Siemens SL45 User manual

slider SL45
Operating instructions
en

3
SIEMENS
Index Page
General safety instructions 4
1 Description 6
2 Preparations 7
3 Setting the temperature 8
4 Ironing with steam 8
5 “pulseSteam” function 9
6 Ironing without steam 9
7 Vertical steam 9
8 “Intelligent steam” function 10
9 Energy saving button 10
10 Auto shut-off 10
11 Fabric protection soleplate cover 10
12 calc’nClean Plus 10
13 Rinsing the iron steam chamber 12
14 Cleaning & Maintenance 13
15 Storing the appliance 13
16 Tips to help you save energy 14
17 Advice on disposal 14
18 Guarantee conditions 14
19 Trouble shooting 15

4SIEMENS
Thank you for buying the slider
SL45 steam station, the new steam-
ironing system from Siemens.
Carefully read through the operating
instructions for the appliance and
safeguard them for future reference.
Introduction
These instructions for use contain
valuable information about the unique
features of this system and some hints
to make ironing easier for you. We
hope that you enjoy ironing with this
steam station.
Important
Open out the rst page of the booklet,
this will help you to understand how
the appliance works. This appliance
complies with international safety
standards.
This appliance has been designed
exclusively for domestic use and must
not be used for industrial purposes.
This appliance must be used only for
the purposes for which it was designed,
i.e. as an iron. Any other use will be
considered improper and consequently
dangerous. The manufacturer will not
be held responsible for any damage
arising from misuse or improper use.
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Keep the iron and its cord out of reach of children less
than 8 years of age when it is energized or cooling down.
• CAUTION. Hot surface.
Sur fa ce is liable to get hot during use.
General safety instructions
• The iron must not be left unattended while it is connected
to the supply mains.
• Remove the plug from the socket before lling the
appliance with water or before pouring out the remaining
water after use.
• The appliance must be used and placed on a stable
surface.
• When placed on its stand, make sure that the surface on
which the stand is placed is stable.
• The iron should not be used if it has been dropped, if
there are visible signs of damage or if it is leaking water.
It must be checked by an authorized Technical Service
Centre before it can be used again.
• With the aim of avoiding dangerous situations, any work
or repair that the appliance may need, e.g. replacing a
faulty mains cable, must only be carried out by qualied
personnel from an Authorised Technical Service Centre.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
• This appliance is to be connected
and used in accordance with
the information stated on its
characteristics plate.
• This appliance must be connected to
an earthed socket. If it is absolutely
necessary to use an extension cable,
make sure that it is suitable for 16A
and has a socket with an earth
connection.
• If the safety fuse tted in the
appliance blows, the appliance will
be rendered inoperative. To restore
normal operation the appliance will
have to be taken to an authorised
Technical Service Centre.
• In order to avoid that, under
unfavourable mains conditions,
phenomena like transient voltage
drops or lighting uctuations can
happen, it is recommended that the
iron is connected to a power supply
system with a maximum impedance
of 0.27Ω . If necessary, the user
can ask the public power supply
company for the system impedance
at the interface point.
• The appliance must never be placed
directly under the tap to ll the water
tank.

