Siemens FDCIO422 Service manual

SIEMENS
Industry, Inc.
A6V10324662_g_en_US
2016-01-20 Building Technologies Division
Model FDCIO422
Addressable Input/Output module S54322-F4-A1
Installation Instructions
Download link
Desigo:
https://www.buildingtechnologies.siemens.com/extranet/ba-sp/
Download link Cerberus PRO:
http://iknow.us009.siemens.net/infolink
INTRODUCTION
The FDCIO422 is used for the connection of up
to 2 independent Class A or 4 independent
Class B dry N/O configurable contacts. Input
lines can be supervised for open, short and
ground fault conditions (depending on EOL
termination resistor and class configuration).
Inputs can be independently configured via the
fire control panel for alarm, trouble, status or
supervisory zones.
The FDCIO422 has 4 programmable outputs
with 4 potential-free latching type form A relay
contacts for fire control installations.
Status indication per LED for each input and
output plus 1 LED for general status of the
device. Power supply via FDnet (supervised
power limited).
·Including 4 EOL devices (470 Ω)
·3 separators to separate the power limited
wiring from the non-power limited.
Separators are delivered in 3 different sizes
for standard 4 11/16-inch box, 4 11/16-inch
extension ring and 5-inch box (RANDL).
CAUTION
Electric shock!
High voltages may
occur on the terminals.
Always use a faceplate
and the separator(s).
Figure 1 FDCIO422 cage and carrier
CAUTION
This device is not intended for
applications in explosive environments.
Class A is equivalent to DCLA (Canada)
Class B is equivalent to DCLB (Canada)
For complete configuration and
commissioning of the FDCIO422 also refer
to the user documentation of your panel,
especially for the software tool used for
configuration.
Figure 2 Removing the cage and the terminal strips from the carrier

2
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
PROGRAMMING INSTRUCTIONS
Refer to Figure 3 to locate the opening on the
cage cover that allows access to the programming
holes which are on the FDCIO422 printed circuit
board.
To connect the FDCIO422 to the DPU or 8720
Programmer/Tester, insert the plug from the
DPU/8720 cable provided with the
Programmer/Tester into the opening on the front
of the FDCIO422. Be sure to insert the locating
tab on the plug into the slot for the locating tab as
shown in Figure 3. Minimum Firmware revision of
the DPU must be 9.00.0004, for 8720 must be
5.02.0002.
NOTICE
To prevent potential damage to the DPU
(refer to manual P/N 315-033260) or to
the 8720 (refer to manual P/N 315-
033260FA) DO NOT connect a FDCIO422
to the DPU or 8720 until the cage is
removed from the carrier (Figure 2).
Figure 3 Connecting the DPU/8720 plug to the cage
Modul Status LED
Flash Color
Condition
Flash Intervals
(Seconds)
Green
*
Normal supervisory operation.
10
Amber
Device is in trouble
4
Red
Locate
/
Alarm
1
Input/Output active
10
No Flashes
Device is not powered, or
replacement is needed.
-
*
LED can be turned off. Please follow the corresponding
description of the Panel used.
WIRING
Refer to Figure 11. Refer to the appropriate wiring diagram and wire the addressable input/output module
accordingly.
Recommended wire size: 18 AWG minimum and 14 AWG maximum
Wire larger than 14 AWG can damage the connector.
(Refer to Figures 2 and 3). Follow the instructions in the DPU manual or 8720 manual to program the
FDCIO422 to the desired address. Record the device address on the label located on the front of the
module. The FDCIO422 can now be installed and wired to the system.
