Shuttle WWN11 Installation instructions

Product Specifications
w w w . s h u t t l e . e u
Shuttle Computer Hand e l s GmbH
Fr itz -St rassman n-S tr. 5
25337 Elmsh orn | Ger many
Tel. [phone]
Fax [phone]
sale s@shu ttl e.eu
Page 1 27 February 2019
© 2019 by Shuttle Computer HandelsGmbH (Germany).All information subjectto change without notice . Pictures for illustration purposes only.
Expansion kit with 4G modem module
and two antennas
this accessory kit you can equip a compatible Shuttle XPC with a built -
in 4G network function. This kit includes a 4G modem module, an M.2
adapter card and two antennas with cables. All you need is an
activated Nano SIM card. Please note that the M.2-2230 slot is used
for this purpose and any existing WLAN cards must first be removed
from the PC.
Feature Highlights
Contents
4G modem-module
M.2 adapter card (LN004)
Fastening screw for 4G modem module
(two-parts)
2x external 4G antennas
2x antenna cables with toothed lock washer
and screw nut
Quick installation guide
4G modem
module
Model: Huawei ME906s-158 (for Europe)
Form factor: 30 x 42 x 2.3 mm (HWD), M.2
LTE data transfer rate: max. 150/50 Mbps @
20MHz Bandwidth Cat4
Further information see next page.
M.2 adapter
card
Riser card for the M.2-2230 Key E slot
Dimensions: 30 x 30 mm
supports one 4G module M.2-3042 Key B
supports one SIM card in Nano format
Two external
antennas
LTE/4G dipole omnidirectional antenna
Multi-band: supports EU frequency bands
(800, 1800, 2600 MHz) for GSM/UMTS/LTE and
the following frequency ranges: 704~960,
1428~1575, 1720~2170, 2400~2690 MHz
Colour: black
Length overall: 135.7 mm
Antenna body: 114.8 mm x 20.1 mm
Impedance: 50 Ohm
Voltage Standing Wave Ratio: <= 3.0
Radiation: Omni, Gain: 2 dBi
Polarisation: vertical
Connector: SMA
Two antenna
cables
RF cable lengths: 20 cm
Connectors:
1) SMA Pigtail female
2) I-PEX MHF 4
Compatibility
The WWN11 accessory kit can be used for
- Shuttle XPC slim DL10J
Supported operation system: Windows 10
Note that you also need a Nano SIM card
XPC Accessory WWN11
4G Adapter Kit Plus
Shuttle Order No. POE-WWN11
Images for illustration only.
Modem Module
Model Huawei
ME906s-158
4G Antennas
with Cables
Shuttle XPC slim DL10J
with installed
4G Adapter Kit Plus
M.2 Adapter
Nano SIM card
(not included)

Product Specifications
w w w . s h u t t l e . e u
Shuttle Computer Hand e l s GmbH
Fr itz -St rassman n-S tr. 5
25337 Elmsh orn | Ger many
Tel. [phone]
Fax [phone]
sale s@shu ttl e.eu
Page 2 27 February 2019
© 2019 by Shuttle Computer HandelsGmbH (Germany).All information subjectto change without notice . Pictures for illustration purposes only.
Specifications: M.2 LTE module Huawei ME906s-158
ME906s-158 is a M.2 interface LTE module with Hisilicon Balong V711 chipset embedded, supporting
LTE (FDD) B1/B2/B3/B5/B7/B8/B20/B28, Qual-band DC-HSPA+/HSPA+/HSPA/WCDMA B1/B2/B5/B8
for Europe and APAC network coverage, low power consumption, Global Navigation Satellite System
(GNSS), and Europe carrier certifications, enabling easier and more flexible design and integration
into end devices.
ME906s-158 is the ideal choice for Notebook, Tablet and Ultrabook etc.
All Huawei modules comply with the RoHS directive and Regional certification.
Size
Height: 30 mm
Width: 42 mm
Depth: 2.3 mm
Weight: approx.6.0g
Form Factor
75-pin M.2/NGFF
Bands
LTE FDD:B1,B2,B3,B5,B7,B8,B20,B28
DC-HSPA+/HSPA+/HSPA/WCDMA:B1,B2,B5,B8
EDGE/ GPRS/GSM 1900/1800/900/850 MHz
Data Transfer
Rate
EDGE: DL 236.8 kbps/UL 236.8 kbps
WCDMA PS: DL 384 kbps/UL 384 kbps
HSPA+: DL 21.6 Mbps/UL 5.76 Mbps
DC-HSPA+: DL 42 Mbps/UL 5.76 Mbps
LTE FDD: DL 150 Mbps/UL 50 Mbps @20M Bandwidth Cat 4
Interface
Antenna interfaces * 2
M.2 Socket
Signal Control interface
USB 2.0 interface high speed
USIM Card interface
Power supply interface
Power Supply
3.135 V to 4.4 V (typical: 3.3 V)
Voice
NA
Other
GNSS:GPS Standalone, A-GPS, LTO, Glonass
SIM Hotswap
IPV6
BodySAR
Tunable Antenna
Temp Range
Normal Operation: -10°C to 55°C
Extended Operation: -20°C to 70°C
Approvals
CE, GCF, FCC, NCC, RCM,
Operator TA: Vodafone, Orange, Telstra, Spark New Zealand

