LEGRAND DLI90BTWE User manual

HPM Smart LED Downlight
Instruction Sheet
Cat.No. DLI90BTWE, REMOTEBTDL
1 Specifications
Cat. No. DLI90BTWE
Fascia Colour White
Nominal Supply Voltage 230 - 240 V a.c. 50 Hz
Lumen Range
3000K - 690 lm
to
5000K - 710 lm
Colour Temperature Range 3000 K (Warm White) to 5000 K (Natural White)
(Changeable through App only)
Input Power 6.5 W
Power Factor 0.5
Standby Power 0.5 W
Surge Rating 2500 V
Efficacy 113 lm/W Max.
Ripple Frequency Resistant Yes
Colour Rendering Index (CRI) 80+
Beam Angle 100°
Ceiling Cut-out Size Ø 90 mm
Fascia Size Ø 110 mm
Depth into Ceiling 70 mm
Lifespan (@25°C ambient free air) 35,000 hrs
Dimming Dimmable with HPM Connect App and Remote Control
(Not compatible with external dimmer)
Dimming Range 5% to 100%
Max. No of device per Mesh 128 max
Range for Individual Lamp
20 m (Indoors)
This range may be reduced by obstruction like a brick /
concrete wall.
IP Rating IP44 (Front Face)
Warranty 3 Years
Cat. No. REMOTEBTDL
(Remote is sold separately)
Features
■Max.100 Downlights per Remote Control
■2 x AAA Batteries (Not Included)
■Wall fixing Bracket included.
Functions
■Switch ON/OFF
■Dimming (20% increments and 20%
minimum)
Class II construction
Dimmable through App
and Remote Control
IC - 4 Insulation Rating
IC - F Insulation Rating
Please read carefully: Read through these instructions completely before commencing installation. Retain for future use. This product should
be installed by a licensed electrical contractor or similarly qualified person.
Control via HPM Connect App
and Remote Control
ON OFF
90mm
110mm
70mm
10mm
APP
!

1. Ensure your device is connected to the internet to follow all the steps.
2. Download the HPM Connect App on your device. You can directly go to the store (App Store or Google Play) or scan the QR code given below, which
will automatically take you to the download page.
3. Open the HPM Connect App. For new user, sign up for a new account and for an existing user, log-in with your username and password. You can
use your email address to register. Verification code will be sent through via an email. Set password, then proceed to open App.
4. Pair your Downlight / Remote Control through Auto scan or add Manually. For Remote Control pairing: Enable networking mode on Remote by
pressing both ON & OFF buttons simultaneously for 5 seconds until the indicator on remote starts to flash. To Reset existing downlight: First
power ON the downlight then switch ON/OFF 5 times (OFF period should be 1-2 seconds). Then the downlight should starts blinking. If the light does
not blink and stays ON, repeat the process.
5. Once the HPM Connect App pairs with the Downlight / Remote Control, you can control the downlight with your device or the Remote Control (Optional).
6. For detailed instructions on how to use the HPM Connect App on your smart device follow the link below or scan the given QR code in section 3.
www.hpm.com.au/product/smart-downlight
Warranty
Legrand warrants this product for a period of 3 years from the date of purchase.
These goods come with guarantees that cannot be excluded under the Australian
and New Zealand Consumer Laws. You are entitled to a replacement or a refund
for a major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
See the Warranty card enclosed with this product for further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
LE11479AC 09/20201
Pairing the Downlight / Remote control using HPM Connect App
Legrand Australia
1300 369 777
www.hpm.com.au
Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
1. This product must be installed and used as per these instructions. 2. Ensure power is disconnected from 240 V supply wiring before connecting mains
cable. 3. An IP rating of IP44 is generally considered suitable for external walls with supplementary protection such as overhanging eaves. 4. The IP
rating of this product is only valid when installed on a flat and non-porous surface. Additional sealing may be required for irregular surfaces. 5. This
product contains no serviceable parts and no attempt should be made to repair this product. If the product is faulty it should be discarded. 6. This
product is not, suitable for installation in hazardous and/or corrosive areas. 7. Electrical installations periodically receive transient over voltages. This
product has been designed to minimise the effect of such voltages on connected equipment. It may not give full protection for extreme over-voltage
transients such as those resulting from a close lightning strike. 8. This product has been designed to operate in ambient temperatures: -5°C to 25°C,
occasionally reaching 35°C. 9. The material in this product may vary in colour from batch to batch. Colour matching from one batch to another cannot
be guaranteed. 10. It is recommended to install a wall switch per circuit/per room during installation. 11. To use all functions of this HPM Smart
Downlight it is required to have a compatible iOS or Android device installed with HPM Connect App. 12. This product utilises intellectual property in the
form of registered designs, trademarks, and/or patents. Such intellectual property remains the property of Legrand in all cases. 13. Legrand reserves
the right to modify the specification of this product at any time. 14. The privacy policy is available on App store / Play store.
2
Instructions
3
Please make sure that the Downlight is installed as per instructions. Before pairing,
■ Check the Downlight is powered ON and turn ON the Bluetooth of the smart device.
■ Have working Remote Control (Optional).
Paper
Note: ● One Remote control can operate up to 100 lamps, and one HPM smart downlight can be controlled by up to 8 Remote Control units.
●Unpairing can also be done by deleting Remote Control from HPM Connect App.
● If only one smart downlight is installed, it can only be operated by one paired smart device at a time. To operate using multiple smart
devices you must have multiple smart products.
Please note that the terms used in this instruction sheet are trademarks.
1. The Bluetooth word is registered trademark owned by Bluetooth SIG, Inc. 2. iOS is a trademark or registered trademark of Cisco. 3. Android is a
trademark of Google, Inc.
Scan the QR code given below, which takes you to our website for detailed instructions on how to install the downlights and instructions on how to use the
HPM Connect App.
Product Notes