Show Tec 42580 User manual

Compact Par 7 Tri V2
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Ordercode: 42580
MANUAL
ENGLISH

1
Ordercode: 42580
Compact Par 7 Tri
Table of contents
Warning...........................................................................................................................................................................2
Safety Instructions .....................................................................................................................................................2
Operating Determinations.......................................................................................................................................4
Rigging........................................................................................................................................................................4
Connection with the mains.....................................................................................................................................5
Return Procedure......................................................................................................................................................6
Claims .........................................................................................................................................................................6
Description of the device.............................................................................................................................................7
Frontside .....................................................................................................................................................................7
Backside .....................................................................................................................................................................8
Installation ......................................................................................................................................................................8
Set Up and Operation...................................................................................................................................................8
Control Modes...........................................................................................................................................................9
One Compact Par (Built-in programs)................................................................................................................9
One Compact Par (Auto).....................................................................................................................................9
One Compact Par (Sound-controlled) ..............................................................................................................9
Multiple Compact Pars (Master/Slave Control)................................................................................................9
Multiple Compact Pars (DMX Control).............................................................................................................10
Fixture Linking...........................................................................................................................................................11
Data Cabling...........................................................................................................................................................11
Control Panel...........................................................................................................................................................12
Control Mode ..........................................................................................................................................................12
DMX Addressing......................................................................................................................................................12
Menu Overview.......................................................................................................................................................13
Main Menu Options................................................................................................................................................14
1. Built-in Programs...............................................................................................................................................14
2. Auto....................................................................................................................................................................15
3. DMX Mode........................................................................................................................................................15
4. Slave Mode.......................................................................................................................................................15
5. Sound-controlled Mode..................................................................................................................................15
DMX Channels.........................................................................................................................................................16
3 channels.............................................................................................................................................................16
4 channels.............................................................................................................................................................16
8 channels.............................................................................................................................................................16
Maintenance................................................................................................................................................................18
Replacing the Fuse.................................................................................................................................................19
Troubleshooting ...........................................................................................................................................................19
No Light.....................................................................................................................................................................19
No Response to DMX..............................................................................................................................................19
Factory Reset...........................................................................................................................................................19
Product Specifications................................................................................................................................................21
Dimensions ...................................................................................................................................................................22

2
Ordercode: 42580
Compact Par 7 Tri
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Compact Par 7 Tri
IEC power cable (1,5 m)
User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual

3
Ordercode: 42580
Compact Par 7 Tri
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
•Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
•Never remove warning or informative labels from the unit.
•Never use anything to cover the ground contact.
•Never lift the fixture holding it by the projector-head, as the mechanics may be damaged. Always
hold the fixture by the transport handles.
•Never place any material over the lens.
•Never look directly into the light source.
•Never leave any cables lying around.
•Do not insert objects into air vents.
•Do not connect this device to a dimmer pack.
•Do not switch the device on and off in short intervals, as this will reduce the device’s life.
•Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
•Do not shake the device. Avoid brute force when installing or operating the device.
•Only use the device indoors, avoid contact with water or other liquids.
•Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
•Only operate the device after having familiarized with its functions.
•Avoid flames and do not put close to flammable liquids or gases.
•Always keep the case closed while operating.
•Always allow a free air space of at least 50 cm around the unit for ventilation.
•Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
•Make sure that the device is not exposed to extreme heat, moisture or dust.
•Make sure that the available voltage is not higher than stated on the rear panel.
•Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
•If the lens is obviously damaged, it has to be replaced.
•If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
•If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.
•If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
•For adult use only. The fixture must be installed beyond the reach of children. Never leave the unit
running unattended.
•Never attempt to bypass the thermostatic switch or fuses.
•For replacement use fuses of same type and rating only.
•The user is responsible for correct positioning and operating of the Compact Par. The manufacturer
will not accept liability for damages caused by the misuse or incorrect installation of this device.

