Siemens Albatros2 RVS46 Series User manual

Edition 1.0
Controller series A
CE1U2353en01a
22. November 2006
Building Technologies
HVAC Products
Albatros2
Zone controler
User Manual OEM
RVS46..
AVS75..
AVS37..
QAA75..
QAA78..
QAA55..

2/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products 22. November 2006

3/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Table of contents 22. November 2006
Table of contents
1Overview of OEM settings ............................................................................... 4
2The settings in detail...................................................................................... 15
2.1 Operator section ............................................................................................ 15
Operation and display.................................................................................... 15
2.2 Heating circuits .............................................................................................. 15
mixing valve control ....................................................................................... 15
2.3 Domestic hot water........................................................................................ 16
Setpoints........................................................................................................ 16
Release ......................................................................................................... 16
2.4 Pump H1/H2 .................................................................................................. 17
pump H1 ........................................................................................................ 17
2.5 Primary controller / system pump .................................................................. 17
flow temperature setpoint limitations ............................................................. 17
mixing valve control ....................................................................................... 18
2.6 DHW storage tank ......................................................................................... 19
Release ......................................................................................................... 19
Charging control ............................................................................................ 19
Charging time limitation ................................................................................. 20
Discharging protection................................................................................... 20
Overtemperature protection........................................................................... 21
DHW push ..................................................................................................... 21
2.7 Configuration ................................................................................................. 21
Building and room model............................................................................... 21
Parameters .................................................................................................... 22
2.8 LPB................................................................................................................ 22
Error / maintenance / alarms .........................................................................22
Range of action of changeover...................................................................... 22
2.9 Error............................................................................................................... 23
History 1...10 ................................................................................................. 23
2.10 Diagnostics consumers ................................................................................. 23
Heating circuit 1, heating circuit 2, heating circuit P .....................................23

4/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
1 Overview of OEM settings
The table below shows all available settings up to the heating engineer level. However,
certain operating lines may be hidden, depending on the type of unit.
E = enduser I = commissioning F = heating engineer O = OEM
BZ = operating line
Operating line User level Function Default value Minimum Max Unit
Time of day and date
1 E Hours/minutes - 00:00 23:59 hh:mm
2 E Day/month - 01.01 31.12 dd.mm
3 E Year - 2004 2099 yyyy
5 F Start of summertime 25.03 01.01 31.12 dd.mm
6 F End of summertime 25.10 01.01 31.12 dd.mm
Operator section
20 E Language
German ¦ …
German -
22 F Info
Temporarily ¦ Permanently
Temporarily -
26 F Operation lock
Off ¦ On
Off -
27 F Programming lock
Off ¦ On
Off -
30 O Data:read
No ¦ Yes
No
31 O Data:write
No ¦ Yes
No
40 I Used as
Room unit 1 ¦ Room unit 2 ¦ Operator unit ¦Service unit
Room unit 1 -
42 I assignment room unit 1
Heating circuit 1 ¦ Heating circuits 1 and 2
Heating circuit 1 -
44 I Operation HC2
Commonly with HC1 ¦ Independently
Commonly with HC1 -
46 I Operation HCP
Commonly with HC1 ¦ Independently
Commonly with HC1 -
48 I Action occupancy button
None ¦ Heating circuit 1 ¦ Heating circuit 2 ¦ Commonly
Heating circuit 1 -
54 F Readjustment room sensor 0.0 -3 3 °C
70 F Software version - 0 99.9 -
Wireless
120 I Binding
No ¦ Yes
No
121 I Test mode
Off ¦ On
Off
130 I Room unit 1
Missing ¦ Ready ¦ No reception ¦ Change batt
- -
131 I Room unit 2
Missing ¦ Ready ¦ No reception ¦ Change batt
- -
132 I Outside sensor
Missing ¦ Ready ¦ No reception ¦ Change batt
- -
133 I Repeater
Missing ¦ Ready ¦ No reception
- -
Legend

