Siegenia PremiDoor 76 User manual

ASSEMBLY INSTRUCTIONS
PVC
Window systems
Door systems
Comfort systems
PORTAL
HS



H48.HSKFS0031EN 01.2022 3/108
Contents
Contents
1 GENERAL NOTES........................................6
  ............. 6
1.2 Copyright....................................................... 6
 
Quality for Locks and Hardware (in German

und Beschläge e. V.) ...................................... 6
 ........ 6
1.5 Dimensions ................................................... 6
2 SAFETY.......................................................7
2.1 Intended use ................................................. 7
2.2 Improper use................................................. 7
2.3 Safety notes .................................................. 7
 ......................... 8
3 OPERATING AND INSTALLATION INFOR
MATION .....................................................9
  .......................................... 9
 .................................. 9
4 FABRICATION GUIDELINES......................10
  .................................... 10
4.2 Test reports ................................................. 10
4.3 Threshold .................................................... 11
4.4 Size ranges................................................... 12
4.5 Scheme versions ......................................... 12
5 BASIC HARDWARE...................................13
5.1 Hardware components scheme A ............... 13
5.2 Hardware components scheme C secondary
sash ............................................................. 14
5.3 Hardware components scheme D............... 15
5.4 Hardware list PremiDoor 76........................ 17
5.5 Hardware list only for scheme D................. 18
 .............. 19
6 ASSEMBLY OF BASIC HARDWARE ...........20
6.1 Milling the sliding sash................................ 20
  ........................ 20
  ........................ 21
 ..................... 22
 .......................... 23
 .................. 24
 ................... 24
6.8 Standard/Comfort gear............................... 25
6.8.1 Milling and drilling.............................................. 25
6.8.2 Milling the sliding grip ........................................ 26
6.8.3 Fixing the gear .................................................... 27
6.9 Locking parts ............................................... 28
 ............................ 29
  ........................... 30
 ............................. 30
6.13 Fixing the stop............................................. 31
6.13.1 Stop .................................................................... 31
  .................................................. 32
  ................................................... 32
6.14.2 Spacer D20.......................................................... 33
6.14.3 Cover strip .......................................................... 33
 .......................................................... 34
6.16 Special feature scheme C ............................ 35
 ................................... 35
6.17 Special feature scheme D............................ 36
 ...................................... 36
 ......................................................... 37
6.17.3 Impact seal ......................................................... 38
6.17.4 Seal for sash part................................................ 39
6.17.5 Sealing pad ......................................................... 39
6.17.6 Stop .................................................................... 40
7 BURGLAR RESISTANCE RC2 .....................42
7.1 Hardware components RC 2........................ 42
7.2 Hardware list RC2........................................ 43
7.3 Required preliminary work ......................... 44
  ............................................ 44
7.3.2 Central lock......................................................... 45
  ................ 46
7.4 Fixing the RC2 plate..................................... 47
 
screw........................................................... 48
7.6 Fixing locking part G.................................... 48
8 HOOK BOLT GEAR....................................49
  ........................ 50
8.1.1 Milling and drilling the sliding sash .................... 50
8.1.2 Milling the frame................................................ 51
 ....................... 52
 ............... 53
8.2.2 Adjustment of locking piece .............................. 53

01.20224/108 H48.HSKFS0031EN
Contents
9 400 KG SLIDING SASH..............................54
9.1 Hardware components..............................54
 .............. 55
10 ECO PASS THRESHOLD.............................56
10.1 Hardware components Premidoor 76......... 56
10.2 Hardware list PremiDoor 76........................ 58
10.3 Hardware list PremiDoor 76........................ 59
10.4 Hardware components Premidoor 76 Lux .. 60
10.5 Hardware list Premidoor 76 Lux.................. 61
11 ASSEMBLY OF THRESHOLD ECO PASS.....62
11.1 Sealing wedges............................................ 62
11.2 Screwing on the end caps ........................... 62
11.3 Drilling template jig for frame corner connec-
tor ............................................................... 63
11.4 Frame corner connector ............................. 63
11.5 Running rail ................................................. 64
11.6 Seal REV ...................................................... 64
11.7 Support rail ................................................. 65
11.8 Adapter rail ................................................. 65
11.9 Sealing piece MP......................................... 66
11.10 Sealing pad.................................................. 66
11.11 Flat threshold .............................................. 67
11.12 Fixing the threshold to the frame ............... 67
11.13 Special features scheme D .......................... 68
11.13.1 Sealing piece MP ................................................ 68
 ........................... 68
 .................................... 69
 ........................................ 70
11.14 Special features PremiDoor 76 Lux ............ 71
11.14.1 Sealing piece MP Lux .......................................... 71
  .............................................. 71
11.14.3 Flat threshold ..................................................... 72
11.14.4 Centering disks ................................................... 72
12 ACCESSORIES FOR ECO PASS
THRESHOLD .............................................73
13 ASSEMBLY OF ACCESSORY PARTS FOR
THRESHOLD .............................................75
13.1 Fixing sequence........................................... 75
 .............. 75
  ........................................... 75
 ............................. 75
  ....................................................... 76
13.1.5 Threshold............................................................ 76
 .......................................... 76
14 SUBSTRUCTURE PROFILES ......................77
 ........... 77
  ................ 78
14.2.1 Apply sealant ...................................................... 78
14.2.2 Fixing on the threshold....................................... 78
14.2.3 Threaded axles ................................................... 79
14.2.4 Lining .................................................................. 79
  ................................ 80
 
MENTS .....................................................81
15.1 Hardware components................................ 81
  ............. 82
15.2.1 Milling and drilling the sliding sash .................... 82
 ...................................... 82
 ..................... 83
15.3.1 Corner drive........................................................ 84
15.3.2 Bogie wheels HV................................................. 85
  .......................... 85
  ......................... 86
16 SOFT CLOSE .............................................87
17 ASSEMBLY OF SOFT CLOSE......................88
17.1 Sash milling ................................................. 88
 ............. 88
  ......................... 89
17.4 Tensioning SOFT CLOSE ............................... 90
  ...................... 90
18 SILL INSTALLLATION ................................91
 -
man-speaking markets)............................... 91
19 PROFILE SECTIONS ..................................91
  ............................. 91
20 HANDLE OVERVIEW ................................91
21 LOCKING MONITORING SYSTEM ............92
21.1 General notes.............................................. 92
21.2 Component overview.................................. 93
21.2.1 Components for the locking monitoring system
(according to VdS-C) ........................................... 93
  ...................................... 94
  ............. 95

H48.HSKFS0031EN 01.2022 5/108
Contents
 
magnet clamp..................................................... 96
 ....................... 97
  ..........................................................98
23 MAINTENANCE......................................100
24 CLEANING AND MAINTENANCE............100
25 OPTIONAL ACCESSORY COMPONENTS.102
25.1 Packer for stop .......................................... 102
  ............... 102
  ............................ 103
25.3.1 Packer for locking part...................................... 103
25.4 AEROCONTROL for PORTAL HS elements
(scheme A) ................................................ 104
25.4.1 Magnet AEROCONTROL UMA 002.................... 104
 ................................ 104
  .................................... 105