4
Ordercode: 42580
Compact Par 7 Tri
•This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
•Repairs, servicing and electric connection must be carried out by a qualified technician.
•WARRANTY: Till one year after date of purchase.
Operating Determinations
•This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
•The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
•The maximum ambient temperature ta= 40°C must never be exceeded.
•The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
•If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
•Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Improper installation can cause serious injuries and/or damage of property !
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
If the Compact Par is lowered from the ceiling or high joists, professional trussing systems have to be
used.
Use a clamp to mount the Compact Par, with the mounting bracket, to the trussing system.
The Compact Par must never be fixed swinging freely in the room.
The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
When rigging, derigging or servicing the Compact Par, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.

5
Ordercode: 42580
Compact Par 7 Tri
The Compact Par 7 Tri can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International EU Cable UK Cable US Cable Pin
L BROWN RED YELLOW/COPPER PHASE
N BLUE BLACK SILVER NEUTRAL
YELLOW/GREEN GREEN GREEN PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!

6
Ordercode: 42580
Compact Par 7 Tri
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.

7
Ordercode: 42580
Compact Par 7 Tri
Description of the device
Features
The Showtec Compact Par 7 Tri is a light fixture with high output and great effects.
Input voltage: 100-240V AC, 50/60Hz
Power consumption: 50W
Light source: 7 x 3-in-1 RGB LEDs
Lumens: 1540
Lux @2 m: 2002
DMX channels: 3, 4, 8 channels
Drive current: 350 mA
Refresh rate: 3,9 kHz
Max. distance: 20 m
Control mode: DMX 512
Dimmer: 0-100%
Strobe: 0-20Hz
Beam angle: 40°
Control: Built-in programs, Auto, Sound-controlled, Master/Slave, DMX
Connections: 3-pin DMX IN/OUT and IEC power connector IN
Housing: Aluminum and iron
Color: Dark grey and black
Cooling: Aluminum heat sink
Fuse: 1A/250V
Dimensions : 275 x 95 x 256 mm (LxWxH)
Weight: 2,2 kg
Frontside
Fig. 01
01) Mounting bracket with inclination screw
02) Adjustment screw
03) 7 x 3-in-1 RGB LEDs

8
Ordercode: 42580
Compact Par 7 Tri
Backside
Fig. 02
04) Ground/earth connection
05) 100-240V AC, IEC power connector IN + Fuse 1A/250V
06) 3-pin DMX signal connector IN
07) 3-pin DMX signal connector OUT
08) LED display + control buttons
Installation
Remove all packing materials from the Compact Par 7 Tri. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.

9
Ordercode: 42580
Compact Par 7 Tri
Control Modes
There are 5 modes: • Built-in programs
•Auto
•Sound-controlled
•Master/Slave
•DMX-512 (3CH, 4CH, 8CH)
One Compact Par (Built-in programs)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Compact Par is not connected with a DMX cable, it functions as a stand-alone device.
Please see page 14 for more information about the built-in programs.
One Compact Par (Auto)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) When the Compact Par is not connected with a DMX cable, it functions as a stand-alone device.
Please see page 15 for more information about the Auto mode.
One Compact Par (Sound-controlled)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Plug the end of the electric mains power cord into a proper electric power supply socket.
03) Turn on the music. If the device is set to sound-control, the Compact Par will react to the beat of the
music. Please see page 15 for more information about the sound-control options.
Multiple Compact Pars (Master/Slave control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Compact Par and other devices.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
04) Link the units as shown in fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on pages 14-15 (Built-in programs, Auto,
Sound-controlled). This means that you can set your desired operation mode on the master device
and all slave devices will react the same as the master device.
Multiple Compact Pars (Master/Slave Control)
Fig. 03

10
Ordercode: 42580
Compact Par 7 Tri
Multiple Compact Pars (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Compact Pars and other devices.
04) Link the units as shown in fig. 04. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second, third, and fourth units.
05) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Compact Pars DMX Set Up
Fig. 04
Note : Link all cables before connecting electric power

11
Ordercode: 42580
Compact Par 7 Tri
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important: Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX
optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
•DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
•DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
•DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.