5
SIEMENS
Important
Open out the rst page of the booklet,
this will help you to understand how
the appliance works. This appliance
complies with international safety
standards.
This appliance has been designed
exclusively for domestic use and must
not be used for industrial purposes.
This appliance must be used only for
the purposes for which it was designed,
i.e. as an iron. Any other use will be
considered improper and consequently
dangerous. The manufacturer will not
be held responsible for any damage
arising from misuse or improper use.
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Keep the iron and its cord out of reach of children less
than 8 years of age when it is energized or cooling down.
• CAUTION. Hot surface.
Sur fa ce is liable to get hot during use.
General safety instructions
• The iron must not be left unattended while it is connected
to the supply mains.
• Remove the plug from the socket before lling the
appliance with water or before pouring out the remaining
water after use.
• The appliance must be used and placed on a stable
surface.
• When placed on its stand, make sure that the surface on
which the stand is placed is stable.
• The iron should not be used if it has been dropped, if
there are visible signs of damage or if it is leaking water.
It must be checked by an authorized Technical Service
Centre before it can be used again.
• With the aim of avoiding dangerous situations, any work
or repair that the appliance may need, e.g. replacing a
faulty mains cable, must only be carried out by qualied
personnel from an Authorised Technical Service Centre.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
• This appliance is to be connected
and used in accordance with
the information stated on its
characteristics plate.
• This appliance must be connected to
an earthed socket. If it is absolutely
necessary to use an extension cable,
make sure that it is suitable for 16A
and has a socket with an earth
connection.
• If the safety fuse tted in the
appliance blows, the appliance will
be rendered inoperative. To restore
normal operation the appliance will
have to be taken to an authorised
Technical Service Centre.
• In order to avoid that, under
unfavourable mains conditions,
phenomena like transient voltage
drops or lighting uctuations can
happen, it is recommended that the
iron is connected to a power supply
system with a maximum impedance
of 0.27Ω . If necessary, the user
can ask the public power supply
company for the system impedance
at the interface point.
• The appliance must never be placed
directly under the tap to ll the water
tank.
• Unplug the appliance from the mains
supply after each use, or if a fault is
suspected.
• The electrical plug must not be
removed from the socket by pulling
the cable.
• Never immerse the iron in water or
any other uid.
• Do not leave the appliance exposed
to weather conditions (rain, sun,
frost, etc.)
Important:
▪ This appliance reaches high
temperatures and produces steam
during use, this could cause scalds or
burns if not used properly.
▪ The steam hose, base station, metal
plate at the bottom of the removable
iron pad (2) and in particular the
iron can get hot when used. This is
normal.
▪ Never aim the steam at people or
animals.
▪ Do not allow the power cable to come
into contact with the soleplate when
it is hot.
▪ Be aware that the system can keep
on steaming for a short additional
time after releasing the steam trigger.
This is a normal function.

6SIEMENS
* Model dependent
* Model dependent
1
Description
2
Preparations
1. Release the iron from its lock system
(13) by pulling the lever located at
the heel of the iron backwards.
2. Remove any label or protective
covering from the soleplate.
3. Place the appliance horizontally on a
solid, stable surface. You may remove
the iron pad from the appliance and
place the iron on it on another solid,
stable, horizontal surface.
4. Fill the water tank.
5. Unwind the mains cable (6) fully and
plug it into an earthed socket.
6. Set the main power button (12) to the
on position (illuminated in red).
7. The “Steam ready” indicator lamp (9)
will light up after several minutes,
indicating that the appliance is ready
to use.
1. Water tank
2. Removable iron pad
3. Carrying handles
4. “calc’nClean Plus” scale collector
5. Steam hose and mains cable
storage compartment
6. Mains cable
7. Steam hose
8. “Energy Saving” button *
9. “Steam ready” / “Auto shut-off” pilot
light
10. Variable steam control *
11. “Rell water tank” / “Clean warning”
pilot light
12. Illuminated main power button (0/I)
13. Iron xation system “secureLock”
14. Housing with internal steam
generator
15. Temperature control knob
16. Steam release button
17. Steam release button “XTRM” *
18. Iron pilot light
19. Soleplate
20. Fabric-protection soleplate cover *
* Model dependent
12 11 10* 8*9
20*
17*
18
19 16
15
3
2
56
13
14
4
1
7
12 11 10*
8*
9