5/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
134 I Operator unit
Missing ¦ Ready ¦ No reception ¦ Change batt
- -
135 I Service unit
Missing ¦ Ready ¦ No reception ¦ Change batt
- -
138 I Delete all devices
No ¦ Yes
No -
Time prog heating circuit 1
500 E Preselection
Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa
¦Su
Mo - Su -
501 E 1st phase on 6:00 00:00 24:00 hh:mm
502 E 1st phase off 22:00 00:00 24:00 hh:mm
503 E 2st phase on 24:00 00:00 24:00 hh:mm
504 E 2st phase off 24:00 00:00 24:00 hh:mm
505 E 3st phase on 24:00 00:00 24:00 hh:mm
506 E 3st phase off 24:00 00:00 24:00 hh:mm
516 E Default values
No ¦ Yes
No -
Time prog heating circuit 2
520 E Preselection
Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa
¦Su
Mo - Su -
521 E 1st phase on 6:00 00:00 24:00 hh:mm
522 E 1st phase off 22:00 00:00 24:00 hh:mm
523 E 2st phase on 24:00 00:00 24:00 hh:mm
524 E 2st phase off 24:00 00:00 24:00 hh:mm
525 E 3st phase on 24:00 00:00 24:00 hh:mm
526 E 3st phase off 24:00 00:00 24:00 hh:mm
536 E Default values
No ¦ Yes
No -
Time program 3 / HCP
540 E Preselection
Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa
¦Su
Mo - Su -
541 E 1st phase on 6:00 00:00 24:00 hh:mm
542 E 1st phase off 22:00 00:00 24:00 hh:mm
543 E 2st phase on 24:00 00:00 24:00 hh:mm
544 E 2st phase off 24:00 00:00 24:00 hh:mm
545 E 3st phase on 24:00 00:00 24:00 hh:mm
546 E 3st phase off 24:00 00:00 24:00 hh:mm
556 E Default values
No ¦ Yes
No -
Time program 4 / DHW
560 E Preselection
Mo - Su ¦ Mo - Fr ¦ Sa - Su ¦ Mo ¦ Tu ¦ We ¦ Th ¦ Fr ¦ Sa
¦Su
Mo - Su -
561 E 1st phase on 6:00 00:00 24:00 hh:mm
562 E 1st phase off 22:00 00:00 24:00 hh:mm
563 E 2st phase on 24:00 00:00 24:00 hh:mm
564 E 2st phase off 24:00 00:00 24:00 hh:mm
565 E 3st phase on 24:00 00:00 24:00 hh:mm
566 E 3st phase off 24:00 00:00 24:00 hh:mm

6/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
576 E Default values
No ¦ Yes
No -
Holidays heating circuit 1
641 E Preselection
Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period
6¦ Period 7¦ Period 8
Periode 1 -
642 E Start --.-- 01.01 31.12 dd.mm
643 E End --.-- 01.01 31.12 dd.mm
648 E Operating level
Frost protection ¦ Reduced
Frost protection -
Holidays heating circuit 2
651 E Preselection
Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period
6¦ Period 7¦ Period 8
Periode 1 -
652 E Start --.-- 01.01 31.12 dd.mm
653 E End --.-- 01.01 31.12 dd.mm
658 E Operating level
Frost protection ¦ Reduced
Frost protection -
Holidays heating circuit P
661 E Preselection
Period 1 ¦ Period 2 ¦ Period 3¦ Period 4¦ Period 5¦ Period
6¦ Period 7¦ Period 8
Periode 1 -
662 E Start --.-- 01.01 31.12 dd.mm
663 E End --.-- 01.01 31.12 dd.mm
668 E Operating level
Frost protection ¦ Reduced
Frost protection -
Heating circuit 1
710 E Comfort cooling setpoint 20.0 BZ 712 BZ 716 °C
712 E Reduced setpoint 16 BZ 714 BZ 710 °C
714 E Frost protection setpoint 10.0 4 BZ 712 °C
716 F Comfort setpoint max 35.0 BZ 710 35 °C
720 E Heating curve slope 1.50 0.10 4.00 -
721 F Heating curve displacement 0.0 -4.5 4.5 °C
726 F Heating curve adaption
Off ¦ On
Off -
730 E Summer/winter heating limit 18 −−−/ 8 30 °C
732 F 24-hour heating limit -3 −−−/ -10 10 °C
740 I Flow temp setpoint min 8 8 BZ 741 °C
741 I Flow temp setpoint max 80 BZ 740 95 °C
750 F Room influence 20 −−−/ 0 100 %
760 F Room temp limitation −−−−−−/ 0.5 4 °C
770 F Boost heating 5 −−−/ 0 20 °C
780 F Quick setback
Off ¦ Down to reduced setpoint ¦ Down to frost prot
setpoint
Down to reduced setpoint -
790 F Optimum start control max 0 0 360 min
791 F Optimum stop control max 0 0 360 min
800 F Reduced setp increase start −−−−−−/ -30 10 °C
801 F Reduced setp increase end -15 -30 BZ 800 °C
820 F Overtemp prot pump circuit
Off ¦ On
On -
830 F Mixing valve boost 10 0 50 °C

