Siemens SIMATIC ET 200eco PN User manual

SIMATIC Distributed I/O ET 200eco PN
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
_
_____________
Preface
Product overview
1
Installing
2
Wiring
3
Configuring
4
Commissioning
5
Maintenance
6
Interrupt, error, and system
messages
7
General technical data
8
I/O device digital
inputs/outputs
9
IO-Link Master
10
I/O device analog
input/output
11
Terminal block and voltage
distributor
12
Order numbers
A
Dimensional drawings
B
I/O address space
C
Response times for analog
input device and output
device
D
SIMATIC
Distributed I/O
ET 200eco PN
Operating Instructions
06/2009
A5E01250250-04

Legal information
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E01250250-04
Ⓟ 06/2009
Copyright © Siemens AG 2009.
Technical data subject to change

ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 3
Preface
Purpose of the manual
The information in this manual enables you to operate the ET 200eco PN distributed I/O
device on PROFINET IO as an IO Device.
Basic knowledge required
This manual presumes a general knowledge in the field of automation engineering.
The manual describes the components based on the data valid at the time of its release.
SIEMENS reserves the right of including a product information for each new component, and
for each component of a later version.
Scope of this manual
This manual applies to the ET 200eco PN distributed I/O device.
Changes compared to the previous version
The following modules were added:
● IO-Link Master 4 IO-L + 8 DI + 4 DO DC 24V/1,3A 8×M12
● I/O device 8 DIO DC 24V/1,3A 8×M12
● Voltage distributor PD DC 24V 1×7/8" 4×M12
CE Label
The SIMATIC S7 ET 200eco PN distributed I/O device product series fulfills the
requirements and safety objectives of the following EC directives.
● EC Directive 73/23/EEC "Low-voltage Directive"
● EC Directive 2004/108/EC "EMC Directive"
C-Tick-Mark
The SIMATIC S7 ET 200eco PN distributed I/O device product series fulfills the
requirements of AS/NZS 2064 (Australia and New Zealand).
Standards
The SIMATIC S7 ET 200eco PN distributed I/O device product series fulfills the
requirements and criteria of IEC 61131-2.
The ET 200eco PN distributed I/O device is based on IEC 61784-1:2002 Ed1 CP 3/1.

Preface
ET 200eco PN
4 Operating Instructions, 06/2009, A5E01250250-04
Scope of information
In addition to this manual, you need:
● The manual for the IO Controller you are using
● System manual SIMATIC PROFINET system description
(http://support.automation.siemens.com/WW/view/en/19292127)
● Programming manual Migration from PROFIBUS DP to PROFINET IO
(http://support.automation.siemens.com/WW/view/en/19289930)
Guide
This manual describes the hardware of the ET 200eco PN distributed I/O device. It consists
of instructive sections and reference sections (specifications).
Topics covered in this manual include
● Installing and wiring the ET 200eco PN distributed I/O device
● Commissioning and diagnostics of the ET 200eco PN distributed I/O device
● Components of the ET 200eco PN distributed I/O device
● Order numbers
● Important terms are explained in the glossary.
● The index helps you to quickly find all texts relevant to your keyword.
Recycling and disposal
ET 200eco PN can be recycled owing to its low pollutant content.
For ecologically compatible recycling and disposal of your old device, contact a certificated
disposal service for electronic scrap.
Additional support
If you have any further questions about the use of products described in this manual, and do
not find the right answers there, contact your local Siemens representative:
You can find your representative on the Internet
(http://www.automation.siemens.com/partner/guiwelcome.asp?lang=en).
A guide to the technical documentation for the various SIMATIC products and systems is
available on the Internet
(http://www.automation.siemens.com/simatic/portal/html_76/techdoku.htm).
The online catalog and ordering systems are available on the Internet
(http://mall.automation.siemens.com).
Training center
Siemens offers corresponding courses to get you started with your ET 200eco PN distributed
I/O device and the SIMATIC S7 automation system. Please contact your regional training
center or our main training center in Nuremberg, Germany, for details.
Additional information can be found on the Internet (http://www.sitrain.com/index_en.html).

Preface
ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 5
Technical Support
You can contact Technical Support for all A&D products by means of the Support Request
Web form on the Internet (http://www.siemens.de/automation/csi_en_WW/support_request).
Additional information about Siemens Technical Support is available on the Internet
(http://www.siemens.de/automation/csi_en_WW).
Service & Support on the Internet
In addition to our documentation, we offer a comprehensive knowledge base on the Internet
(http://www.siemens.de/automation/csi_en_WW).
There, you will find the following information:
● Our newsletter, providing the latest information on your products
● The right documents for your product on our Service & Support pages
● Worldwide forum in which users and experts exchange ideas
● Your local Automation & Drives partner in our partner database.
● Information about on-site services, repairs, spare parts, and lots more.