* Model dependent
7
SIEMENS
* Model dependent
1
Description
2
Preparations
1. Release the iron from its lock system
(13) by pulling the lever located at
the heel of the iron backwards.
2. Remove any label or protective
covering from the soleplate.
3. Place the appliance horizontally on a
solid, stable surface. You may remove
the iron pad from the appliance and
place the iron on it on another solid,
stable, horizontal surface.
4. Fill the water tank.
5. Unwind the mains cable (6) fully and
plug it into an earthed socket.
6. Set the main power button (12) to the
on position (illuminated in red).
7. The “Steam ready” indicator lamp (9)
will light up after several minutes,
indicating that the appliance is ready
to use.
The steam generator will take more
time to reach “Steam ready” state
only upon the initial heating up, or
after performing the de-scaling
operation (calc’nClean).
When water is already present in the
steam generator during regular use,
heat up time to reach the operating
temperature will be faster.
8. This appliance has a built-in water
level sensor. The “rell water tank”
indicator (11) will light when the
water tank is empty.
Important:
• Normal tap water can be used.
To prolong the optimum steam
function, mix tap water with distilled
water 1:1. If the tap water in your
district is very hard, mix tap water
with distilled water 1:2.
You can inquire about the water
hardness with your local water
supplier.
• The water tank can be lled at any
time while using the appliance.
• To avoid damage and/or
contamination of the water tank and
the boiler, do not put perfume,
vinegar, starch, descaling agents,
additives or any other type of
chemical product into the water tank.
Any damage caused by the use of
the aforementioned products, will
make the guarantee void.
• Do not use condensation water
from tumble dryers, air conditioning
systems or similar. This appliance
has been designed to use normal tap
water.
11. “Rell water tank” / “Clean warning”
pilot light
12. Illuminated main power button (0/I)
13. Iron xation system “secureLock”
14. Housing with internal steam
generator
15. Temperature control knob
16. Steam release button
17. Steam release button “XTRM” *
18. Iron pilot light
19. Soleplate
20. Fabric-protection soleplate cover *
* Model dependent

8SIEMENS
* Model dependent
* Model dependent
• The iron is not designed to rest on its
heal. Please always position it
horizontally on the iron pad (2).
• The iron pad can be placed into the
specially designed recess on the
appliance or somewhere suitable
alongside the ironing area.
Never rest the iron on the
appliance without the iron pad!.
• During it rst use the iron may
produce certain vapours and odours,
along with white particles on the
soleplate, this is normal and it will
stop after a few minutes
• While the steam release button is
pressed, the water tank may produce
a pumping sound, this is normal,
indicating that water is being pumped
to the steam tank.
3
Setting the
temperature
1. Check the ironing instruction label on
the garment to determine the correct
ironing temperature.
2. Turn the temperature selector (15) to
the required setting:
• Synthetics
•• Silk – Wool
••• Cotton – Linen
3. The indicator lamp (18) will remain lit
while the iron is heating and go out
as soon as the iron has reached the
selected temperature.
Tips:
• Sort your garments out based on
their cleaning symbol labels, always
starting with clothes that have to be
ironed at the lowest temperatures.
• If you are not sure what the garment
is made of then begin ironing at a
low temperature and decide on the
correct temperature by ironing a
small section not usually seen when
worn.
4
Ironing with
steam
The steam control is used to adjust
the amount of steam produced when
ironing.
1. Turn the temperature selector (15) to
the required setting.
2. Model dependent:
Set the amount of steam to suit your
needs, using the variable steam
control (10*).
For normal use, please choose one
of the following recommended
settings:
Temperature Steam setting
•
••
•••
3. Press the steam (16-17*) release
button to release steam.
1617*
Attention:
When ironing on a lower temperature
setting “•”.
• If the appliance has variable steam
control (10*), set the variable steam
control to its lowest position .
• If the appliance does not have
variable steam control, press the
steam release button only for a few
seconds at a time when ironing at
lower temperatures.
In both cases, if you nd that water
is dripping out of the soleplate, set
the temperature selector (15) to a
higher position (take care that the
garment can be ironed on this heat
temperature setting).
• At the beginning of each use, it is
possible that drops of water will be
dispensed alongside steam.
Therefore, it is advisable to try the
iron on the ironing board or a piece
of cloth to start with.
Tip : for better ironing results, iron the
last strokes without steam to dry the
garment.
5
“pulseSteam”
function
This appliance has a special function
for tackling difcult creases.
The “pulseSteam” function helps soften
stubborn garments like jeans or linen
faster.
When the steam release button is
activated, the steam generator will give
three powerful shots of steam so that
the steam reaches even deeper into
the fabrics.
1. Set the temperature selector (15) on
“•••”.
2. Press the steam release button (16)
on the bottom of the handle two
times in quick succession (double-
click).
or (model dependent).
Briey press the steam release
button (17*) on the top of the handle.