7/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
832 F Actuator:type
2-position ¦ 3-position
3-position -
833 F Switching differential 2-pos 2 0 20 °C
834 F Actuator: running time 120 30 873 s
835 O Mixing valve Xp 32 1 100 °C
836 O Mixing valve Tn 120 10 873 s
850 I Floor curing function
Off ¦ Functional heating ¦ Curing heating ¦
Functional/curing heating¦ Manually
Off -
851 I Floor curing setp manually 25 0 95 °C
861 F Excess heat draw
Off ¦ Heating mode ¦ Always
Always
872 F With prim contr/system pump
No ¦ Yes
Yes
900 I Optg mode changeover
Protection ¦ Recuced
Protection
Heating circuit 2
1010 E Comfort cooling setpoint 20.0 BZ 1012 BZ 1016 °C
1012 E Reduced setpoint 16 BZ 1014 BZ 1010 °C
1014 E Frost protection setpoint 10.0 4 BZ 1012 °C
1016 F Comfort setpoint max 35.0 BZ 1010 35 °C
1020 E Heating curve slope 1.50 0.10 4.00 -
1021 F Heating curve displacement 0.0 -4.5 4.5 °C
1026 F Heating curve adaption
Off ¦ On
Off -
1030 E Summer/winter heating limit 18 −−−/ 8 30 °C
1032 F 24-hour heating limit -3 −−−/ -10 10 °C
1040 I Flow temp setpoint min 8 8 BZ 1041 °C
1041 I Flow temp setpoint max 80 BZ 1040 95 °C
1050 F Room influence 20 −−−/ 0 100 %
1060 F Room temp limitation −−−−−−/ 0.5 4 °C
1070 F Boost heating 5 −−−/ 0 20 °C
1080 F Quick setback
Off ¦ Down to reduced setpoint ¦ Down to frost prot
setpoint
Down to reduced setpoint -
1090 F Optimum start control max 0 0 360 min
1091 F Optimum stop control max 0 0 360 min
1100 F Reduced setp increase start −−−−−−/ -30 10 °C
1101 F Reduced setp increase end -15 -30 BZ 1100 °C
1120 F Overtemp prot pump circuit
Off ¦ On
On -
1130 F Mixing valve boost 10 0 50 °C
1132 F Actuator:type
2-position ¦ 3-position
3-position -
1133 F Switching differential 2-pos 2 0 20 °C
1134 F Actuator: running time 120 30 873 s
1135 O Mixing valve Xp 32 1 100 °C
1136 O Mixing valve Tn 120 10 873 s
1150 F Floor curing function
Off ¦ Functional heating ¦ Curing heating ¦
Functional/curing heating¦ Manually
Off -

