Siemens SIMATIC ET 200C User manual

Preface, Contents
Configuration 1
ET 200C Configuration Options 2
ET 200C Components 3
Mechanical and Electrical
Installation 4
Address Assignment and Param-
eterization with COM ET 200 5
Startup and Test with
COM ET 200 6
Fault Diagnostics with the
IM 308-B 7
Fault Diagnostics with the
IM 308-C 8
Connection of the
ET 200 Handheld 9
General Technical Specifications 10
Digital Modules 11
Analog Modules 12
Other ET 200C Components 13
Pin Assignments of the ET 200C
Modules A
Type files B
Safety-Related Guidelines C
Glossary, Index
EWA 4NEB 812 6119-02b
Edition 03
ET 200C
Distributed I/O Station
Manual
SIMATIC

This manual contains notices which you should observe to ensure your own personal safety,
as well as to protect the product and connected equipment. These notices are highlighted in
the manual by a warning triangle and are marked as follows according to the level of danger:
!Danger
indicates that death, severe personal injury or substantial property damage will result if
proper precautions are not taken.
!Warning
indicates that death, severe personal injury or substantial property damage can result if
proper precautions are not taken.
!Caution
indicates that minor personal injury or property damage can result if proper precautions are
not taken.
Note
draws your attention to particularly important information on the product, handling the
product, or to a particular part of the documentation.
Only qualified personnel should be allowed to install and work on this equipment. Quali-
fied persons are defined as persons who are authorized to commission, to ground, and to tag
circuits, equipment, and systems in accordance with established safety practices and stan-
dards.
The device/system may only be set up and operated in conjunction with this manual.
Note the following:
!Warning
This device and its components may only be used for the applications described in the cata-
log or the technical description, and only in connection with devices or components from
other manufacturers which have been approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored, set up, and
installed correctly, and operated and maintained as recommended.
SIMATICand SINECare registered trademarks of SIEMENS AG.
Copyright
Copyright Siemens AG 1994 All Rights Reserved
The reproduction, transmission or use of this document or its contents
is not permitted without express written authority. Offenders will be
liable for damages. All rights, including rights created by patent grant
or registration of a utility model or design, are reserved.
Exclusion of Liability
We have checked the contents of this manual for agreement with the
hardware and software described. Since deviations cannot be preclu-
ded entirely, we cannot guarantee full agreement. However, the data
in this manual is reviewed regularly and any necessary corrections
included in subsequent editions. Suggestions for improvement are
welcomed.
Technical data subject to change.
Safety Guidelines
Qualified Personnel
Correct Usage

iii
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Preface
The information in this manual will enable you to:
install, connect and operate the ET 200C distributed I/O station,
look up the module characteristics and technical data.
This section shows you how the manual is structured.
What configuration options do I
have with ET 200C?
What are the components of ET 200C?
What is involved in mechanical and
electrical installation?
How do I perform startup and testing
with COM ET 200?
Errors?
Technical data?
Chap. 2
Chap. 3
Chap. 4
Chap. 6
Chap. 7, 8
What is ET 200C? Chap. 1
How do I set the address and parameters
with COM ET 200? Chap. 5
How do I connect the ET 200 handheld? Chap. 9
Chap. 10, 11, 12, 13
Pin assignment, type files? Appendix A, B
This manual covers all the ET 200C modules that can be addressed with the
DP standard bus protocol. Each of these ET 200C modules has an order
number beginning with 6ES7 (See Chapter 10.1).
This manual is applicable to operation of ET 200C in conjunction with
IM 308-B master interface and COM ET 200
IM 308-C master interface and COM ET 200 Windows.
Operation with the IM 308-B master interface and COM ET 200 is described
in detail in this manual.
Purpose
of the Manual
Contents
of the Manual
Scope
of the Manual

iv ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
As regards operation of ET 200C with the IM 308-C master interface and
COM ET 200 Windows, this manual describes only parameterization with
COM ET 200 Windows. See the manual entitled ET 200 Distributed
I/O System (order number 6ES5 998-3ES12) for detailed information on how
to use COM ET 200 Windows and on working with the FB IM 308C standard
function block.
COM ET 200 Windows has an online Help system that provides valuable
assistance for starting up and operating the ET 200C modules.
This manual follows on from the manual entitled ET 200 Distributed
I/O System, which is the master description for the series.
You must read and understand the manual ET 200 Distributed I/O System in
order to use this manual.
A number of features in this manual will help you to obtain quick access to
the information you require:
At the start of the manual you will find a general table of contents, plus a
list of all the illustrations and a list of all the tables in the manual.
On each page throughout the manual, the bold-face headings on the left
summarize the contents of the individual passages.
The Appendices are followed by a Glossary containing definitions of the
important terms used in this manual.
The manual closes with a detailed index that you can use to find
information on the topic of your choice.
The ET 200C modules function as DP standard slaves in accordance with the
definitions of DIN E 19245, Parts 1 and 3.
Please address all questions about the ET 200C distributed I/O station to:
Hotline SIMATIC
Erlangen
Phone (+ 49 for Germany) 9131/7-43344
You will find suggestion sheets at the end of the manual. Please note any
suggestions or proposals you may have on these sheets and return them to
use. Your suggestions will help us improve the next edition of the manual.
Scope
of the Manual
(Continued)
Other Important
Manuals
Quick Access
Standards
Questions
Suggestions
Preface