* Model dependent
9
SIEMENS
* Model dependent
4
Ironing with
steam
The steam control is used to adjust
the amount of steam produced when
ironing.
1. Turn the temperature selector (15) to
the required setting.
2. Model dependent:
Set the amount of steam to suit your
needs, using the variable steam
control (10*).
For normal use, please choose one
of the following recommended
settings:
Temperature Steam setting
•
••
•••
3. Press the steam (16-17*) release
button to release steam.
1617*
Attention:
When ironing on a lower temperature
setting “•”.
• If the appliance has variable steam
control (10*), set the variable steam
control to its lowest position .
• If the appliance does not have
variable steam control, press the
steam release button only for a few
seconds at a time when ironing at
lower temperatures.
In both cases, if you nd that water
is dripping out of the soleplate, set
the temperature selector (15) to a
higher position (take care that the
garment can be ironed on this heat
temperature setting).
• At the beginning of each use, it is
possible that drops of water will be
dispensed alongside steam.
Therefore, it is advisable to try the
iron on the ironing board or a piece
of cloth to start with.
Tip : for better ironing results, iron the
last strokes without steam to dry the
garment.
5
“pulseSteam”
function
This appliance has a special function
for tackling difcult creases.
The “pulseSteam” function helps soften
stubborn garments like jeans or linen
faster.
When the steam release button is
activated, the steam generator will give
three powerful shots of steam so that
the steam reaches even deeper into
the fabrics.
1. Set the temperature selector (15) on
“•••”.
2. Press the steam release button (16)
on the bottom of the handle two
times in quick succession (double-
click).
or (model dependent).
Briey press the steam release
button (17*) on the top of the handle.
Remarks:
• It is possible to stop the shots of
steam by quickly pressing the steam
button again.
• Some water drops may appear when
you use the “pulseSteam” function
for the rst time.
The water drops will disappear after
you have used the function for some
time.
6
Ironing without
steam
Begin ironing but without pressing the
steam release button.
7
Vertical steam
This can be used to remove creases
from hanging clothes, curtains etc.
Warning!:
• Never direct the steam jet at
garments that are being worn.
• Never aim the steam at people or
animals.
1.Set the temperature control knob to
at least the “•••” position.
2. Hold the iron in an upright position
15 cm away from the garment being
steamed.
3. You can steam iron curtains and
hanging garments (jackets, suits,
coats...) by placing the iron in a
vertical position and pressing the
steam release button (16 or 17*).
15 cm

10 SIEMENS
* Model dependent
* Model dependent
8
“Intelligent steam”
function
(model dependent)
This system has intelligent steam
control, which, after releasing the
steam release button (16), provides a
small amount of additional steam.
The additional steam can always be
stopped by briey pressing the steam
release button once again.
9
Energy saving
button
(model dependent)
If the “Energy saving” button (8*) is
switched on, you can save up to 25%
of the energy and 40% of the water
consumption (*), and still achieve
good results when ironing most of your
garments.
It is advisable to use the normal energy
setting only for thick and very wrinkled
fabrics.
(*) In comparison to the maximum
setting.
Note: If you work with the “Energy
saving” function, the variable steam
regulation and temperature regulation
can still be used as recommended.
10
Auto shut-off
(model dependent)
If during ironing, the steam release
button (16-17*) on the iron handle
is not pressed for a certain length of
time (8 minutes), the steam station will
automatically switch off.
The “auto shut-off” pilot lamp (9) will
ash when auto shut-off has been
activated.
To switch the steam station back on,
press the steam release button again.
11
Fabric protection
soleplate cover
(model dependent)
The fabric-protection soleplate cover
(20*) is used for steam-ironing delicate
garments at maximum temperature
without damaging them. Use of the
soleplate cover also does away with
the need for a cloth to prevent shine on
dark materials.
It is advisable to rst iron a small
section on the inside of the garment to
see if it is suitable.
To attach the soleplate cover to the
iron, place the tip of the iron into the
end of the soleplate cover and pull the
elastic strap over the lower rear of the
iron until it ts tightly. To release the
soleplate cover, pull the elastic strap
and remove the iron.
1
23
The fabric-protection soleplate cover
may be purchased from our customer
service or from our website:
Accessory code
(After-sales)
Name of
accessory
(Online shop)
571510 TZ20450
12
calc’nClean Plus
Cleaning the Boiler
To extend the life of your steam
generator and to prevent any build up
of scale, it is essential that you rinse
out the lter (4) and the boiler after
several hours of use. If the water is
hard, increase the frequency.
Do not use descaling agents for rinsing
out the boiler, as they could damage it.
Automatic clean warning
Pilot light (11) will ash indicating that
boiler must be rinsed.
5
x2
8
9
1
~2 h.
ºC
A2
2
3-4
70,25 L.
6
a b
250 ml
25 ml