8/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
1151 F Floor curing setp manually 25 0 95 °C
1161 F Excess heat draw
Off ¦ Heating mode ¦ Always
Always
1172 F With prim contr/system pump
No ¦ Yes
Yes
1200 I Optg mode changeover
Protection ¦ Recuced
Protection
Heating circuit P
1300 E Operating mode
Protection ¦ Automatic ¦ Reduced ¦ Comfort
Automatic -
1310 E Comfort cooling setpoint 20.0 BZ 1012 BZ 1016 °C
1312 E Reduced setpoint 16 BZ 1014 BZ 1010 °C
1314 E Frost protection setpoint 10.0 4 BZ 1012 °C
1316 F Comfort setpoint max 35.0 BZ 1010 35 °C
1320 E Heating curve slope 1.50 0.10 4.00 -
1321 F Heating curve displacement 0.0 -4.5 4.5 °C
1326 F Heating curve adaption
Off ¦ On
Off -
1330 E Summer/winter heating limit 18 −−−/ 8 30 °C
1332 F 24-hour heating limit -3 −−−/ -10 10 °C
1340 F Flow temp setpoint min 8 8 BZ 1041 °C
1341 F Flow temp setpoint max 80 BZ 1040 95 °C
1350 F Room influence 20 −−−/ 0 100 %
1360 F Room temp limitation −−−−−−/ 0.5 4 °C
1370 F Boost heating 5 −−−/ 0 20 °C
1380 F Quick setback
Off ¦ Down to reduced setpoint ¦ Down to frost prot
setpoint
Down to reduced setpoint -
1390 F Optimum start control max 0 0 360 min
1391 F Optimum stop control max 0 0 360 min
1400 F Reduced setp increase start −−−−−−/ -30 10 °C
1401 F Reduced setp increase end -15 -30 BZ 1100 °C
1420 F Overtemp prot pump circuit
Off ¦ On
On -
1450 I Floor curing function
Off ¦ Functional heating ¦ Curing heating ¦
Functional/curing heating¦ Manually
Off -
1451 I Floor curing setp manually 25 0 95 °C
1455 F Floor curing setp current 0 0 95 °C
1456 F Floor curing day current 0 0 32 °C
1461 F Excess heat draw
Off ¦ Heating mode ¦ Always
Always
1172 F With prim contr/system pump
No ¦ Yes
Yes
1500 I Optg mode changeover
Protection ¦ Recuced
Protection
Domestic hot water
1610 E Nominal setpoint 55 BZ 1612 BZ 1614 OEM °C
1612 F Reduced setpoint 40 8 BZ 1610 °C
1614 O Nominal setpoint max 65 8 80 °C
1620 I Release
24h/day ¦ Time programs HCs ¦ Time program 4/DHW
Time programs HCs -