Figure 4 Wiring multiple switches
INPUT NOTES:
1. There can be any number of normally open dry contact switches.
2. The end of line device must be located at the last switch.
3. Do not wire a normally closed switch across the end of line device in a normally open wiring.
4. Multiple switches: for open wiring supervision only.
INPUT ACTIVE LED,
red
INPUT TROUBLE LED,
yellow
PLUG FROM DPU/8720
PROGRAMMER/TESTER
LOCATING
TAB
OUT A
OUT B
OUT C
OUT D
IN 1
IN 2
IN 3
IN 4
IN 1 trouble
IN 2 trouble
IN 3 trouble
IN 4 trouble
SLOT FOR
LOCATING TAB
PROGRAMMING
HOLES
OUTPUTACTIVE LED,
red
1)
1)
Command for the activation
of the output received by the
control unit
PROGRAMMABLE SWITCHES (SEE NOTES 1, 2 AND 3)
PROGRAMMABLE SWITCHES (SEE NOTES 1 AND 3)
Rp ½ W470 Ω
EOL
UL 864 CLASS STYLE BB UL 864 CLASS STYLE AD
IN 1-4
IN1/IN2
IN3/IN4

3
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
Power limited wiring
In compliance with NEC Article 760, all power
limited fire protective signaling conductors must be
separated a minimum of ¼ inch from all of the
following items located within an outlet box:
·Electric light
·Power
·Class 1 or non-power limited fire protective
signaling conductors
To meet the above requirements, the following
guidelines must be observed when installing this
input/output module.
If non-power limited wiring is not used
within this outlet box, then these
guidelines do not apply. In that case, be
sure to follow standard wiring practices.
Wiring entering outlet box
All power limited wiring must enter the outlet box
separately from the electric light, power, class 1,
or non-power limited fire protection signaling
conductors. For the FDCIO422, wiring to the
terminal blockfor line and inputs must enter the
outlet box separately from the terminals for
outputs.
For the output terminals, protection with a fuse is
recommended. Refer to Figures 6 and 9.
WIRING AT THE TERMINAL BLOCKS
Minimize the length of wire entering the
outlet box.
Figure 6 Power Limited Wiring
Separators
The separators must be used when the relay
contacts are connected to non-power limited lines.
Mount the correct separator in the box used
(4 11/16-inch box and 5-inch box). If an extension
ring is used in connection with a 4 11/16-inch
square box an additional separator has to be
mounted in the extension ring.
The separators create two compartments to
separate the wires as shown in Figure 5.
Figure 5 Mounting the separators in the boxes
P
N
NP
DO NOT USE!
P = POWER LIMITED
N = NON-POWER LIMITED
11 16
18
11 16
ADAPTER PLATE
11 16
4 INCH SQUARE BOX
WITH EXTENSION RING
INCHES DEEP (29.5 in³)
1½

4
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
MOUNTING
Input/output module FDCIO422 can be mounted
directly into a 4 11/16-inch square box or 5-inch
square box.
An additional extension ring can be mounted on
the 4 11/16-inch square box with two screws.
For mounting the input/output module in the
5-inch square box use a 4 11/16-inch adapter
plate.
Fasten the module to the square box with the
4 screws provided with the box.
Fasten the faceplate on the carrier using the
2 screws provided with the FDCIO422.
Be sure to program the FDCIO422 before
fastening the faceplate to the unit.
Volume allowance FDCIO422
FDCIO422 Volume 11.7 inch
3
,
max. 20 conductors
Check NFPA70, National Electric Code
‘314.16 Number of Conductors in Outlet,
Device and Junction Boxes, and Conduit’,
Table 314.16(A) and (B), to choose the
correct metal box (4 11/16-inch square box,
411/16-inch square box with extension ring
or 5-inch square box).
WARNING
It is not allowed to use the module without
the faceplate. Remove the faceplate for
service and maintenance reasons only!