Preface
ET 200eco PN
6 Operating Instructions, 06/2009, A5E01250250-04

ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 7
Table of contents
Preface ...................................................................................................................................................... 3
1 Product overview ..................................................................................................................................... 11
1.1 Distributed I/O device – Overview................................................................................................11
1.2 ET 200eco PN Distributed I/O Device .........................................................................................12
2 Installing .................................................................................................................................................. 19
2.1 Installation without mounting rail..................................................................................................19
2.2 Installation with mounting rail.......................................................................................................22
2.3 Mounting position, mounting dimensions.....................................................................................22
2.4 Installing the terminal block..........................................................................................................23
2.5 Replacing labels...........................................................................................................................25
2.6 Removing ET 200eco PN ............................................................................................................26
3 Wiring ...................................................................................................................................................... 27
3.1 General rules and regulations for operating an ET 200eco PN...................................................27
3.2 Operating ET 200eco PN on grounded mains.............................................................................28
3.3 Electrical configuration of ET 200eco PN ....................................................................................31
3.4 Technical specifications of the lines ............................................................................................32
3.5 Wiring the ET 200eco PN ............................................................................................................33
3.5.1 Wiring the ET 200eco PN to functional earth (FE).......................................................................33
3.5.2 Wiring I/O devices........................................................................................................................34
3.6 Pin assignment of connectors......................................................................................................37
3.6.1 Pin assignment of the PROFINET connector ..............................................................................37
3.6.2 Pin assignment for feeding and looping the voltage....................................................................38
3.6.3 Pin assignment of digital inputs ...................................................................................................40
3.6.4 Pin assignment of digital outputs .................................................................................................42
3.6.5 Pin assignment for parameterizable digital input/output..............................................................46
3.6.6 Pin assignment for IO-Link Master...............................................................................................47
3.6.7 Pin assignment for analog input...................................................................................................49
3.6.8 Pin assignment for analog output ................................................................................................52
3.7 Wiring the terminal block..............................................................................................................53
3.8 Wiring the voltage distributor .......................................................................................................57
3.9 Looping PROFINET and the supply voltage................................................................................59

Table of contents
ET 200eco PN
8 Operating Instructions, 06/2009, A5E01250250-04
4 Configuring .............................................................................................................................................. 61
4.1 Configuring ET 200eco PN ......................................................................................................... 61
4.2 Configuring the IO-Link Master ................................................................................................... 62
4.3 Device names for ET 200eco PN................................................................................................ 64
4.4 Ports of ET 200eco PN ............................................................................................................... 65
4.5 Isochronous real-time communication ........................................................................................65
4.6 Prioritized startup ........................................................................................................................ 66
4.7 Device replacement without programming device ...................................................................... 66
4.8 Reset to factory settings.............................................................................................................. 67
4.9 SNMP.......................................................................................................................................... 67
5 Commissioning ........................................................................................................................................ 69
5.1 Commissioning ET 200eco PN ................................................................................................... 69
6 Maintenance ............................................................................................................................................ 71
6.1 Replacing the fuse ...................................................................................................................... 71
6.2 Online firmware update by means of STEP 7 Manager ............................................................. 72
6.3 Acyclic data exchange with the FB IOL_CALL............................................................................ 73
7 Interrupt, error, and system messages .................................................................................................... 75
7.1 Interrupts of ET 200eco PN......................................................................................................... 75
7.2 Maintenance interrupts................................................................................................................ 76
7.3 Diagnostics by means of LED display......................................................................................... 77
7.3.1 Diagnostics using the LED display on the I/O devices ............................................................... 77
7.3.2 Diagnostics using the LED display on the IO-Link Master.......................................................... 79
7.3.3 Diagnostics using the LED display at the voltage distributor...................................................... 80
7.4 Diagnostics messages of the I/O devices................................................................................... 81
7.5 Diagnostics with STEP 7............................................................................................................. 82
7.5.1 Reading diagnostics data............................................................................................................ 82
7.5.2 Channel diagnostics.................................................................................................................... 83
7.5.3 Error classes for I/O devices ....................................................................................................... 84
7.5.4 STOP of the IO Controller and recovery of the IO Device.......................................................... 86
8 General technical data............................................................................................................................. 87
8.1 Standards and certifications........................................................................................................ 87
8.2 EMC compatibility, shipping and storage conditions .................................................................. 88
8.3 Mechanical and climatic environmental conditions..................................................................... 90
8.4 Specification of dielectric tests, protection class, degree of protection, and rated voltage
of ET 200eco PN......................................................................................................................... 92