9/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
1630 I Charging priority
Absolute ¦ Shifting ¦ None ¦ MC shifting, PC absolute
MC shifting, PC absolute -
1640 F Legionella function
Off ¦ Periodically ¦ Fixed weekday
Fixed weekday -
1641 F Legionella funct periodically 3 1 7 Days
1642 F Legionella funct weekday
Monday ¦ Tuesday ¦ Wednesday ¦ Thursday ¦ Friday ¦
Saturday ¦ Sunday
Montag
1644 F Legionella funct time −−−−−−/ 00:00 23:50 hh:mm
1645 F Legionella funct setpoint 65 55 95 °C
1646 F Legionella funct duration 30 −−−/ 10 360 min
1647 F Legionella funct circ pump
Off ¦ On
On -
1660 F Release of the circulating pump
Time program 3/HCP ¦ DHW release ¦ Time program
4/DHW
DHW release -
1661 F Circulating pump cycling
Off ¦ On
On -
1663 F Circulaton setpoint 45 8 80 °C
Pump H1/H2
2008 O H1 DHW charging priority
No ¦ Yes
Yes
2010 F H1 Excess heat draw
Off ¦ On
On
2014 F H1 prim contr/system pump
No ¦ Yes
Yes -
2033 O H2 DHW charging priority
No ¦ Yes
Yes
2035 F H2 Excess heat draw
Off ¦ On
On
2039 F H2 prim contr/system pump
No ¦ Yes
Yes -
Primary controller / system pump
2110 O Flow temp setpoint min 8 8 95 °C
2111 O Flow temp setpoint max 80 8 95 °C
2130 O Mixing valve boost 10 0 50 °C
2132 O Actuator:type
2-position ¦ 3-position
3-position
2133 O Switching differential 2-pos 2 0 20 °C
2134 O Actuator: running time 120 30 873 °C
2135 O Mixing valve Xp 32 1 100 °C
2136 O Mixing valve Tn 120 10 873 °C
Solar
3810 F Temp diff on 8 BZ 3811 40 °C
3811 F Temp diff off 4 0 BZ 3812 °C
3812 F Charg temp min DHW st tank −−−−−−/ 8 95 °C
3830 F Collector start function −−−−−−/ 5 60 min
3831 F Min run time collector pump 60 5 120 s
3840 F Collector frost protection −−−−−−/ -20 5 °C
3850 F Collector overtemp prot −−−−−−/ 30 200 °C
3860 F Evaporation heat carrier −−−−−−/ 60 200 °C

10/26
Siemens Schweiz AG User Manual OEM CE1U2353en01a
HVAC Products Overview of OEM settings 22. November 2006
Operating line User level Function Default value Minimum Max Unit
DHW storage tank
5010 O Charging
Once/day ¦ Several times/day
Several times / day
5020 F Increase of the flow temperature setpoint 16 0 30 °C
5022 F Type of charging
With B3 ¦ With B3/B31 ¦ With B3, legio B3/B31
With B3/B31
5024 O Switching diff 5 0 20 °C
5030 O Charging time limitation 150 −−−/ 10 600 min
5040 O Discharging protection
Off ¦ Always ¦ Automatically
Automatic
5050 F Charging temp max 80 8 BZ 5051 OEM °C
5051 O Storage tank temp max 90 8 95 °C
5055 F Recooling temp 60 8 95 °C
5056 F Recooling heat gen/HCs
Off ¦ On
Off -
5057 F Recooling collector
Off ¦ Summer ¦ Always
Off -
5060 F Electric immersion heater:operating mode
Substitute ¦ Summer ¦ Always
Substitute -
5061 F Electric immersion heater:release
24h/day ¦ DHW release¦ Time program4/ DHW
DHW release -
5062 F El immersion heater control
External thermostat ¦ DHW sensor
DHW sensor -
5070 O Automatic push
Off ¦ On
On
5085 F Excess heat draw
Off ¦ On
On -
5092 F With prim contr/system pump
No ¦ Yes
No
5093 F With solar integration
No ¦ Yes
Yes
Configuration
5710 I Heating circuit 1
Off ¦ On
On -
5715 I Heating circuit 2
Off ¦ On
On -
5730 I DHW sensor B3
Sensor ¦ Thermostat
Sensors -
5731 I DHW controlling element Q3
None ¦ Charging pump ¦ Diverting valve
charging pump -
5890 I Relay output QX1
None ¦ Circulating pump Q4 ¦ El imm heater DHW K6 ¦
Collector pump Q5 ¦ H1 pump Q15 ¦ Alarm output K10 ¦
2nd pump speed HC1 Q21 ¦ 2nd pump speed HC2 Q22
¦ 2nd pump speed HCP Q23 ¦ Heat circuit pump HCP
Q20 ¦ H2 pump ¦ Q18 primary pump Q14
None -
5930 I Sensor input BX1
None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW
circulation sensor B39
None -
5931 I Sensor input BX2
None ¦ DHW sensor B31 ¦ Collector sensor B6 ¦ DHW
circulation sensor B39
None -