12
Ordercode: 42580
Compact Par 7 Tri
The Compact Par 7 Tri can be operated with a controller in control mode or without the controller in
stand-alone mode.
Control Panel
A) LED display
B) MODE button
C) SETUP button
D) UP button
E) DOWN button
Fig. 05
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the side of the device allows you to assign DMX fixture addresses, which is the first
channel with which the Compact Par will respond to the controller.
Please note, when you use the controller, the unit has 8channels.
When using multiple Compact Pars, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Compact Par should be 1(001); the DMX address of the second
Compact Par should be 1+8=9 (009); the DMX address of the third Compact Par should be 9+8=17 (017),
etc. Please, be sure that you do not have any overlapping channels in order to control each Compact
Par correctly. If two or more Compact Pars are addressed similarly, they will work similarly.
Controlling:
After having addressed all Compact Par fixtures, you may now start operating these via your lighting
controller.
Note: After switching on, the Compact Par will automatically detect whether DMX 512 data is received
or not. If there is no data received at the DMX-input, the “LED “ on the control panel will not flash.
If not, the problem may be:
•The XLR cable from the controller is not connected with the input of the Compact Par.
•The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 20 seconds
When no button is pressed for 20 seconds, the display will turn off.
To light up the display, you have to press the MODE, SETUP, UP or DOWN button.
Once you have pressed the button, the display will light up.

13
Ordercode: 42580
Compact Par 7 Tri
Menu Overview

14
Ordercode: 42580
Compact Par 7 Tri
Main Menu Options
1. Built-in Programs
2. Auto
3. DMX Mode
4. Slave
5. Sound controlled
The Compact Par 7 Tri will only show its version number at start-up !
1. Built-in Programs
01) Press the MODE button, until the display shows .
02) Now you can set the built-in programs. Press the UP/DOWN buttons to choose one of the 10 built-in
programs: .
03) When you select , you can use a wide variety of manual color settings.
04) Press the SETUP button to switch between the built-in program menus.
Red
Flash Frequency
Red
Green
Flash Frequency
Green
Flash Frequency
Green
Blue
Flash Frequency
Blue
Flash Frequency
Red
Blue
Flash Frequency
Red
Green
Blue
Flash Frequency
Off

15
Ordercode: 42580
Compact Par 7 Tri
05) When you select , press the SETUP button to switch between the built-in
program menus.
06) You can choose 2 different submenus.
Program Running Speed from 01-99 and FL
Flash Frequency from 00-99
07) Press the SETUP button to scroll through the menu.
2. Auto
01) Press the MODE button, until the display shows .
02) Now you can set the Auto mode.
03) Press the SETUP button to enter the menu. Choose one of the 3 submenus.
Program Running Speed from 01-99 and FL
Flash Frequency from 00-99
Fade from 00-99
04) Press the SETUP button to scroll through the menu.
3. DMX Mode
With this menu you can set the DMX address.
01) Press the MODE button, until the display shows .
02) Now you can choose 512 different DMX addresses.
03) Press the UP/DOWN buttons to select the required address from .
04) Press the SETUP button to enter the DMX menu. Press the UP/DOWN buttons to select one of the 3
DMX modes.
3 channels
4 channels
8 channels
4. Slave Mode
When the display shows , the device will act as a slave device. It will now react the same as the
master device.
5. Sound-controlled Mode
01) Press the MODE button, until the display shows .
02) Turn on the music and the Compact Par will react to the beat of the music.
03) Press the UP/DOWN buttons to set the sound sensitivity. The adjustment range is between
, from OFF to high sensitivity.

16
Ordercode: 42580
Compact Par 7 Tri
DMX Channels
3 channels
Channel 1 – Red Dimmer intensity
0-255 Red from 0 – 100%
Channel 2 – Green Dimmer intensity
0-255 Green from 0 – 100%
Channel 3 – Blue Dimmer intensity
0-255 Blue from 0 – 100%
4 channels
Channel 1 – Dimmer
0-255 0-100% dimmer
Channel 2 – Red Dimmer intensity (Dimmer must be open )
0-255 Red from 0 – 100%
Channel 3 – Green Dimmer intensity (Dimmer must be open )
0-255 Green from 0 – 100%
Channel 4 – Blue Dimmer intensity (Dimmer must be open )
0-255 Blue from 0 – 100%
8 channels
Channel 1 – Dimmer
0-255 0-100% dimmer
Channel 2 – Red Dimmer intensity (Dimmer must be open, CH6 must be closed )
0-255 Red from 0 – 100%
Channel 2 – RGB Macros (Dimmer must be open, CH6 must be set between 1-24 )
0-8 Red (255)
9-17 Red (255), Green (50)
18-26 Red (255), Green (150)
27-35 Red (255), Green (255)
36-44 Red (200), Green (255)
45-53 Red (100), Green (255)
54-62 Red (40), Green (255)
63-71 Green (255)
72-80 Green (255), Blue (50)
81-89 Green (255), Blue (150)
90-98 Green (255), Blue (255)
99-107 Green (150), Blue (255)
108-116 Green (50), Blue (255)
117-125 Blue (255)
126-134 Red (50), Blue (255)
135-143 Red (150), Blue (250)
144-152 Red (255), Blue (255)

