signia miniPocket User manual

miniPocket
User Guide

2
Content
Your remote control 4
Components 5
Key lock 6
Pairing hearing in󰘵ruments 7
Function overview 11
Further information 13
Cleaning 13
Replacing the battery 14
Troubleshooting 17

3
Service 19
Adju󰘵ing the signal 󰘵rength 20
Important safety information 22
Personal safety 22
Product safety 24
Important information 27
Intended use 27
Symbols 28
Operating, transport, and 󰘵orage conditions 30
Disposal information 31
Conformance information 32
Country-speci󰘰c information 33

4
Your remote control
miniPocket is a remote control for hearing in󰘵ruments. It
works with our speci󰘰c hearing in󰘵ruments. Your Hearing
Care Professional will advise you on the compatible models.
CAUTION
Read this user guide thoroughly and completely and
follow the safety information in this document to avoid
damage or injury.

5
Components
➊Status LED
➋Volume buttons
➌Keyring
➍Key lock switch
➎Program change button
➏Battery door remover tool
➎
➏
➍
➋
➊
➌

6
Key lock
XTo prevent any accidental
operation while the remote
control is in a pocket or bag,
move the key lock switch to
the lock position (red color visible).
When the key lock is active, all buttons on the remote control
are disabled.

7
Pairing hearing in󰄋ruments
Your hearing in󰘵ruments need to be paired with your
remote control. After that, the pairing is saved in the hearing
in󰘵ruments and remembered each time they are turned on.
XLock the remote control (red color visible).
XFir󰘵 turn the hearing in󰘵ruments o󰘯:
Open the battery compartments. If your hearing
in󰘵ruments do not have a battery compartment, turn them
o󰘯 as described in the hearing in󰘵ruments' user guide.
XThen turn the hearing in󰘵ruments on:
Close the battery compartments. If your hearing

8
in󰘵ruments do not have a battery compartment, turn them
on as described in the hearing in󰘵ruments' user guide.
The hearing in󰘵ruments are now in pairing mode. You have
3 minutes to complete the pairing. Follow the 󰘵eps below.
XInsert the hearing in󰘵ruments into your ears.
XHold down the button on the remote control while
switching the key lock to the unlock position (green color
visible).
XRelease the button.
The remote control is now in setup mode, the LED will be
on.

9
While the remote control is in setup mode, do not press
or . This would change other settings.
XHold down the button until the pairing con󰘰rmation
sound is played in the hearing in󰘵ruments. It takes
approximately 2 seconds for the sound to 󰘵art playing.
XEnsure that the con󰘰rmation sound is heard in both
hearing in󰘵ruments. When heard, the pairing will be
complete.

10
The remote control will remain in setup mode for an
additional 30 seconds. The con󰘰rmation sound can be
played again by pressing during these 30 seconds.
XTo exit the setup mode of the remote control, wait
30 seconds or move the key lock switch to the lock
position (red color visible).
When pairing is 󰘰nished, the remote control is ready for use.
XEnsure that it is unlocked (green color visible).
If the hearing in󰘵ruments could not be paired, refer to
"Troubleshooting" section.

11
Function overview
Function Description
Volume or
Press once to adju󰘵 the volume one level
at a time. Or, press and hold until desired
volume is reached.
Hearing
program
short press
➧ Switches to the next hearing program.
Turn on/o󰘯
(󰘵andby)
and long press (2 seconds)
➧ Turns your hearing in󰘵ruments on or o󰘯.

12
Function Description
Reset long press (2 seconds)
➧ Switches to hearing program 1 and sets the
default volume level.

13
Further information
Cleaning
NOTICE
XDo not put your remote control in water!
XDo not clean your remote control with
alcohol or benzine.
XClean the remote control as necessary with a dry or
slightly damp soft cloth.
Use only di󰘵illed water to dampen the cloth.
XAvoid any cleaning agents.

14
Replacing the battery
The remote control uses a CR 2450 button cell battery.
XAim the point of the
tool to the keyhole
above the battery
compartment cover ➊.
XPress the tool vertically
into the hole and at the
same time slide the
battery compartment
cover in the direction of
the arrow ➋.
XRemove the empty
battery by pulling the
removal 󰘱ap ➌.
Note: Please use the
provided tool to open the
battery compartment cover.
Any self‑made tool like
paper clips might damage
the child lock feature.

15
Insert the battery with the "+" symbol facing up:
XSlide it under the holder, then push it
down.

16
XAttach the cover by sliding it onto the remote control.
XTo Close; slide the battery compartment cover in and a
‘click’ sound will be heard when the child lock is properly
engaged. ➌

17
The pairing 󰘵atus is remembered by the remote control
when replacing the battery. There is no need to pair the
hearing in󰘵ruments again after battery replacement.
Troubleshooting
If the device does not work:
● Ensure that the battery is inserted correctly. Refer to
section "Replacing the battery".
● Ensure that the keys are not locked. Refer to section
"Key lock".
● Ensure that there is nothing between the hearing
in󰘵ruments and the remote control.

18
● Increase the signal 󰘵rength. Refer to section
"Adju󰘵ing the signal 󰘵rength".
● Pair the hearing in󰘵ruments again. Refer to section
"Pairing hearing in󰘵ruments".
● Ask your Hearing Care Professional if this remote control
is compatible with your hearing in󰘵ruments.
If the hearing in󰘵ruments cannot be paired:
● Increase the signal 󰘵rength. Refer to section
"Adju󰘵ing the signal 󰘵rength".
● Pair the hearing in󰘵ruments again. Refer to section
"Pairing hearing in󰘵ruments".

19
If the LED is no longer activating:
● Ensure that the keys are not locked. Refer to section
"Key lock".
● The battery may be low. Replace the empty battery.
Consult your Hearing Care Professional if you encounter
further problems.
Service
If you have technical problems with the device, consult your
Hearing Care Professional for service purposes. Do not
service or maintain the device while in use.

20
Adju󰄋ing the signal 󰄋rength
The remote control works by emitting a high‑frequency audio
signal. This signal may be heard by those under 30 years old.
Two signal 󰘵rength levels of the control signal are available.
By default, the remote control uses the 󰘵ronge󰘵 setting to
ensure a reliable connection with your hearing in󰘵ruments.
A lower signal 󰘵rength can be chosen if the control signal
di󰘵urbs others. Be aware that this can a󰘯ect the reliability of
the connection.
To adju󰘵 the signal 󰘵rength:
XLock the remote control (red color visible).
XHold down the button on the remote control while switch‑
ing the key lock to the unlock position (green color visible).