* Model dependent
11
SIEMENS
* Model dependent
11
Fabric protection
soleplate cover
(model dependent)
The fabric-protection soleplate cover
(20*) is used for steam-ironing delicate
garments at maximum temperature
without damaging them. Use of the
soleplate cover also does away with
the need for a cloth to prevent shine on
dark materials.
It is advisable to rst iron a small
section on the inside of the garment to
see if it is suitable.
To attach the soleplate cover to the
iron, place the tip of the iron into the
end of the soleplate cover and pull the
elastic strap over the lower rear of the
iron until it ts tightly. To release the
soleplate cover, pull the elastic strap
and remove the iron.
1
23
The fabric-protection soleplate cover
may be purchased from our customer
service or from our website:
Accessory code
(After-sales)
Name of
accessory
(Online shop)
571510 TZ20450
12
calc’nClean Plus
Cleaning the Boiler
To extend the life of your steam
generator and to prevent any build up
of scale, it is essential that you rinse
out the lter (4) and the boiler after
several hours of use. If the water is
hard, increase the frequency.
Do not use descaling agents for rinsing
out the boiler, as they could damage it.
Automatic clean warning
Pilot light (11) will ash indicating that
boiler must be rinsed.
5
x2
8
9
1
~2 h.
ºC
A2
2
3-4
70,25 L.
6
a b
250 ml
25 ml
1. Check carefully that the appliance is
cold and unplugged for more than 2
hours, and that the water tank (1) is
empty.
2. Fix the iron to the stand by inserting
the tip of the iron into the front slot
and moving the xation lever (13)
against the heel of the iron.
3. Place your appliance over a sink or
bucket.
4. Lean the appliance on the opposite
side of the lter opening.
5. Unscrew the lter (4) and take it out.
6. (model dependent)
To wash the lter, you may:
a. Place the lter under the water tap
and wash it up until calc residues
are removed. Squeeze the lter as
indicated in the picture 6a.
b. Immerse the lter in tap water (250
ml) mixed with a measure (25 ml)
of descaling uid.
The descaling uid can be obtained
from our After-sales service or from
our website.
Accessory code
(After-sales)
Name of
accessory
(Online shop)
311144 TZ11001
7. Holding your steam generator in the
lateral position and using a jug, ll
the boiler with 1/4 litre of water and
replace the lter.
8. Shake the base unit for a few
moments, unscrew the lter again
and empty the boiler completely over
a sink or bucket.
For best results, we recommend that
this operation is performed twice.
Important: before re-closing, make
sure no water remains in the boiler.
9. Replace and tighten up the lter.
To reset the “calc’nClean” counter,
switch the steam station off twice,
keeping it off for at least 30 seconds
each time.
(on → 30s off → on → 30s off → on)

12 SIEMENS
* Model dependent
* Model dependent
13
Rinsing the iron
steam chamber
Caution! Risk of burns!
This procedure helps to remove scale
particles out of the steam chamber.
This cleaning procedure may be
performed occasionally (approximately
once a year), when after a long period
of use with very hard water, scale
particles start to come out of the
soleplate.
a) Ensure that the iron is cooled down.
b) Set the temperature selector (15) of
the iron to the “min” position.
c) Fill the tank with tap water.
d) Plug in the mains cable and set the
main power switch (12) to the “I”
position (illuminated in red)
e) Wait until the “steam ready” indicator
lamp (9) lights up.
f) If the steam station has steam
regulator (10*), set it to the maximum
position.
g) Hold the iron over the sink or a
container to collect the water.
h) Press the steam release button
(16) and gently shake the iron.
Boiling water and steam will come
out, carrying scale and or deposits
that might be there. This could take
approximately 5 minutes.
i) Set the temperature selector (15) of
the iron to the “max” position, without
pressing the steam release button
(16). The water in the steam chamber
will start evaporating. Wait until all the
water inside the chamber has been
evaporated.
j) To clean the soleplate, immediately
rub off any residue by running the hot
iron over dry cotton cloth.
d
a
b
c
e
f
g
h
5’
i
j
14
Cleaning &
Maintenance
Attention! Risk of burns!
Always unplug the appliance from
the mains supply before carrying
out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and
allow the appliance to cool down
before cleaning.
2. Wipe the housing, handle and iron
body with a damp cotton cloth.
3. If the soleplate is soiled with dirt or
scale, clean it with a damp cotton
cloth.
4. If the cloth is synthetic, it may melt
due to the high temperature on the
soleplate (19). Switch off the steam
and rub off any residue immediately
with a thickly folded, dry cotton cloth.
5. Never use abrasive products or
solvents. To keep the soleplate (19)
smooth, you should avoid hard
contact with metal objects. Never
use a scouring pad, or chemicals to
clean the soleplate.

* Model dependent
13
SIEMENS
* Model dependent
d
a
b
c
e
f
g
h
5’
i
j
14
Cleaning &
Maintenance
Attention! Risk of burns!
Always unplug the appliance from
the mains supply before carrying
out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and
allow the appliance to cool down
before cleaning.
2. Wipe the housing, handle and iron
body with a damp cotton cloth.
3. If the soleplate is soiled with dirt or
scale, clean it with a damp cotton
cloth.
4. If the cloth is synthetic, it may melt
due to the high temperature on the
soleplate (19). Switch off the steam
and rub off any residue immediately
with a thickly folded, dry cotton cloth.
5. Never use abrasive products or
solvents. To keep the soleplate (19)
smooth, you should avoid hard
contact with metal objects. Never
use a scouring pad, or chemicals to
clean the soleplate.
15
Storing the
appliance
1. Always allow the appliance to cool
down before storing it.
2. Set the main power button to the “0”
position (the red light will go off) and
disconnect the mains cable.
3. Empty the water tank.
4. Place the iron on the iron pad (2),
standing on the soleplate, and x it
by inserting the tip of the iron into the
front slot and moving the lock lever
(13) against the heel of the iron.
A
2
5. Store the mains cable (6) and steam
hose (7) in the storage compartment
(5). Do not wrap the cords too tight.
6. Hold the iron´s handle when moving
the appliance, as shown in gure
below, or use the carrying handles
(3) on the sides.

14 SIEMENS
* Model dependent
* Model dependent
16
Tips to help you
save energy
Steam production consumes the most
energy. To help minimise the energy
used, follow the advice below:
• Start by ironing the fabrics
that require the lowest ironing
temperature.
Check the recommended ironing
temperature in the label on the
garment.
• Regulate the steam according to
the selected ironing temperature,
following the instructions in this
manual.
• Try to Iron the fabrics while they are
still damp and reduce the steam
setting. Steam will be generated from
the fabrics rather than the iron. If you
tumble dry your fabrics before ironing
them, set the tumble drier on the
‘iron dry’ programme.
• If the fabrics are damp enough, turn
off the steam regulator completely.
17
Advice on disposal
Our goods come in optimised
packaging. This basically consists in
using non-contaminating materials
which should be handed over to
the local waste disposal service as
secondary raw materials. Your local
town council can give you information
about how to dispose of obsolete
appliances.
This appliance is labelled in
accordance with European
Directive 2012/19/EU
concerning used electrical
and electronic appliances
(waste electrical and
electronic equipment - WEEE).
The guideline determines the
framework for the return and
recycling of used appliances as
applicable throughout the EU.
18
Guarantee conditions
The terms of the guarantee for this
appliance are in accordance with that
stated by our representative for the
country in which it is sold.
The details of these conditions can be
obtained from the retailer from whom
the appliance was purchased. The
purchase receipt must be presented
when making any claims against the
terms of this guarantee.
19
Trouble shooting
Problem Possible causes Solution
Pilot light (11)
ashes
• Boiler and lter must be
rinsed.
• Rinse the lter and the
boiler according to the
cleaning instructions in
this manual (see section
“calc’nClean Plus”).
The steam
generator does
not come on.
• There is a connection
problem.
• The main power button is
not switched on.
• Check the mains cable (6),
the plug and the socket.
• Set the main power button
(12) to the “I” position
(illuminated in red).
The iron does not
heat up.
• The main power button is
not switched on.
• The temperature is set to a
low position.
• Set the main power button
(12) to the “I” position
(illuminated in red).
• Set the temperature to the
desired position.
The iron begins
to smoke when
switched on.
• During rst use: certain
components on the
appliance have been lightly
greased at the factory and
may produce a little smoke
when initially heated.
• During subsequent use: the
soleplate may be soiled.
• This is completely normal
and will stop after a short
while.
• Clean the soleplate
according to the cleaning
instructions in this manual.
Water ows
through the holes
on the soleplate.
• The steam function is being
used before it has reached
the correct temperature.
• The water is condensing
inside the pipes because
steam is being used for the
rst time or has not been
used for a long time.
• The steam generator
contains too much scale.
• Reduce the steam ow
when ironing at low
temperatures.
• Point the iron away from the
ironing area and press the
steam release button until
steam is produced.
• Clean the boiler as
described in section
“calc'nClean Plus”.