v
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Contents
1 Configuration 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 What is the ET 200? 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 What is the ET 200C? 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 ET 200C Configuration Options 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Overview of the ET 200C Configuration Options 2-2. . . . . . . . . . . . . . . . . .
2.1.1 Configuration with Power Supply Connector without T Connector 2-4. . . .
2.1.2 Configuration with Power Supply Connector and with T Connectors 2-7.
2.1.3 Configuration using Several Power Supply Connectors 2-10. . . . . . . . . . . .
2.1.4 Configuration without Power Supply Connector 2-12. . . . . . . . . . . . . . . . . . .
2.1.5 Configuration with Programmer Connector 2-16. . . . . . . . . . . . . . . . . . . . . . .
3 ET 200C Components 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Digital Input Module ET 200C; DI 8 DC 24V
(6ES7 141-0BF00-0XB0) 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Digital Output Module ET 200C; DO 8 DC 24V/0.5A
(6ES7 142-0BF00-0XB0) 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Digital Output Module ET 200C; DO 8 DC 24V/2A
(6ES7 142-0BF10-0XB0) 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24V
(6ES 143-0BL00-0XB0 and 6ES7 143-0BL10-0XB0) 3-8. . . . . . . . . . . . . .
3.5 Analog Input Module ET 200C; AI 4/8 12 Bit
(6ES7 144-0KH00-0XB0) 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6 Analog Input Module ET 200C; AI 4 12 Bit
(6ES7 144-0HF00-0XB0) 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7 Analog Output Module ET 200C; AO 4 12 Bit
(6ES7 145-0HF00-0XB0) 3-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8 T Connector (6ES5 762-2CT11) 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9 Power Supply Connector (6ES5 762-2CS11) 3-18. . . . . . . . . . . . . . . . . . . . .
3.10 Programmer Connector (6ES5 762-2CA12) 3-19. . . . . . . . . . . . . . . . . . . . . .
3.11 Cables 3-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.12 Terminating Resistor (6ES5 755-2CA11) 3-22. . . . . . . . . . . . . . . . . . . . . . . . .
3.13 Adapter Cable (6ES5 755-8CA11) 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vi ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
4 Mechanical and Electrical Installation 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Installation of ET 200C 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Electrical Wiring of the ET 200C Distributed I/O Station 4-3. . . . . . . . . . . .
4.2.1 Grounded Configuration 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Ungrounded Configuration 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Wiring of the ET 200C 4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1 Wiring of the Bus Connection 4-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2 Wiring of ET 200C; DI 8 DC 24V (6ES7 141-0BF00-0XB0) 4-13. . . . . . .
4.3.3 Wiring of ET 200C; DO 8 DC 24V/0.5A (6ES7 142-0BF00-0XB0)
and ET 200C; DO 8 DC 24V/2A (6ES7 142-0BF10-0XB0) 4-15. . . . . . .
4.3.4 Wiring of ET 200C; DI 16/DO 16 DC 24V/2A
(6ES7 143-0BL00-0XB0) 4-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5 Wiring of ET 200C; DI 16/DO 16 DC 24V/2A
(6ES7 143-0BL10-0XB0) 4-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.6 Wiring of ET 200C; AI 4/8 12 Bit (6ES7 144-0KH00-0KB0) 4-21. . . . . . .
4.3.7 Wiring of ET 200C; AI 4 12 Bit (6ES7 144-0HF00-0KB0) 4-30. . . . . . . . .
4.3.8 Wiring of ET 200C; AO 4 12 Bit (6ES7 145-0HF00-0KB0) 4-35. . . . . . . .
4.3.9 Wiring of the Load Voltage Supply 4-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.10 Wiring of the External Power Supply to the PS Connector 4-42. . . . . . . . . .
4.4 Setting DIL Switches on Analog Modules of ET 200C 4-43. . . . . . . . . . . . . .
4.4.1 Setting the Station Number of Analog Modules by Means of
DIL Switch Block S1 4-44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2 Setting the Measurement Type for Analog Module ET 200C;
AI 4/8 12 Bit 4-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.3 Setting Measurement Type for Analog Module ET 200C;
AI 4 12 Bit 4-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.4 Setting Connection Mode for Analog Module ET 200C;
AO 4 12 Bit 4-52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Address Assignment and Parameterization with COM ET 200 5-1. . . . . . . . . . . .
5.1 Address Assignment with COM ET 200 V4.x 5-2. . . . . . . . . . . . . . . . . . . . . .
5.1.1 Enter Station Number 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.2 Enter Address Area and Station Type 5-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1.3 Enter Station Name, Addresses and Address Identifier 5-7. . . . . . . . . . . . .
5.1.4 Enter Parameterization Frame with COM ET 200 V4.x 5-12. . . . . . . . . . . . .
6 Startup and Test with COM ET 200 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Connecting the Programmer 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Starting Up and Testing the ET 200C Distributed I/O Station 6-4. . . . . . . .
6.3 Testing the ET 200C Distributed I/O Station 6-6. . . . . . . . . . . . . . . . . . . . . .
7 Fault Diagnostics with the IM 308-B 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Using LEDs to Diagnose Problems 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Using COM ET 200 V4.x to Diagnose Problems 7-5. . . . . . . . . . . . . . . . . . .
7.3 Using STEP 5 to Diagnose Problems (Station Diagnosis) 7-7. . . . . . . . . .
7.3.1 “Overview” Diagnostics 7-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.2 ”Parameter Assignment and Addressability” Diagnostics 7-12. . . . . . . . . . .
7.3.3 Station Status Diagnostics 7-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents

vii
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
7.3.4 Manufacturer Identification Diagnostics 7-17. . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.5 Device-related Diagnostics – Digital ET 200C 7-18. . . . . . . . . . . . . . . . . . . . .
8 Fault Diagnostics with the IM 308-C 8-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Using LEDs to Diagnose Problems 8-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Using STEP 5 to Diagnose Problems (Station Diagnostics) 8-6. . . . . . . . .
8.2.1 Diagnosing the station status 8-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.2 Diagnosing the Manufacturer Identification 8-17. . . . . . . . . . . . . . . . . . . . . . .
8.2.3 Device-related Diagnostics – Digital ET 200C 8-18. . . . . . . . . . . . . . . . . . . . .
8.2.4 Identification- and Device-related Diagnostics – Analog ET 200C 8-21. . . .
9 Connection of the ET 200 Handheld 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1 Connection of the ET 200 Handheld 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 General Technical Specifications 10-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1 Overview of Digital and Analog Modules for the ET 200C 10-2. . . . . . . . . . .
10.2 General Technical Specifications 10-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Digital Modules 11-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1 Digital Input Module ET 200C; DI 8 DC 24V
(6ES7 141-0BF00-0BX0) 11-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 Digital Output Module ET 200C; DO 8 DC 24V/0.5A
(6ES7 142-0BF00-0XB0) 11-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 Digital Output Module ET 200C; DO 8 DC 24V/2A
(6ES7 142-0BF10-0XB0) 11-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24V/2A
(6ES7 143-0BL00-0XB0 and 6ES7 143-0BL10-0XB0) 11-16. . . . . . . . . . . . .
12 Analog Modules 12-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1 Analog Input Module ET 200C; AI 4/8 12 Bit
(6ES7 144-0KH00-0XB0) 12-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2 ET 200C Analog Input Module; AI 4 12 Bit
(6ES7 144-0HF00-0XB0) 12-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.3 ET 200C Analog Output Module; AO 4 12 Bit
(6ES7 145-0HF00-0XB0) 12-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 Other ET 200C Components 13-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1 T Connector (6ES5 762-2CT11) 13-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2 Power Supply Connector (6ES5 762-2CS11) 13-3. . . . . . . . . . . . . . . . . . . . .
13.3 Programmer Connector (6ES5 762-2CA12) 13-5. . . . . . . . . . . . . . . . . . . . . .
13.4 Cables 13-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5 Terminating Resistor (6ES5 755-2CA11) 13-8. . . . . . . . . . . . . . . . . . . . . . . . .
13.6 Adapter Cable (6ES5 755-8CA11) 13-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents

viii ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
A Pin Assignments of the ET 200C Modules A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1 Pin Assignments of ET 200C Digital Modules A-2. . . . . . . . . . . . . . . . . . . . .
A.2 Pin Assignments of ET 200C Analog Modules A-5. . . . . . . . . . . . . . . . . . . .
B Type Files B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.1 Type Files, ET 200C Digital Modules for COM ET 200 V4.x B-2. . . . . . . . .
B.1.1 Type File SN8010TD.200: COM ET 200 V4.x - C-8DI DP B-3. . . . . . . . . . .
B.1.2 Type File SN8011TD.200: COM ET 200 V4.x - C-8DO DP B-4. . . . . . . . . .
B.1.3 Type File SN8012TD.200: COM ET 200 V4.x - C-8DO/2A DP B-5. . . . . . .
B.1.4 Type File SN8013TD.200: COM ET 200 V4.x - C-16DI/16DO/2A DP B-6.
B.2 Type Files of ET 200C Analog Modules for COM ET 200 Windows B-7. .
B.2.1 Type File SI800FAD.200: COM ET 200 Windows - C-4/8AI DP B-8. . . . . .
B.2.2 Type File SI800EAD.200: COM ET 200 Windows - C-4AI DP B-13. . . . . . .
B.2.3 Type File SI800DAD.200: COM ET 200 Windows - C-4AO DP B-16. . . . . .
C Safety-Related Guidelines C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C.1 Active and Passive Faults in Automation Equipment C-2. . . . . . . . . . . . . . .
C.2 Suggestions for Configuring and Installing a Distributed I/O Station C-3. .
Contents

ix
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Figures
1-1 ET 200 Bus Users Described in this Manual 1-2. . . . . . . . . . . . . . . . . . . . . .
1-2 ET 200C Digital and Analog Modules 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3 Other ET 200C Components 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1 Legend 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 SINEC L2-DP Field Bus and Power Supply Looped Through
at ET 200C Slave Station 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3 SINEC L2-DP Field Bus and Power Supply Looped Through
with T Connectors 2-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4 Rule for Use of a T Connector 2-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5 Configuration using Several Power Supply Connectors 2-11. . . . . . . . . . . .
2-6 SINEC L2-DP Field Bus Looped Through with T Connectors –
Individual External Power Supply to Each Slave Station 2-13. . . . . . . . . . . .
2-7 Rules for Use of a T Connector 2-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8 Rules for Current Connection 2-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-9 Configuration with Programmer Connector 2-16. . . . . . . . . . . . . . . . . . . . . . .
3-1 Digital Input Module ET 200C; DI 8 DC 24V
(6ES7 141-0BF00-0XB0) 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Digital Output Module ET 200C; DO 8 DC 24V/0.5A
(6ES7 142-0BF00-0XB0) 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3 Digital Output Module ET 200C; DO 8 DC 24V/2A
(6ES7 142-0BF10-0XB0) 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24V
with Circular Connector
(6ES7 143-0BL00-0XB0) 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5 Digital I/O Module ET 200C; DI 16/DO 16 DC 24 V with
Conduit Thread Glands (6ES7 143-0BL10-0XB0) 3-10. . . . . . . . . . . . . . . . .
3-6 Analog Input Module ET 200C; AI 4/8 12 Bit
(6ES7 144-0KH00-0XB0) 3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7 Analog Input Module ET 200C; AI 4 12 Bit
(6ES7 144-0HF00-0XB0) 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8 Analog Output Module ET 200C; AO 4 12 Bit
(6ES7 145-0HF00-0XB0) 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9 T Connector 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-10 Power Supply Connector 3-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11 Programmer Connector 3-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-12 Terminating Resistor 3-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-13 Adapter Cable 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1 Grounded Configuration for ET 200C with 24 V DC
Current/Load Voltage Supply 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2 Ungrounded Configuration for ET 200C 4-7. . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Bus Connections of the ET 200C Modules 4-10. . . . . . . . . . . . . . . . . . . . . . .
4-4 Sensor Supply Returned to Input without Load 4-14. . . . . . . . . . . . . . . . . . . .
4-5 Sensor Supply Returned to Input with Load 4-14. . . . . . . . . . . . . . . . . . . . . . .
4-6 Output Returned to Input without Load 4-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7 Output Returned to Input with Load 4-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8 Output Returned to Input without Load 4-18. . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9 Output Returned to Input with Load 4-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10 Arrangement of Screw Terminals of ET 200C;
DI 16/DO 16 DC 24V/2A (6ES7 143-0BL10-0XB0) 4-20. . . . . . . . . . . . . .
4-11 Components of the Cable Gland for the Grounding Cable 4-21. . . . . . . . . .
Contents