Product Specifications
w w w . s h u t t l e . e u
Shuttle Computer Hand e l s GmbH
Fr itz -St rassman n-S tr. 5
25337 Elmsh orn | Ger many
Tel. [phone]
Fax [phone]
sale s@shu ttl e.eu
Page 3 27 February 2019
© 2019 by Shuttle Computer HandelsGmbH (Germany).All information subjectto change without notice . Pictures for illustration purposes only.
Quick Installation Guide for WWN11
Due to safety reasons, please turn off your computer completely first
and unplug it from the power supply.
1. Unfasten two screws on the back panel and
remove the cover.
2. Use a 6mm screwdriver to puncture the
perforated hole on the back panel from the
outside in. Once the screwdriver passes through
the perforation, carefully remove the metal tag.
If the metal tag still does not detach, carefully
bend it by pushing down from the inside of the
chassis.
Please note that the M.2-2230 slot is used for this
purpose and any existing WLAN cards must first
be removed from the PC.
3. When installing a nano SIM card, please push
the cover to the side and lift it, then carefully
insert the SIM card.
4. Please install the 4G/LTE adapter board into
the M.2 E-Key slot interface as shown and affix it
by tightening the screw with bolt firmly.
5. Please apply the bolt and tighten it firmly.
6. Please install the 4G/LTE
module in the daughter-
board, then tighten the
screw with bolt firmly.

Product Specifications
w w w . s h u t t l e . e u
Shuttle Computer Hand e l s GmbH
Fr itz -St rassman n-S tr. 5
25337 Elmsh orn | Ger many
Tel. [phone]
Fax [phone]
sale s@shu ttl e.eu
Page 4 27 February 2019
© 2019 by Shuttle Computer HandelsGmbH (Germany).All information subjectto change without notice . Pictures for illustration purposes only.
7. Take out the two antenna
cable connectors and
remove the locks and
protective sleeves. Then
connect them to the 4G/LTE
module.
8. Install the antenna cable connectors through the appropriate opening at the back of the chassis.
When leading the cable connector through the opening, check the socket alignment and only push
horizontally. DO NOT turn or twist the cable. Should any difficulties occur, make sure the surface is
clean. Finally, check the alignment again and carefully apply more force.
9. Use the lock to affix the
antenna from the outside.
10. Replace the case cover and fasten its screws.
11. Screw the antennas into
position as pictured. Make sure
they are aligned vertically to
achieve the best possible
signal reception.Make sure the
two antennas are aligned in
the correct direction.

Product Specifications
w w w . s h u t t l e . e u
Shuttle Computer Hand e l s GmbH
Fr itz -St rassman n-S tr. 5
25337 Elmsh orn | Ger many
Tel. [phone]
Fax [phone]
sale s@shu ttl e.eu
Page 5 27 February 2019
© 2019 by Shuttle Computer HandelsGmbH (Germany).All information subjectto change without notice . Pictures for illustration purposes only.
12. Check the following BIOS setting to ensure that the LTE module will be recognized correctly:
Advanced –Onboard Device Configuration –E-Key Device Select = USB
13. Under Windows 10 you can find the cellular status of the 4G modem under „Network & Internet“
and „Cellular“: