SIKH HELMETS Y-61 User manual
A helmet may not always be able to protect you from injury.
Helmet fitting
You will only ensure optimal protection if your helmet fits just right.
Please note that for some kids, removing the comfort foam padding
attachments may provide the best fit. Please use the instructions in
the manual as a guide; you may also visit www.sikhhelmets.com for
further details to help with getting the right fit.
The helmet must not rest on the back of your head, but should not
be pulled too low on your forehead either and must not be shifted
to the left or right.
Adjusting the helmet
This helmet features a fit adjustment dial.
Place the helmet level on your head with the fitting ring open. The
bottom edge of the helmet must rest 1-2 finger-widths above the
top of your nose.
If the helmet can easily be
moved, the fitting ring (1l
must be set tighter. You do
this using the rotary knob (2).
Turning it clockwise makes
the circumference of the fitting ring smaller, turning it anti
clockwise make it bigger.
Tighten the fitting ring until it fully encircles your head and does
not become loose.
Adjusting the straps
In case of a fall, the helmet only
protects your head optimally if the
straps are correctly adjusted.
3
Place the two Y-shaped strap
holders (3) approx. 1 cm
below your ears.
Please read carefully and completely through these instructions for use.
These instructions form part of the product and contain important
information about the correct way to use and handle it. Always observe all
the safety advice.
The helmet you have just purchased provides protection whether on or off
the road. To ensure proper use of this helmet, familiarize yourself with its
features.
Properuse
This helmet is intended exclusively for use on nonmotorised bicycles,
skateboards, inline skates or kick scooters. Any use other than that
described here or modification to the product is not permitted and may
lead to damage to persons or property. There is also the risk of life-
threatening injury.
Safety
This helmet has been designed to absorb part of the energy of a fall.
WARNIN
G
: this helmet is suitable for bicycle, kick scooter, skateboard
and inline skating only.
WARNIN
G
: no helmet can protect against all injuries or death. For
maximum protection, the helmet must be fitted and adjusted properly as
per the instruction manual.
WARNIN
G
: a helmet that has received an impact may be damaged so
much that it no longer protects the rider, and such damage may not be
visible. Destroy and replace any helmet that has received such impact.
WARNIN
G
: common cleaners such as ammonia, bleach, etc. may
damage the helmet and the damage may not be visible. Clean with mild
soap and water only. Do not attach any stickers, it may damage the top
layer of the helmet. Do not expose the helmet to temperature higher than
+60°C (e.g. in a car).
WARNIN
G
: This helmet must not be used by children during climbing or
other activities where there is a risk of strangulation.
odel No.: Y-61
CPC (16 CRF 1203)
C (N10:2012+A1:2012)
CA (N10:2012+A1:2012)
AT (F12-22)
Fasten the strap buckle underneath
your chin (Fig. ). The chinstrap must
be pulled taut but not too tight. You
should be able to still open your mouth
slightly when the buckle is fastened.
The correct position for the fastened
chinstrap is underneath the lower jaw.
between the point of your chin and
your throat.
Press
4
Press
Always wear the helmet with the
chinstrap fastened.
If any of the straps
are too long or too
short, these can be
adjusted simply by
pulling them.
If the helmet does
not fit the size of
your head after all,
you should choose
another size or another helmet.
se only water, mild soap and a soft cloth for cleaning your helmet.
Common cleaners such as ammonia, bleach, etc. may damage the
helmet and the damage may not be visible. Do not attach any
stickers, it may damage the top layer of the helmet.
Standards
This helmet complies with .. CPC safety standards for bicycle
helmets for persons over age CPC (16 CRF 1203). This helmet also
meets the standards for: C (N10:2012+A1:2012), CA
(N10:2012+A1:2012) and AT (F12-22).
CPC and AT testing completed by:
SGS - CSTC Standards Technical Services Co., Ltd.
198 Kezhu Road, Scientech Park,
Guangzhou Economic & Technology Development District,
Guangzhou, Guangdong Province, China
C Certificate issued by:
T D Danmark
trandvejen 12
200 ellerup
Denmark
N 23
Address of
manufacturer
:
anufacturer: hanghai Cathay I.T. Co.,td.
Address: A-0, Noble Int
l Center, 0
iuwen Road,
inhang Disctrict, hanghai 201100, China.
Sold By:
ikh elmets Inc.
P.. ox 3006
rampton, N
6R 0
