Siemens SIMATIC NET Series User manual

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C487-02
Ⓟ
10/2018 Subject to change
Copyright © Siemens AG 2018.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 3
Table of contents
1 SCALANCE W1788-x ............................................................................................................................. 7
1.1 Type designations.....................................................................................................................8
1.2 EC declaration of conformity.....................................................................................................9
1.2.1 ATEX.......................................................................................................................................10
1.2.2 RoHS.......................................................................................................................................11
1.2.3 RED.........................................................................................................................................11
1.2.3.1 Protection of health and safety ...............................................................................................11
1.2.3.2 EMC ........................................................................................................................................12
1.2.3.3 Efficient use of the radio spectrum .........................................................................................13
1.2.4 Products..................................................................................................................................13
1.3 General approvals...................................................................................................................14
1.4 National approvals ..................................................................................................................19

Table of contents
Approvals SCALANCE W1700 802.11ac
4Reference Manual, 11/2018, C79000-G8976-C487-02

Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 5
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers’ exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under https://www.siemens.com/industrialsecurity.

SCALANCE W1788-x
Approvals SCALANCE W1700 802.11ac
6Reference Manual, 11/2018, C79000-G8976-C487-02

Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 7
SCALANCE W1788-x
1
Note
Issued approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.
You can check which of the following approvals have been
granted for your product by the
markings on the type plate.

SCALANCE W1788-x
1.1 Type designations
Approvals SCALANCE W1700 802.11ac
8Reference Manual, 11/2018, C79000-G8976-C487-02
1.1
Type designations
Scope of validity
The approvals listed in this section apply to the following products:
Product
Article number
Access point
SCALANCE W1788-1 M12 6GK5788-1GY01-0AA0
Dual access points
SCALANCE W1788-2 M12
6GK5788-2GY01-0AA0
SCALANCE W1788-2 M12 EEC
6GK5788-2GY01-0TA0
SCALANCE W1788-2IA M12
6GK5788-2HY01-0AA0
Abbreviations used
Some approvals apply only to certain devices or series. In such situations, the designations
of the products are shortened to avoid having to list all the type designations. The following
table shows how the abbreviations relate to the product variants.
Designation
Product
SCALANCE W1788-x SCALANCE W1788-1 M12
SCALANCE W1788-2 M12
SCALANCE W1788-2 M12 EEC
SCALANCE W1788-2IA M12

SCALANCE W1788-x
1.2 EC declaration of conformity
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 9
1.2
EC declaration of conformity
The EC Declaration of Conformity is available for all responsible authorities at:
Siemens Aktiengesellschaft
Process Industries and Drives Division,
Process Automation
DE-76181 Karlsruhe
Germany
You can find the current EU declaration of conformity for these products on the Internet
pages under Siemens Industry Online Support
(https://support.industry.siemens.com/cs/ww/en/ps/15853/cert).
The SIMATIC NET products described in this document meet the requirements of the
following EU directives:
●ATEX directive 2014/34/EU
Directive of the European Parliament and the Council of 26 February 2014 on the
approximation of the laws of the member states concerning equipment and protective
systems intended for use in potentially explosive atmospheres, official journal of the EU
L96, 29/03/2014, pages 309–356
●RoHS directive 2011/65/EU
Directive of the European Parliament and of the Council of 8 June 2011 on the restriction
of the use of certain hazardous substances in electrical and electronic equipment, official
journal of the EC L174, 01/07/2011, pages 88-110
●Radio equipment directive 2014/53/EU (RED, Radio Equipment Directive)
Directive of the European Parliament and of the Council of 16 April 2014 on the
harmonization of the laws of the member states relating to placing radio equipment on the
market; official journal of the EU L153, 22/05/2014, pages 62–106

SCALANCE W1788-x
1.2 EC declaration of conformity
Approvals SCALANCE W1700 802.11ac
10 Reference Manual, 11/2018, C79000-G8976-C487-02
1.2.1
ATEX
ATEX directive (correct usage in potentially explosive atmospheres)
The SIMATIC NET product meets the requirements of the EU directive 2014/34/EU
"Equipment and Protective Devices for Use in Potentially Explosive Atmospheres" according
to the standards listed in the section "Products (Page 13)" to one of the following types of
protection:
Type of protection
Applied standards
nA
ec
1 ✓✓EN 60079-0 + A11
Hazardous areas - Part 0: Equipment - General requirements
2 ✓- EN 60079-15
Explosive atmospheres - Part 15: Equipment protection by type of
protection "n"
3 - ✓EN 60079-7
Explosive atmospheres - Part 7: Equipment protection through
increased safety "e"

