Signature Hardware Freestanding Tub Faucet Set User manual

1Freestanding Tub Faucet Set Installation Instructions
FREESTANDING TUB FAUCET SET
Before you begin, read the installation instructions below. Observe all local plumbing and building codes.
Caution: Do not grab or hold on to faucet or risers for support.
Unpack and inspect for any shipping damages. If any damage is found, contact Customer Service at 1-866-855-2284. If
you need assistance while installing your new faucet set, call our Customer Service number.
Your application and circumstances may call for variations to the installation instructions. We recommend consulting a
professional if you are unfamiliar with installing bathroom xtures and plumbing. Signature Hardware accepts no liability
for any damage to the oor, walls, plumbing, or personal injury during installation.
For the following installation instructions for your new faucet set it is assumed that the water supply lines are in place
underneath the oor and are directly accessible for installation
TOOLS AND MATERIALS:
Adjustable Wrench Damp Cloth
FAUCET INSTALLATION
1. Thread the bell anges (F), lock nuts (G), and rubber
washers (H) onto the lower riser pipes (E). Insert the lower
riser pipes into the installation holes in the nished oor.
Note: Apply the supplied thread sealant to all threaded
connections. Wipe away any excess sealant with a damp
cloth.
2. Thread the metal washers (I), and locknuts (J) onto the lower
riser pipes via the under the oor access space. Connect the
lower riser pipes to the main water supply with the rubber
washers (K) and NPT adapters (L).
3. Above the oor, apply thread sealant to the riser threads
and connect the shutoff valves (D). Wipe away any excess
sealant with a damp cloth.
4. Slide the slip nuts (B) up the upper riser pipes (C).
5. Wrap plumber's tape around the threads on the bottom of the
upper riser pipes and thread into the shutoff valves.
6. Place the remaining rubber washers (A) in the slip nuts at
the top of the supply pipes.
Floor
Bell Flange
Lock Nut
Rubber Washer
Metal Washer
Rubber Washer
Lock Nut
NPT Adapter
Lug ells or drop eared 90°
(Not included)
Support Mounted Between Floor Joists
Pliers Screwdrivers (Phillips and Flat Head)
Hacksaw Pipe Wrench Thread Sealant or Plumber’s Tape

2Freestanding Tub Faucet Set Installation Instructions
PARTS LIST:
A. (2) Rubber Washer
E. (2) Lower Riser Pipe
B. (2) Slip Nut
G. (2) Lock Nut
C. (2) Upper Riser Pipe
H. (2) Rubber Washer
D. (2) Straight Stop Valve
I. (2) Metal Washer
F. (2) Bell Flange
K. (2) Rubber Washer
J. (2) Lock Nut
L. (2) NPT Adapter
7. Close the shut-off valves and briey turn on the main water supply to check for leaks. If leakage occurs, tighten
the connections with an adjustable wrench as necessary. If problems persist, contact Customer Service.
8. Apply thread sealant to the outlets on the back of the faucet body. Attach the faucet to the upper riser pipes and
tighten the slips nuts to secure. Allow sealant to cure for 24 hours before use.
9. Attach the hand shower hose and rubber washers to the shower cradle outlet and hand-held shower. Place the
hand-held shower in the cradle.
10. Turn on the main water supply and open the shut-off valves.
11. To remove debris, turn the faucet on and allow the water to run through the spout for approximately 60 seconds.
Divert the water to the hand shower hose and allow the water to ow for approximately 60 seconds. Check to
make sure that all connections are tight.
A
F
E
D
C
B
H
G
I
J
K
L
Floor
C
H

3Freestanding Tub Faucet Set Installation Instructions
DRAIN INSTALLATION
Note: Because tubs vary in size, measure your space
thoroughly before installation. Trim pipes accordingly to
ensure a correct t. Go to the Trimming Drain Pipes
section for more information.
1. Apply thread sealant or plumber’s tape to the threads
at each end of all pipes prior to installation. If two pipes
arrive attached, be sure to take them apart and apply
sealant before installing.
2. Connect the tub shoe assembly (A), and rubber washer to
the tub drain (B).
3. Install the overow assembly (C) with the beveled washer,
overow plate, mounting screw (provided) and any other
washers or rubber sealing gaskets included.
4. Attach the waste and overow tee (D) to the overow
assembly (C) and shoe assembly (A) with sealing
washers and slip nuts.
5. Attach the drain tube and ange (E) to the waste and
overow tee (D) with the sealing washer and slip nut.
A
C
D
E
B
Press and Seal Swivel Drain
Press and Seal Swivel Drain
TRIMMING DRAIN PIPES
1. Connect the overow and drain assemblies and pipes to
the tub.
2. The T-connection will be attached at the points where the
drain pipes intersect. Measure and mark each pipe so
that the ends reach a little over halfway into the
T-Connection hubs.
3. Trim the pipes as necessary with a hack saw with a
blade that is suitable for cutting metal.