* Model dependent
15
SIEMENS
* Model dependent
18
Guarantee conditions
The terms of the guarantee for this
appliance are in accordance with that
stated by our representative for the
country in which it is sold.
The details of these conditions can be
obtained from the retailer from whom
the appliance was purchased. The
purchase receipt must be presented
when making any claims against the
terms of this guarantee.
19
Trouble shooting
Problem Possible causes Solution
Pilot light (11)
ashes
• Boiler and lter must be
rinsed.
• Rinse the lter and the
boiler according to the
cleaning instructions in
this manual (see section
“calc’nClean Plus”).
The steam
generator does
not come on.
• There is a connection
problem.
• The main power button is
not switched on.
• Check the mains cable (6),
the plug and the socket.
• Set the main power button
(12) to the “I” position
(illuminated in red).
The iron does not
heat up.
• The main power button is
not switched on.
• The temperature is set to a
low position.
• Set the main power button
(12) to the “I” position
(illuminated in red).
• Set the temperature to the
desired position.
The iron begins
to smoke when
switched on.
• During rst use: certain
components on the
appliance have been lightly
greased at the factory and
may produce a little smoke
when initially heated.
• During subsequent use: the
soleplate may be soiled.
• This is completely normal
and will stop after a short
while.
• Clean the soleplate
according to the cleaning
instructions in this manual.
Water ows
through the holes
on the soleplate.
• The steam function is being
used before it has reached
the correct temperature.
• The water is condensing
inside the pipes because
steam is being used for the
rst time or has not been
used for a long time.
• The steam generator
contains too much scale.
• Reduce the steam ow
when ironing at low
temperatures.
• Point the iron away from the
ironing area and press the
steam release button until
steam is produced.
• Clean the boiler as
described in section
“calc'nClean Plus”.

16 SIEMENS
* Model dependent
* Model dependent
Problem Possible causes Solution
Dirt comes out
through the
soleplate.
• There is a build up of scale
or minerals in the steam
tank.
• Chemical products or
additives have been used.
• Use tap water mixed
50% with distilled or
demineralised water. To
prolong the optimum steam
function, mix tap water with
distilled water 1:1. If the tap
water in your district is very
hard, mix tap water with
distilled water 1:2.
• Clean the soleplate with a
damp cloth.
• Never add products to the
water.
The iron does
not produce any
steam.
• The boiler is not switched
on or the water tank is
empty.
• The steam regulation is set
to the minimum position.
• Set the main power button
(12) to the “I” position
(illuminated in red), and/or
ll the water tank.
• Increase the steam ow
(see section “Ironing with
steam”).
The ironed
garment turns
dark and/or sticks
to the soleplate.
• The selected temperature is
too high and has damaged
the garment.
• Select a suitable
temperature for the material
being ironed and clean the
soleplate with a damp cloth.
The soleplate
turns brown.
• This is a regular
consequence of continued
use over a long period of
time.
• Clean the soleplate with a
damp cloth.
The appliance
makes a pumping
sound.
• Water is being pumped into
the steam tank.
• Water tank (1) is not
correctly inserted in the
housing.
• The sound will not stop.
• This is normal.
• Adjust the water tank to t
correctly.
• If the sound will not stop, do
not use the steam generator
and contact an authorised
technical service centre.
Loss of pressure
during ironing.
• Steam release button has
been activated for too long
a period of time, that is,
it has been pressed too
frequently.
• Use the steam release
button at intervals. This
improves the ironing result
as the textiles will be
steamed, dried and ironed
properly.
Problem Possible causes Solution
Water spots
appear on the
garment during
ironing.
• May be caused by steam
condensed on the ironing
board.
• Wipe the textile cover of the
ironing board, and iron any
water drops to dry them.
Water spots
appear on the
garment during
use of the
“pulseSteam”
function.
• Water spots are caused by
steam condensation in the
hose when cooling down
after use.
• Water drops stop coming
out of the soleplate after
using the “pulseSteam”
function for some time.
The hose gets hot
during use.
• This is normal. It is caused
by the steam passing
through the hose during
steam ironing.
• Place the hose on the
opposite side so that you
cannot touch the hose
during ironing.
Water leakage
from the boiler.
• Filter (4) located at the side
of the appliance is loose.
• Tighten up the lter.
The iron does not
stop steaming
after placing it on
the pad (2).
• “pulseSteam” function has
been activated by double
click.
• Just press the trigger once
again and the iron will stop
steaming at once.
If the above does not solve the problem, get in touch with an authorised technical
service.
You can download this manual from the local homepages of Siemens.

