Stoane Lighting 50mm ADL CP.X User manual

Mike Stoane Lighting Ltd
20 Dryden Road Bilston Glen Ind Est.
Loanhead Midlothian EH20 9LZ UK
T: [phone]
F: [phone]
[email protected]
www.mikestoanelighting.com
VAT No GB682885284
Limited Company 188910
50mm ADL CP.X
Installation and Maintenance
Instructions
IMPORTANT: All wiring connections must be made before switching on mains power.
European Conformity
Please retain these instructions for future reference
This product should not be disposed of in your general waste
Not suitable for covering with thermally insulating material
Class III - Extra Low Voltage
Indoor Use Only
IP20
Xicato LED Module
50mm ADL CP X.pdf 1 11/12/2019 12:49:26

Electrical Supply
Installation must be carried out by a qualified electrician in
accordance with BS 7671:2008 Wiring Regulations.
230/240V AC 50/60Hz mains supply to a suitable SELV
LED Driver.
Site conditions: LED equipment is more susceptible to
static damage and overvoltage than previous technology.
Before handling or connecting to the mains supply ensure
that all MSL products are protected from static discharge
and that the mains supply is to regulation. (230V +10
-6%)
This fitting is supplied with a Xicato LED module. Refer to
the fitting label for the module version and wattage. More
information on the module can be found at
www.xicato.com/support
Mains cables must be double insulated, strain relieved
and separated from E.L.V output cables.
If using the Xicato XTM Module;
This unit requires a constant current driver. 700mA Max.
If using the Xicato XIM Module;
This unit requires a 48V constant voltage driver.
Observe polarity:
Positive (+) is marked as RED.
Incorrect supply or reverse polarity can cause irreparable
damage.
All connections must be made before switching on mains.
If the supply is energised prior to making the connections
to the fitting then the resulting surge will damage the LED.
All lighting equipment is delicate and easily damaged
through misuse or inappropriate installation (mechanical
or electrical). Repairs and replacements may cause
delays and will be chargeable. Contact MSL for support if
required. For full warranty terms & conditions please visit
our website.
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
The entire dimming control circuit source must be of
SELV insulation class.
Installation
Check that the mounting surface is suitable for the
installation of this fitting.
A 92mm diameter hole is required for mounting.
Step 1 Make mains connections to SELV LED driver
and extra low voltage connections to the
fitting.
Step 2 Insert the fitting into the cut-out.
Step 3 Tightening the 2 CSK fixings will swing the
ceiling tabs out and secure the fitting in place.
Step 4 Fit the coverplate.
Ensure that the installation of this fitting does not
compromise any fire barrier offered by your ceiling.
Intumescent downlighter fire hoods should be used to
maintain the integrity of the barrier in the event of a
fire.
Do not cover the luminaire with insulation. Heat sinks
and fan assisted lamps must be kept free from dust
and well ventilated to ensure long term reliability and
light quality.
WARNING: Do not look at exposed LED lamps in
operation. Eye injury can result.
Cleaning:
Fully isolate the fitting and allow to cool.
Clean the fitting with a slightly damp lint free cloth
from a mild solution of soap and water. The fitting
must be completely dry before reconnecting power.
Incompatible or abrasive chemicals can damage the
fitting, contact MSL for advice if required.
50mm ADL CP X.pdf 2 11/12/2019 12:49:26

23
4
To Fit the Cover Plate
Centrally locate the cover plate onto the bezel
aligning the slot with the flats on the ADL bezel.
Rotate 90° clockwise to secure.
To Remove the Cover Plate
Rotate 90°
Use a screwdriver or similar in the slot to prise off
the plate (Use caution, do not damage the paint)
Slot
90°
Pan & Tilt locking
Tightening the installation
screws will swing out the tabs
which clamp ceiling surface
from behind, retaining the
fitting.
To LED driver
Ø92mm cut out
50mm ADL CP X.pdf 3 11/12/2019 12:49:26

Optic
Accessories
Circlip
MODULE AND ACCESSORIES
The fitting uses a Xicato LED module. The colour
temperature, drive current and lumen output can be
found on the product label on the fitting.
To Add/Remove accessories:
Isolate the fitting from the supply and allow to cool.
Step 1 Remove the circlip and any accessories.
Step 2 Remove the optic.
Step 3 Replace optic and accessories as required
and secure with circlip.
50mm ADL CP X.pdf 4 11/12/2019 12:49:26