SCALANCE W1788-x
1.2 EC declaration of conformity
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 11
1.2.2
RoHS
RoHS directive (restriction of the use of certain hazardous substances)
The SIMATIC NET products described in these operating instructions meet the requirements
of the EC directive 2011/65/EC for the restriction of the use of certain hazardous substances
in electrical and electronic equipment:
Applied standard:
4
EN 50581
Technical documentation for the assessment electrical and electronic products with
respect to restriction of hazardous substances
1.2.3
RED
1.2.3.1
Protection of health and safety
Article 3 (1) a) protection of health and safety
5
EN
62368-1
Equipment for audio, video, information and comm
unication technology - Part 1:
Safety requirements
6
EN 62311
Assessment of electronic and electrical equipment related to human exposure r
e-
strictions for electromagnetic fields (0 Hz – 300 GHz)

SCALANCE W1788-x
1.2 EC declaration of conformity
Approvals SCALANCE W1700 802.11ac
12 Reference Manual, 11/2018, C79000-G8976-C487-02
1.2.3.2
EMC
Art. 3 (1) b - EMC
7
EN
50121-3-2+AC
Railway applications
- Electromagnetic compatibility - part 3-2: Railway Vehicles -
Devices
8
EN
50121-4+AC
Railway applications
- Electromagnetic compatibility - part 4: Interfere
nce emissions
and immunity of signal telecommunications equipment
9
ETSI
EN 301 489-1
Electromagnetic compatibility and radio spectrum matters (ERM)
- Electromagnetic
compatibility for radio equipment and services
- Part 1 : Common technical re-
quirements
10
ETSI EN 301 489
-3
Electromagnetic compatibility and radio spectrum matters (ERM)
–
Electromagnetic
compatibility (EMC) for radio equipment and services
– Part 3: Specific conditions
for wireless devices with a low range (SRD) for use on frequencies b
etween 9 kHz
and 246 GHz
11
ETSI
EN 301 489-17
Electromagnetic compatibility and radio spectrum matters (ERM)
- Electromagnetic
compatibility for radio equipment and services
- Part 17:
Specific conditions for
broadband data transmission systems
12
EN 55011
Industrial, scientific and medical (ISM) radio
-frequency equipment – Electromagnet-
ic disturbance characteristics – Limits and methods of measurement
13
EN 55032+AC Class A, Class B
Electromagnetic compatibility of multimedia equipment – Emission requirements
14
EN 55035
Electromagnetic compatibility of multimedia equipment - Immunity requirements
15
EN 61000
-6-1
Electromagnetic compatibility (EMC)
- Part 6-1: Generic standards - Immunity for
residential, commercial and light-industrial environments
16
EN 61000
-6-2+AC
Electromagnetic compatibility (EMC)
- Part 6-2: Generic standards - Immunity for
industrial environments
17
EN 61000
-6-3+A1+AC
Electromagnetic compatibility (EMC)
- Part 6-3: Generic standards - Emission
standard for residential, commercial and light-industrial environments
18
EN
61000-6-4+A1
Electromagnetic compatibility (EMC)
- Part 6-4: Generic standards - Emission
standard for industrial environments

SCALANCE W1788-x
1.2 EC declaration of conformity
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 13
1.2.3.3
Efficient use of the radio spectrum
Art. 3 (2) Efficient use of the radio spectrum
19
ETSI
EN 300 328
Broadband transmission systems
– Data transmission equipment operating in the
2.4 GHz ISM band and using broadband modulation techniques. Harmonized EN
covering the essential requirements of article 3.2 of the EU Directive 2014/53/EU
20
ETSI EN 300 440
-2, ETSI EN 300 440
Electromagnetic compatibility and r
adio spectrum matters (ERM) – short range
devices
(SRD) – Radio equipment to be used in the 1 GHz to 40 GHz frequency
range -
Harmonized EN covering the essential requirements of article
3.2 of the EU
Directive 2014/53/EU
21
ETSI
EN 301 893
Broadband Radio Access Networks (BRAN)
– 5 GHz high performance RLAN –
Harmonized EN covering the essential requirements of article 3.2 of the EU D
i-
rective 2014/53/EU
1.2.4
Products
CE conformity
The standards applying to the product are described in ATEX (Page 10), RoHS (Page 11)
and RED (Page 11).
Product
Standards
SCALANCE W1788-1 M12
4, 5, 6, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21
SCALANCE W1788-2 M12
4, 5, 6, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21
SCALANCE W1788-2 M12 EEC
4, 5, 6, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21
SCALANCE W1788-2IA M12
4, 5, 6, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21
Certification ID
The following table shows the product names and the corresponding certification ID:
Product
Certification ID
Article number
SCALANCE W1788-1 M12 RAPAC-W1-M12-E4 6GK5788-1GY01-0AA0
SCALANCE W1788-2 M12
RAPAC-W2-M12-E4
6GK5788-2GY01-0AA0
SCALANCE W1788-2 M12 EEC RAPAC-W2-M12-E4 6GK5788-2GY01-0TA0
SCALANCE W1788-2IA M12
RAPAC-W2-M12-I4
6GK5788-2HY01-0AA0