Table of contents
ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 9
9 I/O device digital inputs/outputs ............................................................................................................... 95
9.1 I/O device digital inputs................................................................................................................95
9.1.1 I/O device 8 DI 24 VDC 4xM12....................................................................................................95
9.1.2 I/O device 8 DI 24 VDC 8xM12....................................................................................................99
9.1.3 I/O device 16 DI 24 VDC 8xM12................................................................................................103
9.1.4 Parameter overview digital inputs..............................................................................................107
9.2 I/O device digital outputs............................................................................................................108
9.2.1 I/O device 8 DO 24 VDC/1.3A 4xM12 .......................................................................................108
9.2.2 I/O device 8 DO 24 VDC/0.5A 4xM12 .......................................................................................112
9.2.3 I/O device 8 DO 24 VDC/1.3A 8xM12 .......................................................................................116
9.2.4 I/O device 8 DO DC 24V/2,0A 8xM12 .......................................................................................120
9.2.5 I/O device 16 DO 24 VDC/1.3A 8xM12 .....................................................................................124
9.2.6 Parameter overview digital outputs............................................................................................128
9.3 I/O device digital inputs/outputs.................................................................................................130
9.3.1 I/O device 8 DIO DC 24V/1,3A 8xM12 ......................................................................................130
9.3.2 Parameter overview for digital inputs/outputs............................................................................135
10 IO-Link Master ....................................................................................................................................... 137
10.1 IO-Link Master............................................................................................................................137
10.2 Parameters for IO-Link Master...................................................................................................144
10.3 Functions....................................................................................................................................146
11 I/O device analog input/output ............................................................................................................... 147
11.1 I/O device analog input ..............................................................................................................147
11.1.1 I/O device 8 AI 4 U/I + 4 RTD/TC 8xM12...................................................................................147
11.1.2 Parameter overview analog input ..............................................................................................154
11.1.3 Parameter description analog input ...........................................................................................156
11.1.4 Analog value representation for measuring ranges with SIMATIC S7 ......................................160
11.1.5 Measuring ranges of the analog input device in S7 format .......................................................160
11.2 I/O device analog output............................................................................................................168
11.2.1 I/O device 4 AO U/I 4xM12 ........................................................................................................168
11.2.2 Parameter overview analog output ............................................................................................173
11.2.3 Parameter description analog output.........................................................................................174
11.2.4 Output ranges of analog output device......................................................................................175
11.3 Influence of the range of values.................................................................................................177
12 Terminal block and voltage distributor ................................................................................................... 179
12.1 Terminal block............................................................................................................................179
12.2 Voltage distributor ......................................................................................................................181
A Order numbers ...................................................................................................................................... 185
A.1 Order numbers...........................................................................................................................185
B Dimensional drawings............................................................................................................................ 189
B.1 Dimensional drawings................................................................................................................189

Table of contents
ET 200eco PN
10 Operating Instructions, 06/2009, A5E01250250-04
C I/O address space.................................................................................................................................. 195
C.1 I/O address space ..................................................................................................................... 195
D Response times for analog input device and output device ................................................................... 201
D.1 Response times for analog input device ................................................................................... 201
D.2 Response times for analog output device................................................................................. 202
Glossary ................................................................................................................................................ 205
Index...................................................................................................................................................... 211

Table of contents
ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 11

ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 13
Product overview 1
1.1 Distributed I/O device – Overview
Distributed I/O systems – application area
A plant configuration quite often features a process I/O configuration in a central automation
system.
The wiring of process I/O components installed at a grated distance away from an
automation system may soon may soon become highly complex and susceptible for
electromagnetic interference.
Distributed I/O systems are are the perfect solution for such configurations.
● The controller CPU is located in a central rack.
● The I/O systems (inputs and outputs) are operated locally in a distributed configuration.
What is PROFINET IO?
PROFINET IO is an open transmission system with real-time functionality defined in
accordance with the PROFINET standard. This standard defines a manufacturer-
independent communication, automation and engineering model.
Industrial-strength connections are available for wiring the PROFINET components.
● PROFINET discards the hierarchical PROFIBUS master/slave concept. and deploys a
provider/consumer principle instead. The IO Devices that will be subscribed to by an IO
Controller are defined within the planning phase.
● The quantity structures are extended in accordance with the available quantities for
PROFINET IO. Parameter limits are not exceeded during configuration.
● The transmission rate is 100 Mbps.
● The configuration interface for users is generally the same as that for PROFIBUS DP (the
system is configured in STEP 7 > HW Config).

