Show Tec EventLITE 4/8 Mini Q4 V1 User manual

EventLITE 4/8 Mini Q4
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 44080
USER MANUAL
ENGLISH
V1

1
EventLITE 4/8 Mini Q4
Product code: 44080
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Installation and operation of the device
●Intended and non-intended use of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2023 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document or other language versions, please visit our website
www.highlite.com or contact us at [e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
EventLITE 4/8 Mini Q4
Product code: 44080
Table of contents
1. Introduction..........................................................................................................................................................4
Before Using the Product ..................................................................................................................................4
Intended Use .......................................................................................................................................................4
Product Lifespan.................................................................................................................................................4
LEDs Lifespan .......................................................................................................................................................4
Text Conventions ................................................................................................................................................5
Symbols and Signal Words................................................................................................................................5
Symbols on the Information Label ..................................................................................................................5
2. Safety ....................................................................................................................................................................6
Warnings and Safety Instructions ....................................................................................................................6
Requirements for the User.................................................................................................................................8
3. Description of the Device...................................................................................................................................9
3.1. Front View ............................................................................................................................................................9
Back View ..........................................................................................................................................................10
Product Specifications ....................................................................................................................................11
Dimensions.........................................................................................................................................................12
4. Installation ..........................................................................................................................................................13
Safety Instructions for Installation ..................................................................................................................13
Personal Protective Equipment .....................................................................................................................13
Installation Site Requirements ........................................................................................................................13
Rigging ...............................................................................................................................................................14
Angle Adjustment...................................................................................................................................15
Charging the Battery.......................................................................................................................................15
5. Setup ...................................................................................................................................................................16
Warnings and Precautions .............................................................................................................................16
Stand-alone Setup ...........................................................................................................................................16
6. Operation ...........................................................................................................................................................17
Safety Instructions for Operation...................................................................................................................17
Control Modes ..................................................................................................................................................17
Control Panel ....................................................................................................................................................18
Start-up...............................................................................................................................................................18
Menu Overview ................................................................................................................................................19
Main Menu Options .........................................................................................................................................20
Auto Mode ..............................................................................................................................................20
Built-in Programs......................................................................................................................................20
Program 01 ..........................................................................................................................................20
Programs 02–16...................................................................................................................................21
Static color control.................................................................................................................................21
Sound-controlled mode........................................................................................................................21
Settings .....................................................................................................................................................22
Info.............................................................................................................................................................22
Remote Control ................................................................................................................................................23
Auto mode ..............................................................................................................................................25
Built-in Programs......................................................................................................................................25
Sound-controlled mode....................................................................................................................25
Program Speed ..................................................................................................................................26
Strobe ...................................................................................................................................................26
Manual .....................................................................................................................................................26
Color Presets........................................................................................................................................26
7. Troubleshooting .................................................................................................................................................27

3
EventLITE 4/8 Mini Q4
Product code: 44080
8. Maintenance .....................................................................................................................................................28
Safety Instructions for Maintenance.............................................................................................................28
Preventive Maintenance................................................................................................................................28
Basic Cleaning Instructions ...................................................................................................................28
Draining Condensation Water.............................................................................................................29
Corrective Maintenance................................................................................................................................29
9. Deinstallation, Transportation and Storage ....................................................................................................30
Instructions for Deinstallation..........................................................................................................................30
Instructions for Transportation ........................................................................................................................30
Storage...............................................................................................................................................................30
10. Disposal ..............................................................................................................................................................30
11. Approval.............................................................................................................................................................30

4
EventLITE 4/8 Mini Q4
Product code: 44080
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec EventLITE 4/8 Mini Q4
●AC Power Adapter (1,1 m)
●IR Remote control
●User manual
Fig. 01
Intended Use
This device is intended for professional use as a professional outdoor spot. It is not suitable for households
and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.

5
EventLITE 4/8 Mini Q4
Product code: 44080
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment handle (05)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Eye damage hazard
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located on the mounting
bracket of the device.
The information label contains the following symbols:
This device shall not be treated as household waste.
This device is rated IP65.
This device falls under IEC protection class I.
Read the user manual supplied with the device.

6
EventLITE 4/8 Mini Q4
Product code: 44080
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by dangerous voltage inside
There are areas within the device where dangerous touch voltage may be present.
●Do not open the device or remove any covers.
●Do not operate the device if the covers or the housing are open. Before operation, check if the
housing is firmly closed and all screws are tightly fastened.
●Disconnect the device from electrical power supply before service and maintenance, and when the
device is not in use.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class I.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
socket-outlet with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.
●Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.
●Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.
●Keep the connectors sealed with the rubber caps when the connectors are not in use.
●Do not connect the cables from above the connectors, if the device is installed outdoors. Make a
‘drip loop’ in the cable so that rain water cannot enter the device.