xET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
4-12 Arrangement of Screw Terminals and DIL Switches in ET 200C;
AI 4/8 12 Bit 4-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-13 Connection to ET 200C; AI 4/8 12 Bit of Thermocouples
for Floating Measurement and External Floating Compensation 4-24. . . . .
4-14 Connection to ET 200C; AI 4/8 12 Bit of Thermocouples for
Non-Floating Measurement and External Non-Floating Compensation 4-25
4-15 Connection to ET 200C; AI 4/8 12 Bit of Thermocouples for
Non-Floating Measurement and Internal Compensation 4-26. . . . . . . . . . . .
4-16 Connection to ET 200C; AI 4/8 12 Bit of Resistance Thermometers
(Pt 100) in 2-Wire Circuit for Floating Measurement 4-27. . . . . . . . . . . . . . .
4-17 Connection to ET 200C; AI 4/8 12 Bit of Resistance Thermometers
(Pt 100) in 4-Wire Circuit for Floating Measurement 4-28. . . . . . . . . . . . . . .
4-18 Connection to ET 200C; AI 4/8 12 Bit of Voltage Sensors
in 2-Wire Circuit for Non-Floating Measurement 4-29. . . . . . . . . . . . . . . . . . .
4-19 Components of the Cable Gland for the Grounding Cable 4-30. . . . . . . . . .
4-20 Arrangement of Screw Terminals and DIL Switches in ET 200C;
AI 4 12 Bit 4-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-21 Connection to ET 200C; AI 4 12 Bit of Voltage Sensors
in 2-Wire Circuit for Floating Measurement 4-33. . . . . . . . . . . . . . . . . . . . . . .
4-22 Connection to ET 200C; AI 4 12 Bit of Current Sensors
in 2-Wire Circuit for Floating Measurement 4-34. . . . . . . . . . . . . . . . . . . . . . .
4-23 Components of the Cable Gland for the Grounding Cable 4-35. . . . . . . . . .
4-24 Arrangement of Screw Terminals and DIL Switches in ET 200C;
AO 4 12 Bit 4-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-25 Connection of Loads to ET 200C; AO 4 12 Bit, 4-Wire Circuit
for Voltage Output 4-38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-26 Connection of Loads to ET 200C; AO 4 12 Bit, 2-Wire Circuit
for Voltage Output 4-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-27 Connection of Loads to ET 200C; AO 4 12 Bit, 2-Wire Circuit
for Current Output 4-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-28 DIL Switch Block in Default Position (As Delivered) 4-44. . . . . . . . . . . . . . . .
4-29 Example of How to Set a Station Number at DIL Switch
Block S1 4-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-30 Block Diagram of DIL Switches in DIL Switch Block S2 4-47. . . . . . . . . . . . .
4-31 Block Diagram of DIL Switches in DIL Switch Block S4 4-49. . . . . . . . . . . . .
4-32 Block Diagram of DIL Switches in DIL Switch Block S5 4-51. . . . . . . . . . . . .
5-1 “CONFIGURING” Screen (1) 5-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2 “CONFIGURING” Screen (2) 5-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3 ”CONFIGURING” Screen (3) 5-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-4 Structure of the Parameterization Frame for ET 200C: Byte 0 5-13. . . . . . .
5-5 Structure of the Parameterization Frame for ET 200C: Byte 1 5-13. . . . . . .
6-1 Connecting the Programmer to the ET 200C 6-2. . . . . . . . . . . . . . . . . . . . . .
6-2 Connecting the Programmer to the SINEC L2-DP Field Bus 6-3. . . . . . . .
6-3 “SYSTEM START-UP/TEST: STATION SELECTED” Screen 6-5. . . . . . . .
6-4 ”SYSTEM START-UP/TEST: STATUS/CONTROL” Screen 6-7. . . . . . . . . .
7-1 ”INDIVIDUAL DIAGNOSTICS” Screen 7-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2 Structure of the Diagnostics Word after Requesting the
Diagnostics ”Overview” 7-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3 Structure of the Diagnostics Word after Requesting the
Diagnostics for ”Parameter Assignment and Addressability” 7-13. . . . . . . .
7-4 Structure of the Diagnostics Word after Requesting the Station
Status (Station Status 1 and Station Status 2) 7-15. . . . . . . . . . . . . . . . . . . .
Contents