Figure 7 Mounting the FDCIO422
TECHNICAL DATA
Operating voltage: DC 12 – 32 V
Operating current
(quiescent): 1 mA
Absolute maximum
peak current: 1.92 mA
Maximum current
connection factor2):4
Relays output
1)
:
(normally open /
normally closed)
DC 30 V / AC 125 V
Max. 4x 5 A or
2x 7 A (OUT B, C) or
1x 8 A (OUT C)
Operating
temperature: 32 – 120 °F / 0 – 49 °C
Storage temperature: -22 – +140 °F / -30 – +60 °C
Humidity: 5 – 85 % R.H. (not freezing
and condensing at low
temperature)
Communication
protocol: FDnet (supervised Signaling line circuit, Power limited)
Color: Carrier: ~RAL 9017
Cage cover: transparent
Cage: ~RAL 9017
Faceplate: white
Standards: UL 864, ULC-S 527, FM 3010,
UL 2572
Approvals: UL / ULC / FM
System compatibility FC2005, FC2025, FC2050,
FV2025, FV2050, FC901,
FC922, FC924, FV922,
FV924 & FireFinder XLS
Dimensions: 4.1 x 4.7 x 1.2 inch
Volume (cage and
carrier): 11.7 inch
3
1)
2 coil latching type, dry contact, Form A
2)
Average charge current of the device. 1 Load Unit (LU)
equals to 250 µA
11 16
18
11 16
ADAPTER PLATE
11 16
4 INCH EXTENSION RING
INCHES DEEP (29.5 in³)1½
FDCIO422
CONTROL MODULE BARRIER
(SUPPLIED)
FACEPLATE
5 INCHES
(SUPPLIED)
½

5
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
Figure 8 Line wiring
WIRING NOTES:
6.All supervised switches must be held closed and/or
open for at least 0.25 s to guarantee detection
(depending on filter time).
7.End of line device: 470 Ω± 1 %, ½W resistor,
delivered with the device (4x).
8.The inputs must be wired potential-free.
9.FDCIO422 is polarity insensitive. Line -6 and Line -5
can be either line of the loop.
10. Electrical ratings:
FDnet voltage maximum: DC 32 V
Absolute maximum peak current: 1.92 mA
11. Supervised switch ratings:
Monitoring voltage: 3 V
Cable length input: Max. 200 ft
Input shielding required
for cable lengths from: 30 ft – 200 ft
Max. C
Line
to
line
:0.02 µF
Max. C
Line
to
shield
:0.04 µF
Max. line size: 14 AWG
Min. line size: 18 AWG
12. The operating current may never exceed the rated
current.
13. As the outputs are not supervised by the module
use an external supervision for critical applications.
14. Choose the correct AWG size for the intended
operating current.
15. Connect incoming and outgoing shields together in
an acceptable means. Insulate shields, do not make
any connections to the device or back box.
16. Use shielded and/or twisted wire to connect the
switch wiring and keep the wiring as short as
possible.
17. Tie the switch wiring shield to the local earth
ground (at only one end, refer to Figure 9). For
multiple switches on the same input, connect
incoming and outgoing shields together in an
acceptable means. Insulate shields, do not make
any connections to the device or back box.
18. Positive and negative ground fault detected at
<25 kΩfor inputs 1 – 4.
·The shield from the input must be
connected to a known good earth
ground for proper operation.
We recommend to use the earth
connector in the electrical box.
·Conductive armored or conductive
metal conduit cables are sufficient as
shielding.
·
If a proper connection of the shield to
a known good ground cannot be
assured then unshielded cabling
should be used.
Figure 9 Input shielding
19. Relay contact ratings:
Cable length output: Max. 200 ft
PROGRAMMABLE
RELAY CONTACTS
SEE NOTES 12, 13, 14 AND 19
FROM CONTROL PANEL
OR PREVIOUS
ADDRESSABLE DEVICE
TO NEXT
ADDRESSABLE DEVICE
END OF LINE DEVICE Rp
SEE NOTE 7
SUPERVISED
PROGRAMMABLE SWITCH
SEE NOTES 6, 8 AND 11
PROGRAMMABLE
RELAY CONTACTS
SEE NOTES 12, 13, 14 AND 19
S
E
E
N
O
T
E
S
9
,
1
0
A
N
D
1
5

6
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
Normally open / Normally closed:
Define intended max. ambient temperature (77 °F, 100 °F, 120 °F) andmax. power factor from load.