7
EventLITE 4/8 Mini Q4
Product code: 44080
WARNING
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at
strobe lights.
CAUTION
Possible eye damage caused by high light intensity
Possibly hazardous optical radiation emitted from this device.
Do not look at the operating light source. May be harmful to the eye.
Do not look at the light source with optical instruments that may concentrate the light output.
Make sure that persons are not looking directly into the light source when the device lights up
suddenly. This can happen when the device is powered or when it receives DMX signal, or when
certain menu items are selected.
Disconnect power supply before servicing.
Wear protective goggles if looking into light source during service or maintenance.
Attention
Power supply
●Before connecting the device to the power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the extension cords and power cables is sufficient for the
required power consumption of the device.
Attention
General safety
●Do not connect the device to a dimmer pack.
●Do not switch the device on and off in short intervals. This decreases the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
For professional use only
This device shall be used only for the purposes it is designed for.

8
EventLITE 4/8 Mini Q4
Product code: 44080
This device is designed to be used as a professional outdoor spot. Any incorrect use may lead to
hazardous situations and result in injuries and material damage.
●This device is not suitable for households and for general lighting.
●This device is not designed for permanent operation.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The power cables are not damaged and do not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP65 rated. IP (Ingress Protection) 65 class means that the device is dust-tight and protected
against harmful effect of water jets.
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

9
EventLITE 4/8 Mini Q4
Product code: 44080
3. Description of the Device
The Showtec EventLITE 4/8 Mini is a battery-powered RGBW spot in a sturdy, IP65-rated aluminium
housing. The battery will last up to 11 hours on a single colour when it is fully charged. The EventLITE 4/8
includes several presets and sound-activated programs, and can be controlled through the display and
buttons on the back or by the included IR-remote controller.
3.1. Front View
Fig. 02
Mounting bracket
2 x adjustment screw
4 x 8 W 4-in-1 RGBW LEDs
Infrared sensor

10
EventLITE 4/8 Mini Q4
Product code: 44080
Back View
Fig. 03
DC connector, 12 V DC
LCD display + control buttons
ON / OFF button
08) Protective valve

11
EventLITE 4/8 Mini Q4
Product code: 44080
Product Specifications
Model:
EventLITE 4/8 Mini Q4
AC power adapter:
Input voltage:
100–240 V AC, 50/60 Hz
Input current:
0,6 A
Output voltage:
12 V DC
Output current:
1,4 A
Physical:
Dimensions:
149 x 103 x 138 mm (L x W x H)
Weight:
1 kg
Optics:
Light source:
4 x 8 W RGBW LEDs
Total luminous flux:
380 lm
Red:
77 lm
Green:
169 lm
Blue:
36 lm
White:
154 lm
Illuminance @2m:
618 lx
Illuminance @3m:
275 lx
Illuminance @5m:
100 lx
CRI:
76
CCT:
13960 K
Dimmer:
0–100 %
Strobe:
0–20 Hz
Beam Angle Circular:
20°
Refresh rate:
3000 Hz
Operation and control:
Control:
Manual, Auto, Built-in programs, IR Remote
Control panel:
7-segment LCD display and menu buttons
Battery:
Battery type:
Lithium-ion
Battery voltage:
12,6 V
Capacity:
2,6 Ah
Runtime (full output):
4 h
Runtime (average):
11 h
Charging time:
5 h
Construction:
Housing:
Die-cast aluminum
Color:
Black
IP rating:
IP65
Cooling:
Convection
Thermal:
Minimum ambient temperature:
-5 °C
Maximum ambient temperature ta:
45 °C
Maximum housing temperature tc:
70 °C
Minimum distance:
Minimum distance from flammable surfaces:
1 m
Minimum distance to lighted object:
0,5 m

12
EventLITE 4/8 Mini Q4
Product code: 44080
Dimensions
Fig. 04

13
EventLITE 4/8 Mini Q4
Product code: 44080
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.
Installation Site Requirements
●The device can be used outdoors.
●The device can be mounted to a truss or other rigging structure.
●The minimum distance between the light output and the illuminated surface must be bigger than
0,5 m.
●The maximum ambient temperature ta= 45 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 45 °C.

