Shuttle DS47 User manual

__p
DS47 Quick Guide【 English 】
53R-DS4703-1001
LThe product’s color and specification will depend on the actual shipping product.
C. Component Installation
D. Complete
1. As shown, unfasten the screw first. Install the Mini PCIe card
into the Mini PCIe slot and affix it with a screw.
4. Put the HDD in the chassis and push toward right untill it inserts into the
SATA&SATA Power Connector.
3. Place the HDD in the rack and secure with the two screws from the side.
1. Replace the covers and refasten the screws.
2 . Complete.
A. Begin Installation
1. Unscrew the two screws of the chassis cover.
For safety reasons, please ensure that the power cord is discon-
nected before opening the case.
1
2
2. Slide the cover forwards and upwards.
5. Refasten the screw.
Left / Right Panel
Back Panel
B1 B6
B3
B1. C-MOS Port
B2. DVI-I Port
B3. HDMI Port
B4. Mic-In
B5. Headphone
B6. USB3.0 Ports x2
B7. LAN Ports x2
B8. DC IN
B2
B7 B8B4 B5
Front Panel F1. USB2.0 Ports x4
F2. Power LED
F3. HDD LED
F4. Power Button
F5. COM 1 :
Support RS232/RS422/RS485
F6. COM 2 :
Support RS232
F7. SD Card Reader
F1 F5
F7
F2 F3
F4
Motherboard Illustration Front
USB 2.0 Ports x4
C11
C2
C3
C4
C5
C6
COM Port 1
LAN Ports x2
USB 3.0 Ports x2
Headphone
Mic In
HDMI Port
DVI-I Port
Power connector - SW1
COM1&COM2
Power Switch - JP2
Fan Connector - Fan1
Power Button - SW3
Mini PCIe slot with
mSATA support - PCIE1
C8 LVDS Connector - LVDS1
Mini PCIe Slot - CN3
CMOS Port - SW2
Battery Connector - CN1
Converter Voltage Select - JP4
Panel Voltage
Select - JP3 C1
C12 Audio Connector - AUDIO2
DDR3 SODIMM slots
HDD LED
Power LED
B. Memory Module Installation
notch
SODIMM slot
45-degree
angle
3
1
2
Latch Latch
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
5. Repeat the above steps to install additional memory modules, if required.
2. Unscrew the rack from the chassis.
Battery Connector
C10
1
Pin Assignments (CN1):
1=V_BAT
2=GND
Pin Assignments
(Audio2):
1=PULL AGND
2=LINE-R
3=N/C
4=LINE-L
5=PULL AGND
6=FRONT_L
7=N/C
8=PRONT_SENSE
9=PULL AGND
10=FRONT_R
Audio Connector
C12
13 11 9 7 5 3 1
14 12 10 8 6 4 2
11=BK_AUDIO-JD
12=MIC1_R
13=AGND
14=MIC1_L
Motherboard Illustration Back
Intel®Celeron®Processor 847
Intel®NM70 Chipset
Super I/O
Power Button
Pin Assignments (SW3)
C2
Jumper Settings
Panel Voltage Select
C1
Pin Assignments (JP3):
1=+3.3V
2=Panel_VDD
3=+5.0V
Converter Voltage Select
Pin Assignments (JP4):
1=+12V
2=INV_PWR_SRC
3=+5V
C3
3 12
FAN_1 connector
C4
Pin Assignments (FAN1):
1=Ground
2=+12V
3=SPEED_SENSE
4=PWM_CTRL
C5
Pin Assignments (SW1):
1=+HD_LED
2=PWR_LED
3=-HD_LED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NUUL
Power Connector
COM1&COM2 Power Switch
C6
JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V
Pin Assignments (JP2):
1=-XRI1 2=COM_-XRI1
3=-XRI2 4=COM_-XRI2
5=+5V 6=+5V
7=COM1_PWR 8=COM2_PWR
9=+12V 10=+12V 1
2
3 5 7 9
4 6 8 10
LVDS Connector
C8
Pin Assignments (LVDS1):
1=N/C
2=Converter-PWR
3=N/C
4=Converter-PWR
5=N/C
6=Converter-PWR
7=GND
8=Converter-PWR
9=N/C
10=GND
11=GND
12=LVDS_DDAT
13=PWMO
14=LVDS_DCLK
15=GND
16=Panel_VDD
17=BKLTEN
18=Panel_VDD
19=PWMO
20=Panel_VDD
21=GND
22=GND
23=LVDS_A3P
24=LVDS_B3P
25=LVDS_A3N
26=LVDS_B3N
27=GND
28=GND
29=LVDS_ACK_P
30=LVDS_BCK_P
31=LVDS_ACK_N
32=LVDS_BCK_N
33=GND
34=GND
35=LVDS_A2P
36=LVDS_B2P
37=LVDS_A2N
38=LVDS_B2N
39=GND
40=GND
41=LVDS_A1P
42=LVDS_B1P
43=LVDS_A1N
44=LVDS_B1N
45=GND
46=GND
47=LVDS_A0P
48=LVDS_B0P
49=LVDS_A0N
50=LVDS_B0N
12
49
50
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer's instructions.
Kensington® Lock Port
Kensington® Lock Port
DC IN
31 2
1 2 3 4
1 2
3
5
7
9
4
6
8
CMOS Port
C13
Pin Assignments (SW2):
1=PWRSW-
2=+5V
3=GND
4=Clear Cmos 1 3
2 4
1 Screw
Mini
PCIe slot
3
2
F6
COM Port 2
62R-DS4700-4801
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
C13
C7 SMBUS
C9 J1 AUTO PWR_SW
C11 Fan2 Connector
C10
SMBUS
Pin Assignments:
1=SMBCLK_SB
2=SMBDATA_SB
3=+5V
4=GND
1
C7
J1 AUTO PWR_SW
Pin Assignments:
SHORT=Disabled
OPEN=Enabled
C9
1
FAN2 connector
C11
Pin Assignments:
1=-FANIO2
2=GND
3=FANPEM2 1
Please load the optimized BIOS settings.
Operation Position:
1) Device must only be used in vertical position with the DVI
port facing up.
2) Please make sure to use either the supplied feet or the VESA
mount.
2.5 inch HDD slot