
Bottom View
Fig. 04
CCT button
Output button
Mode button
Output level LED indicators
Infrared sensor

19
Event Bar 2 CCT
Product code: 44120
Product Specifications
Model:
Event Bar 2 CCT
Electrical:
Input voltage:
15 V DC
Power consumption:
50 W
Physical:
Dimensions:
320 x 95 x 147 mm (L x W x H)
Weight:
1,4 kg
Optics:
Light source:
2 x 20 W White LED
Luminous flux:
550 lm
CCT:
3000–6000 K
Beam angle:
10° (25° diffusers included)
Operation and control:
Control:
Manual, IR remote
Display:
No
AC power adapter:
Input voltage:
100–240 V AC, 50/60 Hz
Input current:
1,2 A
Output voltage:
15 V DC
Output current:
2,4 A
Battery:
Type:
Sealed lithium-ion battery
Capacity:
5200 mA∙h
Voltage:
12,6 V
Watt-hour rating:
57,72 W∙h
Runtime:
3 hours (highest output) / 8 hours (lowest output)
Charge time:
6 hours
Battery lifetime:
400 discharge cycles (battery runtime drops at 70 %)
Construction:
Housing:
Aluminum
Color:
Black
IP rating:
IP20
Cooling:
Convection
Thermal:
Ambient temperature ta:
40 °C
Maximum housing temperature tc:
70 °C
Minimum distance:
Minimum distance to lighted object:
0,5 m

20
Event Bar 2 CCT
Product code: 44120
Dimensions
Fig. 05

21
Event Bar 2 CCT
Product code: 44120
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.
Installation Site Requirements
●The device can be used only indoors.
●The device can be mounted to a truss or other rigging structure in any orientation.
●The minimum distance to other objects must be bigger than 0,5 m.
●The minimum distance between the light output and the illuminated surface must be bigger than
0,5 m.
●The maximum ambient temperature ta = 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.
Note:
It is recommended to charge the device at an ambient temperature between 0 °C and 35 °C.
Mounting Options
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any
orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
If the device is mounted overhead, it should always be secured with a safety cable or another
secondary suspension.
WARNING
Do not mount the device only by the magnet above people’s heads.
The secondary suspension can be attached on the safety eye (05). The device is equipped with 2
threaded openings (02)for M10 screws where you can attach clamps.

22
Event Bar 2 CCT
Product code: 44120
The mounting options are as follows:
Option 1: installation on a rigging structure with
clamps
Use 2 clamps to attach the device to the
supporting structure, as shown in Fig. 06.
Secure the device with a secondary
suspension, for example a safety cable.
Make sure that the secondary suspension
can hold 10 times the weight of the device.
Put the safety cable through the safety eye
(05).
Fig. 06
Option 2: installation with the magnet on a metal
surface
Attach the device to a flat metal surface, as
shown in Fig. 07. The built-in magnet (03) will hold
the device in position.
Note:
If the device is mounted overhead, it should
always be secured with a safety cable or another
secondary suspension. Make sure that the
secondary suspension can hold 10 times the
weight of the device. Put the safety cable
through the safety eye (05).
Do not mount the device only with the magnet.
Fig. 07
Option 3: installation with a Velcro fastener
Use the Velcro snap fasteners to attach the
device to the supporting structure, as shown in
Fig. 08.
Fig. 08

23
Event Bar 2 CCT
Product code: 44120
Option 4: installation on the WENTEX® Pipes & Drapes system
Press and hold down the button on the WENTEX® telescopic upright (Fig. 09).
Put the spigots (06) into the openings on the WENTEX® telescopic upright (Fig. 09).
Release the button on the WENTEX® telescopic upright to secure the device (Fig. 10).
Note:
The WENTEX® Pipes & Drapes system is not included in the delivery. You can purchase it with any Highlite
International dealer.
Fig. 09
Fig. 10

24
Event Bar 2 CCT
Product code: 44120
Diffuser Installation
The Event Bar 2 CCT is delivered with 2 diffusers: 25°.
To install the diffuser, follow the steps below:
Put the diffuser on the lens.
Gently press the retainer spring as flat as possible and insert it against the diffuser (see Fig. 11).
Release the retainer spring. The retainer spring will now snap into position.
Fig. 11