Then find correlated possible max. current ratings in table below:
up to DC 30 V up to AC 125 V
P.F. / Amb. Temp. 0 - 77°F / 0 - 25°C ≤100°F / ≤38°C ≤120°F / ≤49°C 0 - 77°F / 0 - 25°C ≤100°F / ≤38°C ≤120°F / ≤49°C
resistive 14x 5 A 2x 7 A
1x 8 A
4x 3 A
2x 4 A
1x 5 A
4x 2 A
2x 2.5 A
1x 3 A
4x 5 A
2x 7 A
1x 8 A
4x 3 A
2x 4 A
1x 5 A
4x 2 A
2x 2.5 A
1x 3 A
inductive 0.6 4x 5 A 2x 5 A
1x 5 A
4x 3 A
2x 4 A
1x 5 A
4x 2 A
2x 2.5 A
1x 3 A
4x 5 A
2x 7 A
1x 7 A
4x 3 A
2x 4 A
1x 5 A
4x 2 A
2x 2.5 A
1x 3 A
inductive DC 0.35
AC 0.4
4x 3 A
2x 3 A
1x 3 A
4x 3 A
2x 3 A
1x 3 A
4x 2 A
2x 2.5 A
1x 3 A
4x 5 A
2x 7 A
1x 7 A
4x 3 A
2x 4 A
1x 5 A
4x 2 A
2x 2.5 A
1x 3 A
4x Out: A,B,C,D ; 2x Out: B,C ; 1x Out: C ; use only indicated outputs
PF 0.6 (60 Hz) ≡L/R max. 3.5 ms
PF 0.35 (60 Hz) ≡L/R max. 7.1 ms ≡max. ind. Load at any case
Diagnostics
NOTICE
AC ratings MUST NOT be used with modules
with ES<10. You will find the ES on the label.
Indication
Actions
Normal, no fault is present
In-/Output module is fully functional none
Fault is present
Error with the input circuitry (open line, short circuit, deviation) Checking the input circuitry (parameter setting, resistors, short-circuit, open line)
Invalid parameter settings Check the parameter setting
Supply error - Check detector line voltage
- Replace device
Software error (Watchdog error) Replace device
Storage error Replace device
Communication error between device and control panel Remedy cause
Note: Any general message can be displayed together with another status.
Configuring the outputs Configuring the inputs
For configuring the outputs, proceed as follows:
a.Determine in which position the contact is
active. The contact can be active when it is:
- Closed (normally open, NO)
- Open (normally closed, NC)
b.After activating the contact remains:
– Permanently active
– Active only for a certain period of time. How
long the contact remains active can be
configured as well (pulse duration). This is only
to be used in the application of:
●Resetting the four wire device F5000
Reflective Beam Smoke Detector, P/N 500-
050261.
The following settings are possible:
10 s 15 s 20 s
c.Determine the behavior of the output in case of
error on the communication line (open line to
the control panel, FDCIO422 power failure).
The following configurations are possible for
the behavior in case of a failure (default
positions):
– Output position remains the same as
before the error
– Output is activated
– Output is deactivated
For configuring the inputs, proceed as follows:
a.Configure the inputs as 4 Class B (DLCB) or
2 Class A (DLCA).
b.Define the type of input (danger input or status
input):
- Status input: triggers status change
- Danger input: triggers alarm
c.Determine the type of monitoring and the
monitoring resistors (refer to Figure 10):
- Class A only open no EOL
- Class B only open RP470 Ω
- Class B open and short RS100 Ωand RP470 Ω
d.Define the input filter time. The following settings
are possible:
0.25 s 0.5 s 1 s
The configuration of the input must
correspond to the actual wiring.
An EOL must be mounted to the input in case of this
input is NOT used.
Follow the instructions in the
corresponding panel manual for
programming the FDCIO422 properly:
P/N A6V10333724 and
P/N A6V10336897.

7
Siemens Industry, Inc.
Building Technologies Division
A6V10324662_g_en_US
2016-01-20
·The 2x Class A inputs are identified by the panel as Input 1 and Input 2.