* Model dependent
17
SIEMENS
* Model dependent
Problem Possible causes Solution
Dirt comes out
through the
soleplate.
• There is a build up of scale
or minerals in the steam
tank.
• Chemical products or
additives have been used.
• Use tap water mixed
50% with distilled or
demineralised water. To
prolong the optimum steam
function, mix tap water with
distilled water 1:1. If the tap
water in your district is very
hard, mix tap water with
distilled water 1:2.
• Clean the soleplate with a
damp cloth.
• Never add products to the
water.
The iron does
not produce any
steam.
• The boiler is not switched
on or the water tank is
empty.
• The steam regulation is set
to the minimum position.
• Set the main power button
(12) to the “I” position
(illuminated in red), and/or
ll the water tank.
• Increase the steam ow
(see section “Ironing with
steam”).
The ironed
garment turns
dark and/or sticks
to the soleplate.
• The selected temperature is
too high and has damaged
the garment.
• Select a suitable
temperature for the material
being ironed and clean the
soleplate with a damp cloth.
The soleplate
turns brown.
• This is a regular
consequence of continued
use over a long period of
time.
• Clean the soleplate with a
damp cloth.
The appliance
makes a pumping
sound.
• Water is being pumped into
the steam tank.
• Water tank (1) is not
correctly inserted in the
housing.
• The sound will not stop.
• This is normal.
• Adjust the water tank to t
correctly.
• If the sound will not stop, do
not use the steam generator
and contact an authorised
technical service centre.
Loss of pressure
during ironing.
• Steam release button has
been activated for too long
a period of time, that is,
it has been pressed too
frequently.
• Use the steam release
button at intervals. This
improves the ironing result
as the textiles will be
steamed, dried and ironed
properly.
Problem Possible causes Solution
Water spots
appear on the
garment during
ironing.
• May be caused by steam
condensed on the ironing
board.
• Wipe the textile cover of the
ironing board, and iron any
water drops to dry them.
Water spots
appear on the
garment during
use of the
“pulseSteam”
function.
• Water spots are caused by
steam condensation in the
hose when cooling down
after use.
• Water drops stop coming
out of the soleplate after
using the “pulseSteam”
function for some time.
The hose gets hot
during use.
• This is normal. It is caused
by the steam passing
through the hose during
steam ironing.
• Place the hose on the
opposite side so that you
cannot touch the hose
during ironing.
Water leakage
from the boiler.
• Filter (4) located at the side
of the appliance is loose.
• Tighten up the lter.
The iron does not
stop steaming
after placing it on
the pad (2).
• “pulseSteam” function has
been activated by double
click.
• Just press the trigger once
again and the iron will stop
steaming at once.
If the above does not solve the problem, get in touch with an authorised technical
service.
You can download this manual from the local homepages of Siemens.

001 SL45-reg GB../03/13
Customer Service
Great Britain
Siemens Customer Service
Grand Union House
Old Wolverton Road
Milton Keynes
MK12 5PT
UK: [phone]
IRL: [phone]
www.siemensappliances.co.uk