Product overview
1.2 ET 200eco PN Distributed I/O Device
ET 200eco PN
14 Operating Instructions, 06/2009, A5E01250250-04
Structure of a PROFINET IO network
The figure below illustrates a typical PROFINET IO network structure. Existing PROFIBUS
slaves can be integrated using an IE/PB Link.
,2'HYLFH
(76
,2'HYLFH
(7HFR31
,2&RQWUROOHU
6
,(3%
OLQN
,QGXVWULDO
(WKHUQHW
23 3*
6ZLWFK 6ZLWFK
0D[P
6ZLWFK
352),1(7,2
352),%86'3
Figure 1-1 Typical structure of PROFINET IO
1.2 ET 200eco PN Distributed I/O Device
Definition
The ET 200eco PN distributed I/O device is a compact PROFINET IO device in degree of
protection IP 65/66 or IP 67 and UL Enclosure Type 4x, Indoor use only.
Field of application
The fields of application of the ET 200eco PN are derived from its special properties.
● A robust design and degree of protection IP 65/66 or IP 67 make the ET 200eco PN
distributed I/O device suitable in particular for use in rugged industrial environments.
● The compact design of the ET 200eco PN is particularly favorable for applications in
confined areas.
● The easy handling of ET 200eco PN facilitates efficient commissioning and maintenance.
Properties
The ET 200eco PN has the following properties:
● Integrated switch with 2 ports
● Supported Ethernet services:
– ping
– arp
– Network diagnostics (SNMP)
– LLDP
● Interrupts
– Diagnostics interrupts
– Maintenance interrupts
● Port diagnostics
● Isochronous real-time communication
● Prioritized startup
● Device replacement without programming device

Product overview
1.2 ET 200eco PN Distributed I/O Device
ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 15
Components of ET 200eco PN
The tables below provide an overview of the most important components of ET 200eco PN:
Table 1- 1 Components of ET 200eco PN
Component Function Figure
I/O device You connect the sensors and
actuators to the I/O device. The I/O
device is available in the following
variants:
8 DI DC 24V 4×M12
8 DI DC 24V 8×M12
16 DI DC 24V 8×M12
8 DO DC 24V/1,3A 4×M12
8 DO DC 24V/0,5A 4×M12
8 DO DC 24V/1,3A 8×M12
8 DO DC 24V/2,0A 8×M12
16 DO DC 24V/1,3A 8×M12
8 AI 4 U/I + 4 RTD/TC 8×M12
4 AO U/I 4×M12
8 DIO DC 24V/1,3A 8×M12




































① SF/MT LED ⑧ X03: Voltage infeed
② BF LED ⑨ X02: Loop-through of the voltage
③ ON LED ⑩ Input/output signal
④ DC 24V LED
(for digital output device only)
⑪ MAC address
⑤ P1 LK LED ⑫ X01 P2 LAN: PROFINET IO
connection
⑥ P2 LK LED ⑬ X01 P1 LAN: PROFINET IO
connection
⑦ Channel status/channel fault

Product overview
1.2 ET 200eco PN Distributed I/O Device
ET 200eco PN
16 Operating Instructions, 06/2009, A5E01250250-04
What is an IO-Link Master?
IO-Link is a point-to-point connection to conventional and intelligent sensors/actuators via
unshielded standard cable in proven 3-conductor technology. IO-Link Master is backwards
compatible with all DI/DO sensors/actuators. Switching state and data channel designed in
proven 24 VDC technology.
Supports mixed operation of sensors/actuators in the IO-Link, digital input and digital output
operating modes on all four ports of the IO-Link Master.
Table 1- 2 IO-Link Master
Component Function Figure
IO-Master Connect the following to I/O
device:
X1 to X4: IO-Link Devices or
sensors/actuators
X5, X6: Sensors
X7, X8: Actuators

















① SF/MT LED ⑩ X03: Voltage supply
② BF LED ⑪ X02: Looping of the voltage
③ ON LED ⑫ X7/X8: Output signal
④ DC 24V LED (only for digital output) ⑬ X5/X6: Input signal
⑤ P1 LK LED ⑭ MAC address
⑥ P2 LK LED ⑮ X1 to X4: IO-Link ports/input signal
⑦ Status display / Communication ⑯ X01 P2 LAN: PROFINET IO
connection
⑧ Digital input: Channel status/channel
fault
⑰ X01 P1 LAN: PROFINET IO
connection
⑨ Digital output: Channel status/channel
fault