25
Event Bar 2 CCT
Product code: 44120
Charging the Battery
DANGER
Risk of explosion caused by incorrect handling
This device contains a built-in rechargeable lithium-ion battery. The battery is not replaceable. The
battery may explode or cause burns if it is crushed, disassembled or exposed to fire or high temperatures.
●Do not open the device and do not attempt to remove the built-in battery.
This device is delivered with an AC power adapter that is used to charge the battery. Before connecting
the AC power adapter to the socket-outlet, make sure that the power supply matches the input voltage
specified on the information label on the AC power adapter.
To charge the battery follow the steps bellow:
Turn off the device with the power switch (07).
Connect the AC power adapter to the device. Use only the AC power adapter delivered with the
device.
Connect the AC power adapter to the socket-outlet.
During charging, the Charging LED indicator (09) is red. When charging is completed, the Charged LED
indicator (08) lights green.
●Charge the battery before using the device for the first time.
●Do not deep discharge the battery as this will shorten the battery’s lifetime. Recharge the battery as
early as possible. Do not let the light run until the battery is depleted.
●Make sure that the battery is charged to at least 50 % before storing the device.
It is recommended to charge the device at an ambient temperature between 0 °C and 35 °C.
If the device is charged in a carrying bag, leave the case open.
Refer to 3.4. Product Specifications on page 19 for the charge time of the battery.
5. Setup
Stand-alone Setup
The Event Bar 2 CCT functions as a stand-alone device. It can be operated manually or with an infrared
(IR) remote control. For more information about the control modes, refer to 6.3. Control Modes on page
26.
6. Operation
Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is designed to be used as a battery LED bar suitable for stage lighting, corporate and private
events. This device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.

26
Event Bar 2 CCT
Product code: 44120
Turning On/Off
The device has a power switch.
●Set the power switch (07)to ON position to turn on the device.
●Set the power switch (07)to OFF position to turn off the device.
Make sure that the device is turned off with the power switch (07)when the device is not in use. This will
prevent the battery from depletion.
Control Modes
The Event Bar 2 CCT supports the following control modes:
●Maximum Output mode
●Economical mode
To operate the device:
●Press the control buttons on the device to adjust the operation mode, color temperature and the
intensity. See 6.4. Manual Control on page 26 for more information.
●Press the buttons on the remote control to adjust the operation mode, color temperature and the
intensity. See 6.5. Remote Control on page 27 for more information.
Manual Control
The device can be controlled via the control buttons (11/12/13).
Press the mode button (13) to toggle the operation modes (Maximum Output mode/Economical mode).
Note:
When you turn off the device, the next time you turn it on, it will continue to operate in the previously
selected operation mode.
Maximum Output Mode
In this operation mode the device operates at the maximum output level. You can set the color
temperature.
Repeatedly press the CCT button (11) to select one of the 4 color temperature options: 3000 K, 4200 K,
5600 K or 6000 K.
Economical Mode
In this operation mode you can manually set the device’s output level, in order to save the battery’s
lifespan, as well as the color temperature. The device’s output level will drop every hour. First, it will drop
to 85 %, then to 75 %, 60 %, etc.
Repeatedly press the CCT button (11) to select one of the 4 color temperature options: 3000 K, 4200
K, 5600 K or 6000 K.
Repeatedly press the output button (12) to select one of the 6 output level options: 30 %, 45 %, 60 %,
75 %, 85 % or 100 %. Observe the output level LED indicators (14) to select the desired option.

27
Event Bar 2 CCT
Product code: 44120
Remote Control
The device can be controlled with an IR remote control.
DANGER
Do not ingest battery, chemical burn hazard
The remote control contains a coin cell battery. If the coin cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
The battery is already installed in the remote control. It is protected against discharge by a transparent
plastic foil. Remove the plastic foil before using the remote control for the first time.
When replacing the battery, make sure that the polarity is correct. Incorrect polarity may damage the
remote control.
You can control several devices at the same time with the remote control. Make sure that you point the
remote control to the infrared sensor (15)of the device or group of devices that you want to control, as
shown in Fig. 12. If you point the remote control to the infrared sensor (15)of the device outside of the
range of the sensor, the device will not respond to the remote control (Fig. 13).
Fig. 12
Fig. 13

28
Event Bar 2 CCT
Product code: 44120
To operate the device with the IR remote control, point the remote control to the infrared sensor (15).
The remote control has the following functions:
Fig. 14
Button
Name
Button
Name
ON/OFF
A
Auto
No function
No function
No function
Minus
No function
No function
No function
Plus
No function
Press the Auto button to toggle the operation modes (Maximum Output mode/Economical mode).
Note:
When you turn off the device, the next time you turn it on, it will continue to operate in the previously
selected operation mode.
Maximum Output Mode
In this operation mode the device operates at the maximum output level. You can set the color
temperature.
Repeatedly press the A button to select one of the 4 color temperature options: 3000 K, 4200 K, 5600 K or
6000 K.
Economical Mode
In this operation mode you can manually set the device’s output level, in order to save the battery’s
lifespan, as well as the color temperature. The device’s output level will drop every hour. First, it will drop
to 85 %, then to 75 %, 60 %, etc.
Repeatedly press the A button to select one of the 4 color temperature options: 3000 K, 4200 K,
5600 K or 6000 K.
Repeatedly press the minus or plus button to select one of the 6 output level options: 30 %, 45 %,
60 %, 75 %, 85 % or 100 %. Observe the output level LED indicators (14) to select the desired option.