xi
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
7-5 Structure of the Diagnostics Word after Requesting the
Station Status (Station Status 3 and Master Address) 7-16. . . . . . . . . . . . . .
7-6 Structure of the Diagnostics Word after Request for Manufacturer
Identification 7-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7 Structure of the Diagnostics Word after Requesting the Header
and the Device-related Diagnostics of ET 200C;
DI 16/DO 16 DC 24V/2A 7-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8 Structure of the Diagnostics Word after Requesting the
Device-related Diagnostics of ET 200C; DI 8 DC 24V, ET 200C;
DO 8 DC 24V/0.5A and ET 200C; DO 8 DC 24V/2A 7-20. . . . . . . . . .
8-1 Diagram Illustrating How Station Diagnostics is Requested
with FB IM308C 8-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2 Structure of the Diagnostics Word (Station Status 1 and
Station Status 2) 8-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3 Structure of the Diagnostics Word ”Station Status 3 and
Master Station Number” 8-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4 Structure of the ”Manufacturer Identification” Diagnostics Word 8-17. . . . .
8-5 Structure of the Diagnostics Word ”Header and Device-related
Diagnostics” of ET 200C; DI 16/DO 16 DC 24V 8-19. . . . . . . . . . . . . . . . .
8-6 Structure of the Diagnostics Word for ”Device-related Diagnostics”
for ET 200C; DI 8 DC 24V; ET 200C; DO 8 DC 24V/0.5A and
ET 200C; DO 8 DC 24V/2A 8-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-7 Structure of Diagnostics Word for Identification-related Diagnostics
(DW n + 3) for Analog ET 200C Modules 8-24. . . . . . . . . . . . . . . . . . . . . . . . .
8-8 Structure of Diagnostics Word ”Header – Device-related Diagnostics”
(DW n + 4) for Analog ET 200C Modules 8-25. . . . . . . . . . . . . . . . . . . . . . . . .
8-9 Structure of Diagnostics Word ”Device-related Diagnostics –
Diagnostics Alarm” (DW n + 5) for Analog ET 200C Modules 8-25. . . . . . .
8-10 Structure of Diagnostics Word ”Device-related Diagnostics –
Diagnostics Alarm” (DW n + 6) for Analog ET 200C Modules 8-26. . . . . . .
8-11 Structure of Diagnostics Word ”Device-related Diagnostics –
Diagnostics Alarm” (DW n + 7) for Analog ET 200C Modules 8-26. . . . . . .
8-12 Structure of Diagnostics Word ”Device-related Diagnostics –
Diagnostics Alarm” (DW n + 8) for Analog ET 200C Modules 8-27. . . . . . .
8-13 Structure of Diagnostics Word ”Device-related Diagnostics –
Diagnostics Alarm” (DW n + 9) for Analog ET 200C Modules 8-27. . . . . . .
8-14 Structure of Diagnostics Word ”Header and Device-related
Diagnostics – Diagnostics Alarm” (DW n + 10)
for Analog ET 200C Modules 8-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-15 Structure of Diagnostics Word ”Header and Device-related
Diagnostics – Diagnostics Alarm” (DW n + 12)
for Analog ET 200C Modules 8-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-16 Structure of Diagnostics Word ”Device-related Diagnostics –
Limit Value Alarm” (DW n + 6) for Analog ET 200C Modules 8-30. . . . . . . .
9-1 Connection of ET 200 Handheld for Configuration with Power Supply
Connector and without T Connector 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2 Connection of ET 200 Handheld for Configuration with External
Power Supply 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-3 Connection of the Handheld to the Unassigned Bus Connection
of the ET 200C Station for Configuration with
Power Supply Connector and T Connector 9-4. . . . . . . . . . . . . . . . . . . . . . .
Contents

xii ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
9-4 Connection of the Handheld to the T Connector for Configuration
with Power Supply Connector and T Connector 9-4. . . . . . . . . . . . . . . . . . .
11-1 Digital Input Module ET 200C; DI 8 DC 24V: Block Diagram 11-3. . . . . .
11-2 Digital Input Module ET 200C; DI 8 DC 24 V;
Dimension Drawing 11-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-3 Digital Input Module ET 200C; DI 8 DC 24 V; Dimension Drawing
with T Connector and Plug Connectors (with Pin/Socket Inserts) 11-5. . . .
11-4 Digital Output Module ET 200C; DO 8 DC 24V/0.5A:
Block Diagram 11-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-5 Digital Output Module ET 200C; DO 8 DC 24 V/0.5A;
Dimension Drawing 11-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-6 Digital Output Module ET 200C; DO 8 DC 24 V/0.5A;
Dimension Drawing with T Connector and Plug Connectors
(with Pin/Socket Inserts) 11-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-7 Digital Output Module ET 200C; DO 8 DC 24V/2A:
Block Diagram 11-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-8 Digital Output Module ET 200C; DO 8 DC 24 V/2A;
Dimension Drawing 11-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-9 Digital Output Module ET 200C; DO 8 DC 24 V/2A;
Dimension Drawing with T Connector and Plug Connectors
(with Pin/Socket Inserts) 11-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-10 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24V/2A:
Block Diagram 11-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-11 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24 V/2A
(6ES7 143-0BL00-0XB0); Dimension Drawing 11-20. . . . . . . . . . . . . . . . . . . .
11-12 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24 V/2A
(6ES7 143-0BL10-0XB0); Dimension Drawing 11-21. . . . . . . . . . . . . . . . . . . .
11-13 Digital Input/Output Module ET 200C; DI 16/DO 16 DC 24 V/2A
(6ES7 143-0BL00-0XB0); Dimension Drawing with T Connector
and Plug Connectors (with Pin/Socket Inserts) 11-22. . . . . . . . . . . . . . . . . . . .
11-14 Digital Input/Output Module ET 200C; DI16/DO 16 DC 24 V/2A
(6ES7 143-0BL10-0XB0); Dimension Drawing with T Connector
and Plug Connectors (with Pin/Socket Inserts) 11-23. . . . . . . . . . . . . . . . . . . .
12-1 ET200C Analog Input Module; AI 4/8 12 Bit: Block Diagram 12-4. . . . . .
12-2 Screw Terminals and Their Assignments in the ET 200C;
AI 4/8 12 Bit 12-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-3 ET 200C Analog Input Module; AI 4/8 12 Bit:
Dimensional Drawing 12-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-4 ET 200C Analog Input Module; AI 4/8 12 Bit:
Dimensional Drawing with T-connector 12-19. . . . . . . . . . . . . . . . . . . . . . . . . . .
12-5 ET200C Analog Input Module; AI 4 12 Bit: Block Diagram 12-21. . . . . . .
12-6 Screw Terminals with Assignments in the ET 200C; AI 4 12 Bit 12-21. . .
12-7 ET 200C Analog Input Module; AI 4 12 Bit:
Dimensional Drawing 12-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-8 ET 200C Analog Input Module; AI 4 12 Bit:
Dimensional Drawing with T-connector 12-32. . . . . . . . . . . . . . . . . . . . . . . . . . .
12-9 ET 200C Analog Output Module; AO 4 12 Bit: Block Diagram 12-34. . . .
12-10 Screw Terminals with Assignments in the ET 200C;
AO 4 12 Bit 12-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents

xiii
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
12-11 ET 200C Analog Output Module;AO 4 12 Bit:
Dimensional Drawing 12-42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-12 ET 200C Analog Output Module; AO 4 12 Bit:
Dimensional Drawing with T-connector 12-43. . . . . . . . . . . . . . . . . . . . . . . . . . .
13-1 Power Supply Connector: Dimension Drawing with Plug Connectors
(with Pin/Socket Insert) 13-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-2 Power Supply Connector: Dimension Drawing 13-4. . . . . . . . . . . . . . . . . . . .
13-3 Programmer Connector: Dimension Drawing with Plug Connectors
(with Pin/Socket Insert) 13-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-4 Programmer Connector: Dimension Drawing 13-6. . . . . . . . . . . . . . . . . . . . .
Contents

xiv ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Tables
1-1 Maximum baud rates with components of ET 200C 1-6. . . . . . . . . . . . . . . .
1-2 Length of the SINEC L2 Bus Cable in Accordance
with the Baud Rate on the SINEC L2-DP Bus 1-7. . . . . . . . . . . . . . . . . . . . .
2-1 ET 200C Configuration Options 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 Permissible Current Load for Load Voltage Supply 2-6. . . . . . . . . . . . . . . .
2-3 Permissible Current Load for Load Voltage Supply 2-9. . . . . . . . . . . . . . . .
2-4 Length of the Bus Cable, if SINEC L2-DP Field Bus
and Power Supply are Combined in One Cable 2-10. . . . . . . . . . . . . . . . . . .
2-5 Current Consumption of the Digital Modules of ET 200C 2-10. . . . . . . . . . .
2-6 Permissible Current Load for Load Voltage Supply 2-14. . . . . . . . . . . . . . . .
2-7 Length of the Spur Line of the Programmer Connection
in Accordance with the Baud Rate on the SINEC L2-DP Bus 2-17. . . . . . . .
3-1 ET 200C Cables 3-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Order Numbers for Standard Cable Lengths (Core Cross-Sectional
Area 0.75 mm2/Max. Current Load 4 A) 3-21. . . . . . . . . . . . . . . . . . . . . . . . . .
3-3 Order Numbers for Standard Cable Lengths (Core Cross-Sectional
Area 0.75 mm2/Max. Current Load 4 A) 3-21. . . . . . . . . . . . . . . . . . . . . . . . . .
4-1 Distances between ET 200C Modules and Cable Ducts 4-2. . . . . . . . . . . .
4-2 Order Numbers for Circular Connectors 4-8. . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Pin Assignment of the Bus Connection where only the SINEC L2-DP
is Connected 4-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4 Pin Assignment of the Bus Connection where only the Power Supply
is Connected 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5 Pin Assignment of the Bus Connection if SINEC L2-DP and
Power Supply are Connected 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6 Pin Assignment of the Inputs of ET 200C; DI 8 DC 24V
(6ES7 141-0BF00-0XB0) 4-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7 Pin Assignments of the Outputs of ET 200C; DO 8 DC 24V/0.5A
(6ES7 142-0BF00-0XB0) and ET 200C; DO 8 DC 24V/2A
(6ES7 142-0BF10-0XB0) 4-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8 Pin Assignments of the Inputs of ET 200C;
DI 16/DO 16 DC 24V/2A (6ES7 143-0BL00-0XB0) 4-17. . . . . . . . . . . . . .
4-9 Pin Assignments of the Outputs of ET 200C;
DI 16/DO 16 DC 24V/2A (6ES7 143-0BL00-0XB0) 4-17. . . . . . . . . . . . . .
4-10 Connection Assignments of ET 200C; DI 16/DO 16 DC 24V/2A
(6ES7 143-0BL10-0XB0) 4-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11 Connection Assignment of the Inputs of ET 200C; AI 4/8 12 Bit
(6ES7 144-0KH00-0KB0) 4-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-12 DIL-Switch blocks in the ET 200C; AI 4/8 12 Bit 4-23. . . . . . . . . . . . . . . .
4-13 Connection Assignment of the Inputs of ET 200C; AI 4 12 Bit
(6ES7 144-0HF00-0KB0) 4-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-14 DIL Switch Blocks in ET 200C; AI 4 12 Bit 4-32. . . . . . . . . . . . . . . . . . . . .
4-15 Pin Assignment, Outputs of ET 200C; AO 4 12 Bit
(6ES7 145-0HF00-0XB0) 4-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-16 DIL Switch Blocks in ET 200C; AO 4 12 Bit 4-37. . . . . . . . . . . . . . . . . . . .
4-17 Pin Assignment of the Load Voltage Supply 4-41. . . . . . . . . . . . . . . . . . . . . .
4-18 Pin Assignment of the External Power Supply 4-42. . . . . . . . . . . . . . . . . . . . .
4-19 Module-Specific DIL Switch Blocks in ET 200C; AI 4/8 12 Bit 4-46. . . . .
4-20 DIL Switches in DIL Switch Block S2 4-47. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-21 DIL Switches in DIL Switch Block S3 4-48. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-22 DIL Switches in DIL Switch Block S4 4-49. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents

xv
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
4-23 Module-Specific DIL Switch Block in ET 200C; AI 4 12 Bit 4-50. . . . . . . .
4-24 DIL Switches in DIL Switch Block S5 4-51. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-25 Module-specific DIL-switch block in ET 200C; AO 4 12 Bit 4-52. . . . . . .
4-26 DIL Switches in DIL Switch Block S2 4-53. . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1 Type File Designations for ET 200C 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2 Address Identifiers for ET 200C (DP Standard) 5-8. . . . . . . . . . . . . . . . . . .
7-1 Fault Messages through LEDs on the ET 200C; DI 8 DC 24V 7-2. . . .
7-2 Fault Messages through LEDs of the ET 200C;
DO 8 DC 24V/0.5A and ET 200C; DO 8 DC 24V/2A 7-3. . . . . . . . . .
7-3 Fault Messages through LEDs of the ET 200C;
DI 16/DO 16 DC 24V/2A 7-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4 STEP 5 Diagnostics Facilities 7-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5 Structure of the Station Diagnostics for ET 200C 7-8. . . . . . . . . . . . .
7-6 Combination of the Diagnostics ”Overview” and Diagnostics
for ”Parameter Assignment and Addressability” 7-13. . . . . . . . . . . . . . . . . . .
8-1 Fault Messages through LEDs on the ET 200C; DI 8 DC 24V 8-2. . . .
8-2 Fault Messages through LEDs of the ET 200C;
DO 8 DC 24V/0.5A and ET 200C; DO 8 DC 24V/2A 8-3. . . . . . . . . .
8-3 Fault Messages through LEDs of the ET 200C;
DI 16/DO 16 DC 24V/2A 8-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4 Fault Messages through LEDs of the ET 200C; AI 4/8 12 Bit,
AI 4 12 Bit and AO 4 12 Bit 8-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-5 STEP 5 Diagnostics Facilities, Operation with IM 308-C 8-6. . . . . . . . . . . .
8-6 Structure of Station Diagnostics for Digital ET 200C Modules 8-7. . . . . . .
8-7 Structure of Station Diagnostics for ET 200C; AI 4/8 12 Bit 8-8. . . . . . .
8-8 Structure of Station Diagnostics for ET 200C; AI 4 12 Bit 8-9. . . . . . . .
8-9 Structure of Station Diagnostics for ET 200C; AO 4 12 Bit 8-10. . . . . . .
8-10 Position of the Diagnostics Data in the Data Block 8-14. . . . . . . . . . . . . . . . .
8-11 Position of Diagnostics Data in Data Block for ET 200C
(digital ET 200C) 8-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-12 Position of Diagnostics Data in Data Block for ET 200C;
AI 4/8 12 Bit 8-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-13 Position of the Diagnostics Data in the Data Block for ET 200C;
AI 4 12 Bit 8-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-14 Position of the Diagnostics Data in the Data Block for ET 200C;
AO 4 12 Bit 8-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-1 Parameters for Digital Input Module ET 200C; DI 8 DC 24 V 11-3. . . . .
11-2 Parameters for Digital Output Module ET 200C;
DO 8 DC 24 V/0.5A 11-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-3 Parameters for Digital Output Module ET 200C;
DO 8 DC 24 V/2A 11-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-4 Parameters for Digital Input/Output Module ET 200C;
DI 16/DO 16 DC 24 V/2A 11-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-1 Parameters for ET 200C Analog Input Module; AI 4/8 12 Bit 12-5. . . . . .
12-2 Parameters for ET 200C Analog Input Module; AI 4/8 12 Bit:
Range of Values, Bytes 25 to 28 12-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-3 Presentation of an Analog Input Value as Bit Pattern for SIMATIC S5
with ET 200C; AI 4/8 12 Bit 12-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-4 Description of Bit for ET 200C; AI 4/8 12 Bit 12-8. . . . . . . . . . . . . . . . . . . .
12-5 Digitized Measured Values for ET 200C; AI 4/8 12 Bit
(Measuring Ranges:"80 mV,"250 mV, "500 mV and
"1000 mV) 12-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents

xvi ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
12-6 Digitized Measured Values for ET 200C; AI 4/8 12 Bit with
Resistance Sensors 12-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-7 Digitized Measured Values for ET 200C; AI 4/8 12 Bit with
Linearization; Type K Thermocouple (Nickel-Chromium/
Nickel-Aluminum, to IEC 584) 12-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-8 Digitized Measured Values for ET 200C; AI 4/8 12 Bit with
Linearization; Type J Thermocouple (Iron/Copper-Nickel
(Constantan), to IEC 584) 12-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-9 Digitized Measured Values for ET 200C; AI 4/8 12 Bit
with Linearization; Type L Thermocouple (Iron/Copper-Nickel
(Constantan), to DIN 43710) 12-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-10 Presentation of an Analog Input Value as Bit Pattern for SIMATIC S7
with ET 200C; AI 4/8 12 Bit 12-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-11 Digitized Measured Values for ET 200C; AI 4/8 12 Bit
(Measuring Ranges: "80 mV, "250 mV, "500 mV and
"1000 mV) 12-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-12 Digitized Measured Values for ET 200C; AI 4/8 12 Bit for Pt 100
Resistance Sensors 12-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-13 Digitized Measured Values for ET 200C; AI 4/8 12 Bit for Type K
Thermocouple 12-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-14 Digitized Measured Values for ET 200C; AI 4/8 12 Bit for Type N
Thermocouple 12-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-15 Digitized Measured Values for ET 200C; AI 4/8 12 Bit for Type J
Thermocouple 12-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-16 Digitized Measured Values for ET 200C; AI 4/8 12 Bit for Type E
Thermocouple 12-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-17 Parameters for ET 200C Analog Input Module; AI 4 12 Bit 12-22. . . . . . .
12-18 Presentation of an Analog Input Value as Bit Pattern for ET 200C;
AI 4 12 Bit 12-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-19 Description of bits for ET 200C; AI 4 12 Bit 12-24. . . . . . . . . . . . . . . . . . . . .
12-20 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Ranges: "1.25 V, "2.5 V, "5 V, "10 V) 12-25. . . . . . . . . . .
12-21 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Range: "20 mA) 12-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-22 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Range: 0 ... 20 mA) 12-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-23 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Range: 4 ... 20 mA) 12-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-24 Presentation of an Analog Input Value as Bit Pattern for SIMATIC S7
with ET 200C; AI 4 12 Bit 12-28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-25 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Ranges: "1.25 V, "2.5 V, "5 V and "10 V) 12-28. . . . . . .
12-26 Digitized Measured Values for ET 200C;
AI 4 12 Bit (Measuring Range: "20 mA) 12-29. . . . . . . . . . . . . . . . . . . . . .
12-27 Digitized Measured Values for ET 200C; AI 4 12 Bit
(Measuring Ranges: 0 to 20 mA and 4 to 20 mA) 12-30. . . . . . . . . . . . . . . . . .
12-28 Parameters for ET 200C Analog Output Module; AO 4 12 Bit 12-35. . . . .
12-29 Substitute Value Output of ET 200C; AO 4 12 Bit on Interruption
in Communication 12-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-30 Presentation of an Analog Input Value as Bit Pattern for ET 200C;
AO 4 12 Bit 12-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-31 Description of bits for ET 200C; AO 4 12 Bit 12-37. . . . . . . . . . . . . . . . . . . .
Contents