·Class A and Class B cannot be configured at the same time!
2x Class A or 4x Class B!
Figure 10 FDCIO422 input wiring Class A and Class B (for details of Line 1 and 2 wiring see Figure 8, for details of the
input wiring see Figure 11.)
OUT A
OUT B
OUT C
OUT D
OUT A
OUT B
OUT C
OUT D
OUT A
OUT B
OUT C
OUT D
470 ±1 % ½ W
Ω
Rs RpRp
please order separately
ORDER NO. S54312-F7-A1
100 ±1 % ½ W
Ω
ONLY OPEN MONITORING
ONLY OPEN MONITORING
a
b
a
b
a
b
a
b
a
b
a
b
a
b
a
b
a
b
a
b
a
b
a
b
UL864 CLASS STYLE
BB
UL864 CLASS STYLE
BC
UL864 CLASS STYLE
AD
included

Siemens Industry, Inc.
Building Technologies Division
8, Fernwood Road
Florham Park, New Jersey 07932
www.siemens.com/buildingtechnologies
Siemens Canada Limited
Building Technologies Division
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 Canada
© Siemens Industry, Inc. 2012-2016
Data and design subject to change without notice.
Document ID
8
Edition
A6V10324662_g_en_US
2016-01-20
End of Line Resistor Wiring Overview
①CAUTION: FOR SYSTEM SUPERVISION – FOR TERMINALS IDENTIFIED WITH A ①DO NOT USE
LOOPED WIRE TERMINALS. BREAK WIRE RUN TO PROVIDE SUPERVISION OF CONNECTIONS.
②Use Siemens TB-EOL terminal P/N S54322-F4-A2 or equivalent.
③Use only normally open dry contact SWITCHES for the inputs
Figure 11 Wiring end of line and switch
·
Use a 4 or 2 pole UL/ULC recognized SWITCH.
· Switch Terminal must be capable of two conductors at one terminal.
· EOL Resistor wiring must be done according to UL 864 and ULC-S527, chapter ‘EOL Devices’.
·The EOL Resistors must be connected at the end of the input lines.
·
No addressable device or 2
-
wire smoke detectors can be connected to the inputs.
ACCESSORIES
DEVICE
ORDER NO.
EOL resistor 100
Ω
±
1
%
½
W
S54312
-
F7
-
A1
SIEMENS
INDUSTRY, INC.
4
11
/16
-
inch adapter plate (optional)
M
-
411000
RANDL
INDUSTRIES, INC.
5
-
inch Box (optional)
T55017
RANDL
INDUSTRIES, INC.
5
-
inch Box (optional)
T55018
RANDL
INDUSTRIES, INC.
5
-
inch Box
(optional)
T55019
RANDL
INDUSTRIES, INC.
TB
-
EOL terminal
S54322
-
F4
-
A2
SIEMENS
INDUSTRY, INC.
SHIELDED WIRE MAX: 200 FT
18 - 14 AWG
OPEN AND SHORT SUPERVISION
OPEN
CLASS B STYLE C, OPEN AND SHORT WIRING SUPERVISION
SHIELDED WIRE MAX: 200 FT
18 - 14 AWG
OPEN SUPERVISION
OPEN
IN1
-
4
IN1
-
4
X
EARTH
GND
CLASS A STYLE D, OPEN WIRING SUPERVISION CAUTION: BE AWARE OF THE INPUT POLARITY IN CLASS A MODE
SHIELDED WIRE MAX: 200 FT
18 - 14 AWG
OPEN
OPEN
X
EARTH
GND
CLASS B STYLE B, OPEN WIRING SUPERVISION
OPEN SUPERVISION
X
EARTH
GND
470 Ω
100 Ω
470 Ω
470 Ω
for UL: mount EOL directly on the last SWITCH terminal for ULC: mount EOL on the TB-EOL terminal
①
①
①
TB-EOL ②
TB-EOL ②
SWITCH ③
SWITCH ③SWITCH ③
①
①
①
①
③
SWITCH
①
①
①
①
①