SIIG 32" User manual

04-0528D
Installation Instructions
Wall distance: 30mm / 1.2"
Bubble level included
Low Profile Universal TV Mount - 32" to 60"
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
Fixed LCD / TFT TV Wall Mount
Universal Mounting Pattern
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32" - 60"
Max load capacity:165 lbs / 75 kgs
1

AH
(×4) M8×35 screw
BI
(×4) M8/M6/M5 Washer
CJ
(×6) M8x80 Bolt
DK
(×6) M8 concrete
anchor
E L-1 (×6) M8 Washer
F L-2
GM
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source. Failure to do so
may result in damage to the display and could increase the risk of fire.
INSTALLATION AND OPERATING INSTRUCTIONS
CAUTION: The maximum load capacity is 165 lbs. Use with products exceeding the maximum load capacity may cause
serious injury. See apparatus instructions.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or mishandling
the display.
(×4) M5×16 screw
(×4) M8×16 screw
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any surface other
than wood studs, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood. The
installation instructions must be read to prevent personal injury and property damage. Keep these installation instructions
in an easily accessible location for future reference.
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
Caution
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the display and/or damage to the mounting surface.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the wall must be
reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the installation
instructions, must be adhered to. Failure to do so could result in serious personal injury.
Hardware kit:
(×4) M4×12 screw
(×4) M6×16 screw
(×4) M4×16 screw
(×4) M4×35 screw
(×4) M6×35 screw (×4) M8 Spacer
(×1) Bubble Level
2

1
2
3
4
a) Wood Stud Installation
3
4
5
6
7
8
Use a high-quality electronic stud finder (commercially available) to
locate dead center of two studs and mark their locations with a pencil
(figure 1-a).
Next, pre-drill a 3/16" hole to a depth of 3" in the wall stud at each
marked location.
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Step1: Wall Plate Installation
5/16" Socket and Wrench
Electric drill, 3/16" (4mm) drill bit for wood stud installation and 1/2" (13mm) masonry bit for concrete/brick installation
Note: Please ensure that the bubble level (L-2) is properly mounted on the wall plate prior to mounting the wall
plate.
You should mark four positions total.
Tighten the bolt with an open ended socket wrench by turning clockwise until tight.
2
1
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
Mark the right (upper and lower) and the left (upper and lower) positions
of the small horizontal slots that are in alignment with the studs (figure 1
-
c).
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
Attach the bubble level (L-2) to the wall plate and with the help of an
assistant ensure the wall plate is level, position the wall plate against
the wall in the desired mounting location (figure 1-b).
Phillips head screw driver
Stud finder for drywall installation
Tools Required:
Place the wall plate against the wall and line up the mounting slots with
the drilled holes. Check the bubble level to verify that the wall plate is
level.
For each location, insert a lag bolt (J) and washer (L-1) into the wall
(figure 1-c).
3

NOTE:
1
2
3
4
5
6
7
8 Do not tighten until all screws are in place.
5
1
2
Place your TV screen down on a soft, flat surface, and locate the
threaded mounting points that are located on the back of the display.
Step 2 Display Bracket Installation
To ensure optimal installation, this kit includes various screws of
different diameters and lengths.
2
Mark four holes to be used for securing the mount and place the wall
plate aside (figure 1-d).
Next, drill holes using an electric drill and 1/2" masonry bit to a depth of
3".
1
Attach the bubble level (L-2) to the wall plate, with the help of an
assistant place the wall plate into position against the wall, using the
bubble level to keep it level.
Once all of the anchors are in place, move the wall plate back into position. Check the bubble level to verify that the wall
plate is level.
The concrete anchors must be used for concrete installation.
b) Concrete/Brick Installation
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall.
According to the size of display's hole, choose the corresponding screw
and hole on the rectangle washer, then thread them in line as shown
(figure 2-a)
Check the mounting screws every two months for tightness.
Determine which screw (A/B/C/D/E/F/G/H) is of the correct length by
carefully inserting a straw, or toothpick, and mark how deep the
mounting point is.
Hook the TV rails over the top of the wall plate
(figure 3-a).
Then rotate the long screw at the bottom of the
display rail to tighten.
Maintenance
Step 3 Final Installation & Adjustment
Insert a concrete anchor into each hole.
4
3
Insert bolt (J) with washer (L-1) into each concrete anchor in the wall.
If your display has a curved back or a recessed thread mounting point,
place the spacer (M) between the mounting bracket and display. Then
choose screw (F/G/H) to match (figure 2-b).
4

Blank Page
5

Blank Page
6

• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no cost to the
customer.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then click RMA to submit a request to SIIG RMA or fax a request to 510-657-5962. If the product is
determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the product if
defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Please see our web site for more warranty details.
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or replaced.
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original package must be
included.
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted on the outside of the shipping carton.
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also
submit questions online and a technical support analysts will promptly respond.
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #: ________________
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the original purchaser and guarantees the product
to be free of any defects in materials or workmanship for five (5) years from the date of purchase of the product.
• You are responsible for the cost of shipping to SIIG. Ship the product to the following address:
Technical Support and Warranty
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store where you purchased from.
7

November, 2010 Copyright © 2010 by SIIG, Inc. All rights reserved.
Low Profile Universal TV Mount - 32" to 64" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other names
used in this publication are for identification only and may be trademarks of their respective owners.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA
Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/Notebook systems and
external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. All centered around the distribution and switching of A/V signals over CAT5/6, these products include matrix
switches, distribution amplifiers, extenders, converters, splitters, cabling, and more.
SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the Americas, as
well as through major distributors, system integrators, and VARs.
PRODUCT NAME
Low Profile Universal TV Mount - 32" to 60"
SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while keeping
economical and competitive prices. High-quality control standards are evident by one of the lowest defective return rates
in the industry. Our products offer comprehensive user manuals, user-friendly features, and most products are backed by
a lifetime warranty.
About SIIG, Inc.
8