17
Ordercode: 42580
Compact Par 7 Tri
153-161 Red (220), Blue (50)
162-170 Red (150), Green (50), Blue (100)
171-179 Red (50), Green (180), Blue (220)
180-188 Red (50), Green (220), Blue (100)
189-197 Red (150), Green (220)
198-206 Red (150), Blue (220)
207-215 Green (180), Blue (220)
216-224 Green (220), Blue (50)
225-233 Red (220), Green (100), Blue (50)
234-242 Red (220), Green (200), Blue (100)
243-251 Red (255), Green (200), Blue (150)
252-255 Red (255), Green (255), Blue (255)
Channel 2 – Program Speed (CH6 must be set between 25-249 )
0-255 Program speed, from slow to fast
Channel 2 – Sound Sensitivity (CH6 must be set between 250-255 )
0-255 Sound sensitivity, from low to high sensitivity
Channel 3 – Green Dimmer intensity (Dimmer must be open )
0-255 Green from 0 – 100%
Channel 4 – Blue Dimmer intensity (Dimmer must be open )
0-255 Blue from 0 – 100%
Channel 5 – Strobe (Dimmer must be open )
0-9 Closed
10-255 Strobe effect, from low to high frequency
Channel 6 – Color Programs (Dimmer must be open )
0 Not functional
1-24 29 static color programs via CH2
25-49 Program 2 (7-color, color flow) R, RG, G, GB, B, RB, RGB
50-74 Program 3 (3-color, color flow) R, G, B
75-99 Program 4 (7-color, color switch) R, RG, G, GB, B, RB, RGB
100-124 Program 5 (3-color, color switch) R, G, B
125-149 Program 6 (fantasy change 1)
150-174 Program 7 (fantasy change 2)
175-199 Program 8 (red color flow)
200-224 Program 9 (green color flow)
225-249 Program 10 (blue color flow)
250-255 Sound-controlled mode
Channel 7 – ID Address
0-9 ID 1-66
10-19 ID1
20-29 ID2
30-39 ID3
40-49 ID4
50-59 ID5
60-69 ID6
70-79 ID7
80-89 ID8
90-99 ID9

18
Ordercode: 42580
Compact Par 7 Tri
100-109 ID10
110-119 ID11
120-129 ID12
130-139 ID13
140-149 ID14
150-159 ID15
160-169 ID16
170-179 ID17
180-189 ID18
190-199 ID19
200-209 ID20
210 ID21
211 ID22
212 ID23









251 ID62
252 ID63
253 ID64
254 ID65
255 ID66
Channel 8 – Fader Response
0-250 CH1, CH2, CH3, CH4 instant fader response
251-255 CH1, CH2, CH3, CH4 delayed fader response
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Compact Par requires almost no maintenance. However, you should keep the unit clean. Otherwise,
the fixture’s light output will be significantly reduced. Disconnect the mains power supply, and then wipe
the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and a soft
cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light
output very quickly.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections
with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying
electric power.

19
Ordercode: 42580
Compact Par 7 Tri
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Gently pry up the fuse cover. The fuse
will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the LEDs, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The LEDs. Return the Compact Par to your Showtec dealer.
03) The fuse. Replace the fuse. See page 19 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Compact Par, as this may
damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.
Factory Reset
In case of unexpected software glitches or when the fixture does not respond properly, it may sometimes
be necessary to reset the fixture. Do as follows:
01) Upon start-up, press and hold down the MODE and SETUP buttons for 5 seconds.