SCALANCE W1788-x
1.3 General approvals
Approvals SCALANCE W1700 802.11ac
14 Reference Manual, 11/2018, C79000-G8976-C487-02
1.3
General approvals
ATEX (explosion protection directive)
WARNING
Risk of explosion in hazardous areas
When using SIMATIC NET products in hazardous area zone 2, make absolutely sure that
the associated conditions in the following document are adhered to:
"SIMATIC NET Product Information Use of subassemblies/modules in a Zone 2 Hazardous
Area".
You will find this document
•on the data medium that ships with some devices.
•on the Internet pages under Siemens Industry Online Support
(https://support.industry.siemens.com/cs/ww/en/).
Enter the document identification number C234 as the search term.
The SIMATIC NET products meet the requirements of the EU Directive 2014/34/EU
"Equipment and Protective Devices for Use in Potentially Explosive Atmospheres".
Note
Type of protection of the device
The devices are approved for various types of protection. You can find the type of protection
of your device and the ATEX certificate number on the nameplate.

SCALANCE W1788-x
1.3 General approvals
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 15
Permitted types of protection
The following types of protection are possible:
●nA
ATEX classification: II 3G Ex nA IIC T4 Gc
Certificate no.: KEMA 07ATEX0145 X
The products meet the requirements of the following standards:
–EN 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of
protection "n")
–EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
●ec
ATEX classification: II 3G Ex ec IIC T4 Gc
Certificate no.: DEKRA 18ATEX0026X
The products meet the requirements of the following standards:
–EN 60079-7 (Explosive atmospheres - Part 7: Equipment protection through increased
safety "e")
–EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
You will find the current versions of the standards in the currently valid ATEX certificates.

SCALANCE W1788-x
1.3 General approvals
Approvals SCALANCE W1700 802.11ac
16 Reference Manual, 11/2018, C79000-G8976-C487-02
IECEx
The SIMATIC NET products meet the requirements of explosion protection according to
IECEx.
Note
Type of protection of the device
The devices are approved for various types of protection. You can find the type of protection
of your device and the IECEx certificate number on the nameplate.
Permitted types of protection
The following types of protection are possible:
●nA
IECEx classification: Ex nA IIC T4 Gc
Certificate no.: DEK 14.0025X
The products meet the requirements of the following standards:
–EN 60079-15 (Explosive atmospheres - Part 15: Equipment protection by type of
protection "n")
–EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
●ec
IECEx classification: Ex ec IIC T4 Gc
Certificate no.: DEK 18.0018X
The products meet the requirements of the following standards:
–EN 60079-7 (Explosive atmospheres - Part 7: Equipment protection through increased
safety "e")
–EN 60079-0 (Explosive atmospheres - Part 0: Equipment - General requirements)
You will find the current versions of the standards in the currently valid IECEx certificates.
E1
The device meets the requirements of the ECE R10 directive.
Test number 10 R - 057876

SCALANCE W1788-x
1.3 General approvals
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 17
Railway approval
EEC variants of the device meet the requirements of the standards:
●EN 50155 "Railway applications - Electronic equipment used on rolling stock"
●EN 45545 "Railway applications - Fire protection on railway vehicles"
Note
When used on railway stock, a stabilized power supply must be used to comply with
EN50155.
NEMA TS2 (EEC)
EEC versions meet the requirements of the standard
NEMA TS2 (Traffic Controller Assemblies with NTCIP Requirements)
FM
The product meets the requirements of the standards:
●Factory Mutual Approval Standard Class Number 3611
●FM Hazardous (Classified) Location Electrical Equipment:
Non Incendive / Class I / Division 2 / Groups A,B,C,D / T4 and
Non Incendive / Class I / Zone 2 / Group IIC / T4
cULus Approval for Information Technology Equipment
cULus Listed I. T. E.
Underwriters Laboratories Inc. complying with
●UL 60950-1 (Information Technology Equipment)
●CSA C22.2 No. 60950-1-03
Report no. E115352
cULus approval for industrial control equipment
cULus Listed I. T. E.
Underwriters Laboratories Inc. complying with
●UL 1604 (Information Technology Equipment) approved for use in Div. 2
or
●UL 2279 (Information Technology Equipment) approved for use in Zone 2 (Ex-Zone)