Product overview
1.2 ET 200eco PN Distributed I/O Device
ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 17
Further components of ET 200eco PN
Table 1- 3 Further components of ET 200eco PN
Component Function Figure
Terminal block You can connect up to 10 A per
voltage to the terminal block for
distribution to the I/O devices. A
maximum of 4 A per voltage is
available short-circuit protected for
each I/O device.
Voltage
distributor
You can supply up to 8 A per
voltage at the
PD DC 24V 1×7/8" 4×M12 and
distribute up to 4 A per voltage and
connector short-circuit-protected
through 4 connectors.










① LEDs for routing 1L/2L
② LEDs for supply 1L/2L
③ X05: Status of voltage supply
④ X01 to X04: Looping of the voltage
Mounting rail You can install several I/O devices
on the mounting rail.

Product overview
1.2 ET 200eco PN Distributed I/O Device
ET 200eco PN
18 Operating Instructions, 06/2009, A5E01250250-04
IO Controller
The ET 200eco PN can communicate with all IO Controllers that conform to IEC 61158.
To configure an ET 200eco PN, you need
STEP 7 V5.4, SP4.
The ET 200eco PN can be configured starting from a CPU with extended diagnostics, FAQ
(https://support.automation.siemens.com/WW/view/en/23678970):
CPU Order number Firmware
version (or
higher)
Extended
diagnostics
Isochronous real-time
communication/prioritized
startup
CP1616 6GK1161-6AA00 V2.0 x -
CP1604 6GK1160-4AA00 V2.0 x -
CPU 414-3 PN/DP 6ES7414-3EM05-0AB0 V5.2 x x
CPU 416-3 PN/DP 6ES7416-3ER05-0AB0 V5.2 x x
CPU 416F-3 PN/DP 6ES7416-3FR05-0AB0 V5.2 x x
CPU 315-2 PN/DP 6ES7315-2EH13-0AB0 V2.5 x -
CPU 315F-2PN/DP 6ES7315-2FH13-0AB0 V2.5 x -
CPU 317-2 PN/DP 6ES7317-2EK13-0AB0 V2.5 x -
CPU 317F-2PN/DP 6ES7317-2FK13-0AB0 V2.5 x -
CPU 319-3 PN/DP 6ES7318-3EL00-0AB0 V2.7 x x
CPU 319F-3 PN/DP 6ES7318-3FL00-0AB0 V2.7 x x
CP343-1 Standard 6GK7343-1EX30-0XE0 V2.0 x -
CP343-1 Advanced 6GK7343-1GX30-0XE0 V1.0 x -
CP443-1 Standard 6GK7443-1EX20-0XE0 V1.0 x -
CP443-1 Advanced 6GK7443-1GX20-0XE0 V2.0 x -
IM151-8 PN/DP CPU 6ES7151-8AB00-0AB0 V2.7 x x
IM151-8F PN/DP CPU 6ES7151-8FB00-0AB0 V2.7 x x
IM154-8 CPU 6ES7154-8AB00-0AB0 V2.5 x -

ET 200eco PN
Operating Instructions, 06/2009, A5E01250250-04 19
Installing 2
Two installation variants
There are two installation variants:
● With mounting rail
● Without mounting rail
For corresponding conditions, refer to the next chapters.
2.1 Installation without mounting rail
Simple installation
The ET 200eco PN distributed I/O device is designed for easy installation.
● The I/O device must be mounted on a solid base
● and can be prewired.
Requirements
Screw type Description
Cylinder head screw M5 according to ISO 1207/ISO 1580
(DIN 84/DIN85)
Hexagon socket head cap screw M5 according to DIN EN
ISO 4762
Minimum screw length: 30 mm.
Any washers you might need should conform to DIN 125.
Tools required
Medium-sized screwdriver or 4 mm hex socket driver.

Installing
2.1 Installation without mounting rail
ET 200eco PN
20 Operating Instructions, 06/2009, A5E01250250-04
Procedure
1. Screw the I/O device onto a level surface.
Screw the I/O device onto the panel at both mounting fixtures on the top and bottom of
the front or side (torque: 3 N/m).
 




Figure 2-1 Mounting the I/O device on a panel (30 mm)






Figure 2-2 Mounting the I/O device on a panel (60 mm wide), for example
16 DO DC 24V/1,3A 8×M12