xvii
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
12-32 Analog Output Signals of ET 200C; AO 4 12 Bit
(Ranges of Values: "10 V, 0 ... 10 V, "20 mA, 0 ... 20 mA,
4 ... 20 mA) 12-38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-33 Presentation of an Analog Input Value as Bit Pattern for SIMATIC S7
with ET 200C; AO 4 12 Bit 12-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-34 Digitized Measured Values for ET 200C; AO 4 12 Bit
(Output Ranges: "20 mA, 0 to 20 mA and 4 to 20 mA) 12-40. . . . . . . . . . . .
12-35 Digitized Measured Values for ET 200C; AO 4 12 Bit
(Output Ranges: 0 to 10 V and "10 V) 12-41. . . . . . . . . . . . . . . . . . . . . . . . . .
A-1 Pin Assignment of Bus Connector for ET 200 C Digital Modules,
only SINEC L2-DP Connected A-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-2 Pin Assignment of Bus Connector for ET 200C Digital Modules,
only Separate Power Supply Connected A-2. . . . . . . . . . . . . . . . . . . . . . . . .
A-3 Pin Assignment of Bus Connector for ET 200C Digital Modules,
SINEC L2-DP and Power Supply Combined in a Common Cable A-2. . . .
A-4 Pin Assignment, Inputs of ET 200C; DI 8 DC 24V and ET 200C;
DI 16/DO 16 DC 24V/2A (6ES7 143-0BL00-0BX0) A-3. . . . . . . . . . . . . .
A-5 Pin Assignment, Outputs of ET 200C; DO 8 DC 24V/0.5A,
ET 200C; DO 8 DC 24V/2A and ET 200C;
DI16/DO16 DC 24V/2A (6ES7 143- 0BL00-0XB0) A-3. . . . . . . . . . . . . .
A-6 Pin Assignment, Inputs and Outputs of ET 200C;
DI 16/DO 16 DC 24V/2A (6ES7 143-0BL10-0XB0) A-3. . . . . . . . . . . . . .
A-7 Pin Assignment for Load Voltage Supply, ET 200C Modules
with Outputs A-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-8 Pin Assignment, External Power Supply at PSU Feed A-4. . . . . . . . . . . . . .
A-9 Pin Assignment of Bus Connector for ET 200C Analog Modules,
only SINEC L2-DP Connected A-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-10 Pin Assignment of Bus Connector for ET 200C Analog Modules,
only Separate Power Supply Connected A-5. . . . . . . . . . . . . . . . . . . . . . . . .
A-11 Pin Assignment of Bus Connector for ET 200C Analog Modules,
SINEC L2-DP and Power Supply Combined in a Common Cable A-5. . . .
A-12 Pin Assignment, Inputs of ET 200C; AI 4/8 12 Bit
(6ES7 144-0KH00-0XB0) A-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-13 Pin Assignment, Inputs of ET 200C; AI 4 12 Bit
(6ES7 144-0HF00-0XB0) A-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-14 Pin Assignment, Outputs of ET 200C; AO 4 12 Bit
(6ES7 145-0HF00-0XB0) A-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B-1 Designations of Type Files for ET 200C Digital Modules B-2. . . . . . . . . . . .
B-2 Designations of Type Files for ET 200C Analog Modules B-7. . . . . . . . . . .
Contents

xviii ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Contents

1-1
ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
Configuration
This chapter ”Configuration” provides you with information on
the position of the ET 200C distributed I/O station in the distributed I/O
system and
the components of the ET 200C.
In this Chapter
1

1-2 ET 200C Distributed I/O Station
EWA 4NEB 812 6119-02b
1.1 What is the ET 200?
The distributed I/O system ET 200 is based on the PROFIBUS standard
(DIN 19245, Part 1) and the PROFIBUS-DP draft standard (DIN 19245,
Part 3).
At SIEMENS, the PROFIBUS is called SINEC L2.
The field bus on which the ET 200 distributed I/O system is based, is a variant
of SINEC L2 called SINEC L2-DP. This version is designed for communication
with the distributed I/O at extremely short response times.
The distributed I/O system comprises active and passive stations, the
SINEC L2-DP field bus and the SINEC L2 network components. The
distributed I/O station is a slave station.
+
Other field
devices
SINEC L2-DP Field Bus
(2-wire or Fiber-Optic Cable)
ET 200CET 200B ET 200U
IM 308-B
IM 308-C
Figure 1-1 ET 200 Bus Users Described in this Manual
Definition
Stations Described
in this Manual
Configuration