SCALANCE W1788-x
1.3 General approvals
Approvals SCALANCE W1700 802.11ac
18 Reference Manual, 11/2018, C79000-G8976-C487-02
Note for Australia - RCM
The product meets the requirements of the RCM standard.
Applied standards:
●AS/NZS CISPR11 (Industrial, scientific and medical equipment - Radio-frequency
disturbance characteristics - Limits and methods of measurement).
●EN 61000-6-4 Electromagnetic compatibility (EMC) - Part 6-4: Generic standards -
Emission standard for industrial environments
You will find the current versions of the standards in the currently valid RCM SDoCs (Self-
Declaration of Conformity).

SCALANCE W1788-x
1.4 National approvals
Approvals SCALANCE W1700 802.11ac
Reference Manual, 11/2018, C79000-G8976-C487-02 19
1.4
National approvals
The following table lists the countries in which the SCALANCE W1780 product is approved.
The diamond symbol (♦) identifies all countries or frequency ranges for which there was no
approval at the time these operating instructions were written.
The current status of the approvals can be found on the Internet at the following address:
Approvals (https://www.siemens.com/wireless-approvals).
Column
Meaning
Country
Country
Mode IEEE 802.11 standard and the TPC and / or DFS functionality, where required
CH
Channel
MHz
Frequency
PWR (EIRP)
Maximum permitted effective isotropic radiated power
MaxAntGain
Maximum permitted antenna gain
Use
Permitted use indoors and / or outdoors

SCALANCE W1788-x
1.4 National approvals
Approvals SCALANCE W1700 802.11ac
20 Reference Manual, 11/2018, C79000-G8976-C487-02
Country
Mode
CH
MHz
PWR
(EIRP)
MaxAntGai
n
Use
Albania
Andorra
Belgium
Bosnia and
Herzegovina
Bulgaria
Denmark
Germany
Estonia
Finland
France
Greece
United Kingdom
Ireland
Iceland
Italy
Croatia
Latvia
Liechtenstein
Lithuania
Luxembourg
Malta
Macedonia
Monaco
Montenegro
Netherlands
Norway
Austria
Poland
Portugal
Romania
San Marino
Sweden
Switzerland
Slovakia
Slovenia
Spain
Czech Republic
Turkey
Hungary
Vatican
Cyprus
11g 11n 1
-
13
2412
-
2472
100 mW
0 Indoor + Outdoor
11a 11c 11n
TPC
36
-
48
5180
-
5240
200 mW
0 Indoor only
11a 11c 11n
DFS + TPC
52
-
64
5260
-
5320
200 mW
0 Indoor only
100
-
140
5500
-
5700
1000 mW
0 Indoor + Outdoor
11a 11n 149
-
165
5745
-
5825
25 mW
0 Indoor + Outdoor
This manual suits for next models
5
Table of contents
Other Siemens Network Card manuals

Siemens
Siemens AFI5100 User manual

Siemens
Siemens S5-135U/155U User guide

Siemens
Siemens SIMATIC NET CP 343-1 User manual

Siemens
Siemens NRC User manual

Siemens
Siemens TIWAY I TI505 User manual

Siemens
Siemens SIMATIC NET CP 1623 User manual

Siemens
Siemens DTU3005-B User manual

Siemens
Siemens SIMATIC PCS 7 Reference manual
Popular Network Card manuals by other brands

Intel
Intel AnyPoint Wireless II Network user guide

MacroAir Technologies
MacroAir Technologies AirLynk BACnet Operation manual

TRENDnet
TRENDnet TE100-S4PCI Specifications

RTS
RTS TBX - TriBus ADAM User instructions

Dynex
Dynex DX-NNBC - N NOTEBOOK CARD WiFi Guide de l'utilisateur

Belkin
Belkin F8T006-PC user manual