14
EventLITE 4/8 Mini Q4
Product code: 44080
Rigging
The device can be positioned on a flat surface (see Fig. 06) or mounted to a truss or other rigging
structure in any orientation. Make sure that all loads are within the pre-determined limits of the supporting
structure.
CAUTION
Restrict the access under the work area during rigging and/or derigging.
To mount the device, follow the steps below:
01) Use a clamp to attach the device to the supporting structure, as shown in Fig. 05. Make sure that the
device cannot move freely.
02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the
secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable through the mounting bracket (01), as shown in Fig. 05.
Fig. 05

15
EventLITE 4/8 Mini Q4
Product code: 44080
Angle Adjustment
You can adjust the angle of the device with the 2 adjustment screws (02).
Turn the adjustment screws (02) counterclockwise to release it.
02) Tilt the device at the desired angle (see Fig. 06).
03) Turn the adjustment screws (02) clockwise to tighten it. Make sure that the device cannot move
freely after the adjustment screws (02) is tightened.
Fig. 06
Charging the Battery
DANGER
Risk of explosion caused by incorrect handling
This device contains a built-in rechargeable lithium-ion battery. The battery is not replaceable. The
battery may explode or cause burns if it is crushed, disassembled or exposed to fire or high temperatures.
●Do not open the device and do not attempt to remove the built-in battery.
This device is delivered with an AC power adapter that is used to charge the battery. Before connecting
the AC power adapter to the socket-outlet, make sure that the power supply matches the input voltage
specified on the information label on the AC power adapter.
To charge the battery follow the steps bellow:
01) Put the device indoors to charge. Connect the AC power adapter to the device. Use only the AC
power adapter delivered with the device.
02) Connect the AC power adapter to the socket-outlet.
During charging, a Con the display is blinking. When charging is completed, the display shows:
●Charge the battery before using the device for the first time.
●Do not deep discharge the battery as this will shorten the battery’s lifetime. Recharge the battery as
early as possible. Do not let the light run until the battery is depleted.
●Make sure that the battery is charged to at least 50 % before storing the device.
It is recommended to charge the device at an ambient temperature between 0 °C and 35 °C.
If the device is charged in a carrying case, leave the case open.
Refer to 3.3. Product Specifications on page 11 for the charge time of the battery.

16
EventLITE 4/8 Mini Q4
Product code: 44080
5. Setup
Warnings and Precautions
DANGER
Electric shock caused by short-circuit
This device is IP65 rated.
●Do not expose the device to conditions that exceed the rated IP class conditions.
●Keep the connector sealed with the rubber cap when the connector is not in use.
Stand-alone Setup
The EventLITE 4/8 Mini Q4 functions as a stand-alone device.
For more information about the control modes, refer to 6.2. Control Modes on page 17.

17
EventLITE 4/8 Mini Q4
Product code: 44080
6. Operation
Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is intended for professional use as an outdoor spot. It is not suitable for households and for
general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.
Control Modes
The EventLITE 4/8 Mini Q4 can be operated as a stand-alone device.
The EventLITE 4/8 Mini Q4 supports the following control modes:
●Stand-alone: Auto, Built-in programs, Preset colors, Manual and Sound-controlled
To run the built-in programs:
01) Run all built-in programs in a sequence in Auto menu. See 6.6.1. Auto on page 20 for more
information.
02) Select one of the 16 built-in programs in Program menu. See 6.6.2. Built-in Programs on page 20 for
more information. Adjust the program speed and strobe frequency.
To run the preset colors:
Select one of the 39 preset colors in Program menu. See 6.6.2.1. Program 01 on page 20 for more
information.
To operate the device manually as a stand-alone device:
●Adjust the colors in Static color control. See 6.6.3. Static color control on page 21 for more
information.
For more information about sound-controlled operation mode see 6.6.4. Sound-controlled mode on
page 21.

18
EventLITE 4/8 Mini Q4
Product code: 44080
Control Panel
A) LCD display
B) MODE button
C) SET button
D) UP button
E) DOWN button
Fig. 07
●Use the MODE button to exit the current submenu and to return to the Main Menu.
●Use the UP/DOWN buttons to navigate through the menus or to increase/decrease numeric values.
●Use the SET button to open the desired menu, to confirm your choice or to set the currently selected
value.
Start-up
Upon start-up the display briefly shows its software version.
Note:
If no button is pressed after 30 seconds of inactivity, the display will turn off. Press any button to turn the
display on.

19
EventLITE 4/8 Mini Q4
Product code: 44080
Menu Overview